xref: /openbmc/linux/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts (revision 6af72a31)

// SPDX-License-Identifier: BSD-3-Clause
/*
 * Copyright (c) 2021, The Linux Foundation. All rights reserved.
 * Copyright (c) 2022, Linaro Limited
 */

/dts-v1/;

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>

#include "sc8280xp.dtsi"
#include "sc8280xp-pmics.dtsi"

/ {
	model = "Qualcomm SC8280XP CRD";
	compatible = "qcom,sc8280xp-crd", "qcom,sc8280xp";

	aliases {
		serial0 = &qup2_uart17;
	};

	backlight {
		compatible = "pwm-backlight";
		pwms = <&pmc8280c_lpg 3 1000000>;
		enable-gpios = <&pmc8280_1_gpios 8 GPIO_ACTIVE_HIGH>;
		power-supply = <&vreg_edp_bl>;

		pinctrl-names = "default";
		pinctrl-0 = <&edp_bl_en>, <&edp_bl_pwm>;
	};

	chosen {
		stdout-path = "serial0:115200n8";
	};

	vreg_edp_bl: regulator-edp-bl {
		compatible = "regulator-fixed";

		regulator-name = "VREG_EDP_BL";
		regulator-min-microvolt = <3600000>;
		regulator-max-microvolt = <3600000>;

		gpio = <&pmc8280_1_gpios 9 GPIO_ACTIVE_HIGH>;
		enable-active-high;

		pinctrl-names = "default";
		pinctrl-0 = <&edp_bl_reg_en>;

		regulator-boot-on;
	};

	vreg_misc_3p3: regulator-misc-3p3 {
		compatible = "regulator-fixed";

		regulator-name = "VREG_MISC_3P3";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;

		gpio = <&pmc8280_1_gpios 1 GPIO_ACTIVE_HIGH>;
		enable-active-high;

		pinctrl-names = "default";
		pinctrl-0 = <&misc_3p3_reg_en>;

		regulator-boot-on;
		regulator-always-on;
	};
};

&apps_rsc {
	pmc8280-1-rpmh-regulators {
		compatible = "qcom,pm8350-rpmh-regulators";
		qcom,pmic-id = "b";

		vdd-l3-l5-supply = <&vreg_s11b>;

		vreg_s11b: smps11 {
			regulator-name = "vreg_s11b";
			regulator-min-microvolt = <1272000>;
			regulator-max-microvolt = <1272000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
		};

		vreg_l3b: ldo3 {
			regulator-name = "vreg_l3b";
			regulator-min-microvolt = <1200000>;
			regulator-max-microvolt = <1200000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-boot-on;
			regulator-always-on;
		};

		vreg_l4b: ldo4 {
			regulator-name = "vreg_l4b";
			regulator-min-microvolt = <912000>;
			regulator-max-microvolt = <912000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
		};

		vreg_l6b: ldo6 {
			regulator-name = "vreg_l6b";
			regulator-min-microvolt = <880000>;
			regulator-max-microvolt = <880000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
			regulator-boot-on;
		};
	};

	pmc8280c-rpmh-regulators {
		compatible = "qcom,pm8350c-rpmh-regulators";
		qcom,pmic-id = "c";

		vreg_l1c: ldo1 {
			regulator-name = "vreg_l1c";
			regulator-min-microvolt = <1800000>;
			regulator-max-microvolt = <1800000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
		};

		vreg_l7c: ldo7 {
			regulator-name = "vreg_l7c";
			regulator-min-microvolt = <2504000>;
			regulator-max-microvolt = <2504000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
		};

		vreg_l13c: ldo13 {
			regulator-name = "vreg_l13c";
			regulator-min-microvolt = <3072000>;
			regulator-max-microvolt = <3072000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
		};
	};

	pmc8280-2-rpmh-regulators {
		compatible = "qcom,pm8350-rpmh-regulators";
		qcom,pmic-id = "d";

		vdd-l1-l4-supply = <&vreg_s11b>;

		vreg_l3d: ldo3 {
			regulator-name = "vreg_l3d";
			regulator-min-microvolt = <1200000>;
			regulator-max-microvolt = <1200000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
		};

		vreg_l4d: ldo4 {
			regulator-name = "vreg_l4d";
			regulator-min-microvolt = <1200000>;
			regulator-max-microvolt = <1200000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
		};

		vreg_l6d: ldo6 {
			regulator-name = "vreg_l6d";
			regulator-min-microvolt = <880000>;
			regulator-max-microvolt = <880000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
		};

		vreg_l7d: ldo7 {
			regulator-name = "vreg_l7d";
			regulator-min-microvolt = <3072000>;
			regulator-max-microvolt = <3072000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
		};

		vreg_l9d: ldo9 {
			regulator-name = "vreg_l9d";
			regulator-min-microvolt = <912000>;
			regulator-max-microvolt = <912000>;
			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
			regulator-allow-set-load;
		};
	};
};

&pmc8280c_lpg {
	status = "okay";
};

&pmk8280_pon_pwrkey {
	status = "okay";
};

&qup0 {
	status = "okay";
};

