1// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2/*
3 * Google Lazor board device tree source
4 *
5 * Copyright 2020 Google LLC.
6 */
7
8#include "sc7180.dtsi"
9
10ap_ec_spi: &spi6 {};
11ap_h1_spi: &spi0 {};
12
13#include "sc7180-trogdor.dtsi"
14
15/ {
16	panel: panel {
17		compatible = "boe,nv133fhm-n62";
18		power-supply = <&pp3300_dx_edp>;
19		backlight = <&backlight>;
20		hpd-gpios = <&sn65dsi86_bridge 2 GPIO_ACTIVE_HIGH>;
21
22		ports {
23			port {
24				panel_in_edp: endpoint {
25					remote-endpoint = <&sn65dsi86_out>;
26				};
27			};
28		};
29	};
30};
31
32&ap_sar_sensor {
33	semtech,cs0-ground;
34	semtech,combined-sensors = <3>;
35	semtech,resolution = "fine";
36	semtech,startup-sensor = <0>;
37	semtech,proxraw-strength = <8>;
38	semtech,avg-pos-strength = <64>;
39};
40
41ap_ts_pen_1v8: &i2c4 {
42	status = "okay";
43	clock-frequency = <400000>;
44
45	ap_ts: touchscreen@10 {
46		compatible = "hid-over-i2c";
47		reg = <0x10>;
48		pinctrl-names = "default";
49		pinctrl-0 = <&ts_int_l>, <&ts_reset_l>;
50
51		interrupt-parent = <&tlmm>;
52		interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
53
54		post-power-on-delay-ms = <20>;
55		hid-descr-addr = <0x0001>;
56
57		vdd-supply = <&pp3300_ts>;
58	};
59};
60
61/* PINCTRL - modifications to sc7180-trogdor.dtsi */
62
63&ts_reset_l {
64	pinconf {
65		/* This pin is not connected on -rev0, pull up to park. */
66		/delete-property/bias-disable;
67		bias-pull-up;
68	};
69};
70
71/* PINCTRL - board-specific pinctrl */
72
73&tlmm {
74	gpio-line-names = "ESIM_MISO",
75			  "ESIM_MOSI",
76			  "ESIM_CLK",
77			  "ESIM_CS_L",
78			  "",
79			  "",
80			  "AP_TP_I2C_SDA",
81			  "AP_TP_I2C_SCL",
82			  "TS_RESET_L",
83			  "TS_INT_L",
84			  "",
85			  "EDP_BRIJ_IRQ",
86			  "AP_EDP_BKLTEN",
87			  "AP_RAM_ID2",
88			  "",
89			  "EDP_BRIJ_I2C_SDA",
90			  "EDP_BRIJ_I2C_SCL",
91			  "HUB_RST_L",
92			  "",
93			  "AP_RAM_ID1",
94			  "AP_SKU_ID2",
95			  "",
96			  "",
97			  "AMP_EN",
98			  "P_SENSOR_INT_L",
99			  "AP_SAR_SENSOR_SDA",
100			  "AP_SAR_SENSOR_SCL",
101			  "",
102			  "HP_IRQ",
103			  "AP_RAM_ID0",
104			  "EN_PP3300_DX_EDP",
105			  "AP_BRD_ID2",
106			  "BRIJ_SUSPEND",
107			  "AP_BRD_ID0",
108			  "AP_H1_SPI_MISO",
109			  "AP_H1_SPI_MOSI",
110			  "AP_H1_SPI_CLK",
111			  "AP_H1_SPI_CS_L",
112			  "",
113			  "",
114			  "",
115			  "",
116			  "H1_AP_INT_ODL",
117			  "",
118			  "UART_AP_TX_DBG_RX",
119			  "UART_DBG_TX_AP_RX",
120			  "HP_I2C_SDA",
121			  "HP_I2C_SCL",
122			  "FORCED_USB_BOOT",
123			  "",
124			  "",
125			  "AMP_DIN",
126			  "",
127			  "HP_BCLK",
128			  "HP_LRCLK",
129			  "HP_DOUT",
130			  "HP_DIN",
131			  "HP_MCLK",
132			  "TRACKPAD_INT_1V8_ODL",
133			  "AP_EC_SPI_MISO",
134			  "AP_EC_SPI_MOSI",
135			  "AP_EC_SPI_CLK",
136			  "AP_EC_SPI_CS_L",
137			  "AP_SPI_CLK",
138			  "AP_SPI_MOSI",
139			  "AP_SPI_MISO",
140			  /*
141			   * AP_FLASH_WP_L is crossystem ABI. Schematics
142			   * call it BIOS_FLASH_WP_L.
143			   */
144			  "AP_FLASH_WP_L",
145			  "DBG_SPI_HOLD_L",
146			  "AP_SPI_CS0_L",
147			  "",
148			  "",
149			  "",
150			  "",
151			  "",
152			  "",
153			  "UIM2_DATA",
154			  "UIM2_CLK",
155			  "UIM2_RST",
156			  "UIM2_PRESENT",
157			  "UIM1_DATA",
158			  "UIM1_CLK",
159			  "UIM1_RST",
160			  "",
161			  "EN_PP3300_CODEC",
162			  "EN_PP3300_HUB",
163			  "",
164			  "",
165			  "",
166			  "",
167			  "",
168			  "AP_SKU_ID1",
169			  "AP_RST_REQ",
170			  "",
171			  "AP_BRD_ID1",
172			  "AP_EC_INT_L",
173			  "",
174			  "",
175			  "",
176			  "",
177			  "",
178			  "",
179			  "",
180			  "",
181			  "",
182			  "EDP_BRIJ_EN",
183			  "AP_SKU_ID0",
184			  "",
185			  "",
186			  "",
187			  "",
188			  "",
189			  "",
190			  "",
191			  "",
192			  "",
193			  "AP_TS_PEN_I2C_SDA",
194			  "AP_TS_PEN_I2C_SCL",
195			  "DP_HOT_PLUG_DET",
196			  "EC_IN_RW_ODL";
197};
198