1// SPDX-License-Identifier: GPL-2.0-only OR BSD-3-Clause 2 3#include <dt-bindings/spmi/spmi.h> 4#include <dt-bindings/iio/qcom,spmi-vadc.h> 5 6&spmi_bus { 7 pmic@0 { 8 compatible = "qcom,pmp8074", "qcom,spmi-pmic"; 9 reg = <0x0 SPMI_USID>; 10 #address-cells = <1>; 11 #size-cells = <0>; 12 13 pmp8074_adc: adc@3100 { 14 compatible = "qcom,spmi-adc-rev2"; 15 reg = <0x3100>; 16 interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; 17 #address-cells = <1>; 18 #size-cells = <0>; 19 #io-channel-cells = <1>; 20 21 ref-gnd@0 { 22 reg = <ADC5_REF_GND>; 23 qcom,pre-scaling = <1 1>; 24 }; 25 26 vref-1p25@1 { 27 reg = <ADC5_1P25VREF>; 28 qcom,pre-scaling = <1 1>; 29 }; 30 31 vref-vadc@2 { 32 reg = <ADC5_VREF_VADC>; 33 qcom,pre-scaling = <1 1>; 34 }; 35 36 pmic_die: die-temp@6 { 37 reg = <ADC5_DIE_TEMP>; 38 qcom,pre-scaling = <1 1>; 39 }; 40 41 xo_therm: xo-temp@76 { 42 reg = <ADC5_XO_THERM_100K_PU>; 43 qcom,ratiometric; 44 qcom,hw-settle-time = <200>; 45 qcom,pre-scaling = <1 1>; 46 }; 47 48 pa_therm1: thermistor1@77 { 49 reg = <ADC5_AMUX_THM1_100K_PU>; 50 qcom,ratiometric; 51 qcom,hw-settle-time = <200>; 52 qcom,pre-scaling = <1 1>; 53 }; 54 55 pa_therm2: thermistor2@78 { 56 reg = <ADC5_AMUX_THM2_100K_PU>; 57 qcom,ratiometric; 58 qcom,hw-settle-time = <200>; 59 qcom,pre-scaling = <1 1>; 60 }; 61 62 pa_therm3: thermistor3@79 { 63 reg = <ADC5_AMUX_THM3_100K_PU>; 64 qcom,ratiometric; 65 qcom,hw-settle-time = <200>; 66 qcom,pre-scaling = <1 1>; 67 }; 68 69 vph-pwr@131 { 70 reg = <ADC5_VPH_PWR>; 71 qcom,pre-scaling = <1 3>; 72 }; 73 }; 74 75 pmp8074_rtc: rtc@6000 { 76 compatible = "qcom,pm8941-rtc"; 77 reg = <0x6000>; 78 reg-names = "rtc", "alarm"; 79 interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>; 80 allow-set-time; 81 status = "disabled"; 82 }; 83 84 pmp8074_gpios: gpio@c000 { 85 compatible = "qcom,pmp8074-gpio", "qcom,spmi-gpio"; 86 reg = <0xc000>; 87 gpio-controller; 88 #gpio-cells = <2>; 89 gpio-ranges = <&pmp8074_gpios 0 0 12>; 90 interrupt-controller; 91 #interrupt-cells = <2>; 92 }; 93 }; 94 95 pmic@1 { 96 compatible = "qcom,pmp8074", "qcom,spmi-pmic"; 97 reg = <0x1 SPMI_USID>; 98 99 regulators { 100 compatible = "qcom,pmp8074-regulators"; 101 102 s3: s3 { 103 regulator-name = "vdd_s3"; 104 regulator-min-microvolt = <592000>; 105 regulator-max-microvolt = <1064000>; 106 regulator-always-on; 107 regulator-boot-on; 108 }; 109 110 s4: s4 { 111 regulator-name = "vdd_s4"; 112 regulator-min-microvolt = <712000>; 113 regulator-max-microvolt = <992000>; 114 regulator-always-on; 115 regulator-boot-on; 116 }; 117 118 l11: l11 { 119 regulator-name = "l11"; 120 regulator-min-microvolt = <1800000>; 121 regulator-max-microvolt = <3300000>; 122 }; 123 }; 124 }; 125}; 126