1// SPDX-License-Identifier: GPL-2.0 2#include <dt-bindings/iio/qcom,spmi-vadc.h> 3#include <dt-bindings/input/linux-event-codes.h> 4#include <dt-bindings/interrupt-controller/irq.h> 5#include <dt-bindings/spmi/spmi.h> 6 7/ { 8 thermal-zones { 9 pm8994-thermal { 10 polling-delay-passive = <250>; 11 polling-delay = <1000>; 12 13 thermal-sensors = <&pm8994_temp>; 14 15 trips { 16 pm8994_alert0: pm8994-alert0 { 17 temperature = <95000>; 18 hysteresis = <2000>; 19 type = "passive"; 20 }; 21 pm8994_crit: pm8994-crit { 22 temperature = <125000>; 23 hysteresis = <2000>; 24 type = "critical"; 25 }; 26 }; 27 }; 28 }; 29}; 30 31&spmi_bus { 32 33 pmic@0 { 34 compatible = "qcom,pm8994", "qcom,spmi-pmic"; 35 reg = <0x0 SPMI_USID>; 36 #address-cells = <1>; 37 #size-cells = <0>; 38 39 rtc@6000 { 40 compatible = "qcom,pm8941-rtc"; 41 reg = <0x6000>, <0x6100>; 42 reg-names = "rtc", "alarm"; 43 interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; 44 }; 45 46 pm8994_pon: pon@800 { 47 compatible = "qcom,pm8916-pon"; 48 reg = <0x800>; 49 mode-bootloader = <0x2>; 50 mode-recovery = <0x1>; 51 52 pwrkey { 53 compatible = "qcom,pm8941-pwrkey"; 54 interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; 55 debounce = <15625>; 56 bias-pull-up; 57 linux,code = <KEY_POWER>; 58 }; 59 60 pm8994_resin: resin { 61 compatible = "qcom,pm8941-resin"; 62 interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; 63 debounce = <15625>; 64 bias-pull-up; 65 status = "disabled"; 66 }; 67 }; 68 69 pm8994_temp: temp-alarm@2400 { 70 compatible = "qcom,spmi-temp-alarm"; 71 reg = <0x2400>; 72 interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>; 73 io-channels = <&pm8994_vadc VADC_DIE_TEMP>; 74 io-channel-names = "thermal"; 75 #thermal-sensor-cells = <0>; 76 }; 77 78 pm8994_vadc: adc@3100 { 79 compatible = "qcom,spmi-vadc"; 80 reg = <0x3100>; 81 interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; 82 #address-cells = <1>; 83 #size-cells = <0>; 84 #io-channel-cells = <1>; 85 86 adc-chan@7 { 87 reg = <VADC_VSYS>; 88 qcom,pre-scaling = <1 3>; 89 label = "vph_pwr"; 90 }; 91 adc-chan@8 { 92 reg = <VADC_DIE_TEMP>; 93 label = "die_temp"; 94 }; 95 adc-chan@9 { 96 reg = <VADC_REF_625MV>; 97 label = "ref_625mv"; 98 }; 99 adc-chan@a { 100 reg = <VADC_REF_1250MV>; 101 label = "ref_1250mv"; 102 }; 103 adc-chan@e { 104 reg = <VADC_GND_REF>; 105 }; 106 adc-chan@f { 107 reg = <VADC_VDD_VADC>; 108 }; 109 }; 110 111 pm8994_gpios: gpio@c000 { 112 compatible = "qcom,pm8994-gpio", "qcom,spmi-gpio"; 113 reg = <0xc000>; 114 gpio-controller; 115 gpio-ranges = <&pm8994_gpios 0 0 22>; 116 #gpio-cells = <2>; 117 interrupt-controller; 118 #interrupt-cells = <2>; 119 }; 120 121 pm8994_mpps: mpps@a000 { 122 compatible = "qcom,pm8994-mpp", "qcom,spmi-mpp"; 123 reg = <0xa000>; 124 gpio-controller; 125 #gpio-cells = <2>; 126 gpio-ranges = <&pm8994_mpps 0 0 8>; 127 interrupt-controller; 128 #interrupt-cells = <2>; 129 }; 130 }; 131 132 pmic@1 { 133 compatible = "qcom,pm8994", "qcom,spmi-pmic"; 134 reg = <0x1 SPMI_USID>; 135 #address-cells = <1>; 136 #size-cells = <0>; 137 138 pm8994_lpg: pwm { 139 compatible = "qcom,pm8994-lpg"; 140 141 #address-cells = <1>; 142 #size-cells = <0>; 143 #pwm-cells = <2>; 144 145 status = "disabled"; 146 }; 147 148 pm8994_spmi_regulators: regulators { 149 compatible = "qcom,pm8994-regulators"; 150 }; 151 }; 152}; 153