1// SPDX-License-Identifier: GPL-2.0 2/* 3 * Copyright (c) 2018, Linaro Limited 4 */ 5 6#include <dt-bindings/spmi/spmi.h> 7#include <dt-bindings/input/linux-event-codes.h> 8#include <dt-bindings/iio/qcom,spmi-vadc.h> 9#include <dt-bindings/thermal/thermal.h> 10 11/ { 12 thermal-zones { 13 pms405-thermal { 14 polling-delay-passive = <250>; 15 polling-delay = <1000>; 16 17 thermal-sensors = <&pms405_temp>; 18 19 trips { 20 pms405_alert0: pms405-alert0 { 21 temperature = <105000>; 22 hysteresis = <2000>; 23 type = "passive"; 24 }; 25 pms405_crit: pms405-crit { 26 temperature = <125000>; 27 hysteresis = <2000>; 28 type = "critical"; 29 }; 30 }; 31 }; 32 }; 33}; 34 35&spmi_bus { 36 pms405_0: pms405@0 { 37 compatible = "qcom,pms405", "qcom,spmi-pmic"; 38 reg = <0x0 SPMI_USID>; 39 #address-cells = <1>; 40 #size-cells = <0>; 41 42 pms405_gpios: gpio@c000 { 43 compatible = "qcom,pms405-gpio", "qcom,spmi-gpio"; 44 reg = <0xc000>; 45 gpio-controller; 46 gpio-ranges = <&pms405_gpios 0 0 12>; 47 #gpio-cells = <2>; 48 interrupt-controller; 49 #interrupt-cells = <2>; 50 }; 51 52 pon@800 { 53 compatible = "qcom,pms405-pon"; 54 reg = <0x0800>; 55 mode-bootloader = <0x2>; 56 mode-recovery = <0x1>; 57 58 pwrkey { 59 compatible = "qcom,pm8941-pwrkey"; 60 interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; 61 debounce = <15625>; 62 bias-pull-up; 63 linux,code = <KEY_POWER>; 64 }; 65 }; 66 67 pms405_temp: temp-alarm@2400 { 68 compatible = "qcom,spmi-temp-alarm"; 69 reg = <0x2400>; 70 interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>; 71 io-channels = <&pms405_adc ADC5_DIE_TEMP>; 72 io-channel-names = "thermal"; 73 #thermal-sensor-cells = <0>; 74 }; 75 76 pms405_adc: adc@3100 { 77 compatible = "qcom,pms405-adc", "qcom,spmi-adc-rev2"; 78 reg = <0x3100>; 79 interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; 80 #address-cells = <1>; 81 #size-cells = <0>; 82 #io-channel-cells = <1>; 83 84 ref_gnd@0 { 85 reg = <ADC5_REF_GND>; 86 qcom,pre-scaling = <1 1>; 87 }; 88 89 vref_1p25@1 { 90 reg = <ADC5_1P25VREF>; 91 qcom,pre-scaling = <1 1>; 92 }; 93 94 pon_1: vph_pwr@131 { 95 reg = <ADC5_VPH_PWR>; 96 qcom,pre-scaling = <1 3>; 97 }; 98 99 die_temp@6 { 100 reg = <ADC5_DIE_TEMP>; 101 qcom,pre-scaling = <1 1>; 102 }; 103 104 pa_therm1: thermistor1@77 { 105 reg = <ADC5_AMUX_THM1_100K_PU>; 106 qcom,ratiometric; 107 qcom,hw-settle-time = <200>; 108 qcom,pre-scaling = <1 1>; 109 }; 110 111 pa_therm3: thermistor3@79 { 112 reg = <ADC5_AMUX_THM3_100K_PU>; 113 qcom,ratiometric; 114 qcom,hw-settle-time = <200>; 115 qcom,pre-scaling = <1 1>; 116 }; 117 118 xo_therm: xo_temp@76 { 119 reg = <ADC5_XO_THERM_100K_PU>; 120 qcom,ratiometric; 121 qcom,hw-settle-time = <200>; 122 qcom,pre-scaling = <1 1>; 123 }; 124 }; 125 126 rtc@6000 { 127 compatible = "qcom,pm8941-rtc"; 128 reg = <0x6000>; 129 reg-names = "rtc", "alarm"; 130 interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>; 131 }; 132 }; 133 134 pms405_1: pms405@1 { 135 compatible = "qcom,pms405", "qcom,spmi-pmic"; 136 reg = <0x1 SPMI_USID>; 137 138 pms405_spmi_regulators: regulators { 139 compatible = "qcom,pms405-regulators"; 140 }; 141 }; 142}; 143