&qup0_i2c4 {
	clock-frequency = <400000>;

	pinctrl-names = "default";
	pinctrl-0 = <&qup0_i2c4_default>, <&ts0_default>;

	status = "okay";

	touchscreen@10 {
		compatible = "hid-over-i2c";
		reg = <0x10>;
		hid-descr-addr = <0x1>;
		interrupts-extended = <&tlmm 175 IRQ_TYPE_LEVEL_LOW>;
		vdd-supply = <&vreg_misc_3p3>;
	};
};

&qup1 {
	status = "okay";
};

&qup2 {
	status = "okay";
};

&qup2_i2c5 {
	clock-frequency = <400000>;

	pinctrl-names = "default";
	pinctrl-0 = <&qup2_i2c5_default>, <&kybd_default>, <&tpad_default>;

	status = "okay";

	touchpad@15 {
		compatible = "hid-over-i2c";
		reg = <0x15>;
		hid-descr-addr = <0x1>;
		interrupts-extended = <&tlmm 182 IRQ_TYPE_LEVEL_LOW>;
		vdd-supply = <&vreg_misc_3p3>;
	};

	keyboard@68 {
		compatible = "hid-over-i2c";
		reg = <0x68>;
		hid-descr-addr = <0x1>;
		interrupts-extended = <&tlmm 104 IRQ_TYPE_LEVEL_LOW>;
		vdd-supply = <&vreg_misc_3p3>;
	};
};

&qup2_uart17 {
	compatible = "qcom,geni-debug-uart";

	status = "okay";
};

&remoteproc_adsp {
	firmware-name = "qcom/sc8280xp/qcadsp8280.mbn";

	status = "okay";
};

&remoteproc_nsp0 {
	firmware-name = "qcom/sc8280xp/qccdsp8280.mbn";

	status = "okay";
};

&ufs_mem_hc {
	reset-gpios = <&tlmm 228 GPIO_ACTIVE_LOW>;

	vcc-supply = <&vreg_l7c>;
	vcc-max-microamp = <800000>;
	vccq-supply = <&vreg_l3d>;
	vccq-max-microamp = <900000>;

	status = "okay";
};

&ufs_mem_phy {
	vdda-phy-supply = <&vreg_l6b>;
	vdda-pll-supply = <&vreg_l3b>;

	status = "okay";
};

&usb_0 {
	status = "okay";
};

&usb_0_dwc3 {
	/* TODO: Define USB-C connector properly */
	dr_mode = "host";
};

&usb_0_hsphy {
	vdda-pll-supply = <&vreg_l9d>;
	vdda18-supply = <&vreg_l1c>;
	vdda33-supply = <&vreg_l7d>;

	status = "okay";
};

&usb_0_qmpphy {
	vdda-phy-supply = <&vreg_l9d>;
	vdda-pll-supply = <&vreg_l4d>;

	status = "okay";
};

&usb_1 {
	status = "okay";
};

&usb_1_dwc3 {
	/* TODO: Define USB-C connector properly */
	dr_mode = "host";
};

&usb_1_hsphy {
	vdda-pll-supply = <&vreg_l4b>;
	vdda18-supply = <&vreg_l1c>;
	vdda33-supply = <&vreg_l13c>;

	status = "okay";
};

&usb_1_qmpphy {
	vdda-phy-supply = <&vreg_l4b>;
	vdda-pll-supply = <&vreg_l3b>;

	status = "okay";
};

&xo_board_clk {
	clock-frequency = <38400000>;
};

/* PINCTRL - additions to nodes defined in sc8280xp.dtsi */

&pmc8280_1_gpios {
	edp_bl_en: edp-bl-en-state {
		pins = "gpio8";
		function = "normal";
	};

	edp_bl_reg_en: edp-bl-reg-en-state {
		pins = "gpio9";
		function = "normal";
	};

	misc_3p3_reg_en: misc-3p3-reg-en-state {
		pins = "gpio1";
		function = "normal";
	};
};

&pmc8280c_gpios {
	edp_bl_pwm: edp-bl-pwm-state {
		pins = "gpio8";
		function = "func1";
	};
};

&tlmm {
	gpio-reserved-ranges = <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;

	kybd_default: kybd-default-state {
		disable {
			pins = "gpio102";
			function = "gpio";
			output-low;
		};

		int-n {
			pins = "gpio104";
			function = "gpio";
			bias-disable;
		};

		reset {
			pins = "gpio105";
			function = "gpio";
			bias-disable;
		};
	};

	qup0_i2c4_default: qup0-i2c4-default-state {
		pins = "gpio171", "gpio172";
		function = "qup4";

		bias-disable;
		drive-strength = <16>;
	};

	qup2_i2c5_default: qup2-i2c5-default-state {
		pins = "gpio81", "gpio82";
		function = "qup21";

		bias-disable;
		drive-strength = <16>;
	};

	tpad_default: tpad-default-state {
		int-n {
			pins = "gpio182";
			function = "gpio";
			bias-disable;
		};
	};

	ts0_default: ts0-default-state {
		int-n {
			pins = "gpio175";
			function = "gpio";
			bias-disable;
		};

		reset-n {
			pins = "gpio99";
			function = "gpio";
			output-high;
			drive-strength = <16>;
		};
	};
};