1// SPDX-License-Identifier: BSD-3-Clause 2/* 3 * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. 4 * Copyright (c) 2019, Linaro Limited 5 */ 6 7#include <dt-bindings/iio/qcom,spmi-vadc.h> 8#include <dt-bindings/interrupt-controller/irq.h> 9#include <dt-bindings/spmi/spmi.h> 10 11/ { 12 thermal-zones { 13 pm8150b-thermal { 14 polling-delay-passive = <100>; 15 polling-delay = <0>; 16 17 thermal-sensors = <&pm8150b_temp>; 18 19 trips { 20 trip0 { 21 temperature = <95000>; 22 hysteresis = <0>; 23 type = "passive"; 24 }; 25 26 trip1 { 27 temperature = <115000>; 28 hysteresis = <0>; 29 type = "hot"; 30 }; 31 32 trip2 { 33 temperature = <145000>; 34 hysteresis = <0>; 35 type = "critical"; 36 }; 37 }; 38 }; 39 }; 40}; 41 42&spmi_bus { 43 pmic@2 { 44 compatible = "qcom,pm8150b", "qcom,spmi-pmic"; 45 reg = <0x2 SPMI_USID>; 46 #address-cells = <1>; 47 #size-cells = <0>; 48 49 pon@800 { 50 compatible = "qcom,pm8916-pon"; 51 reg = <0x0800>; 52 53 status = "disabled"; 54 }; 55 56 pm8150b_vbus: dcdc@1100 { 57 compatible = "qcom,pm8150b-vbus-reg"; 58 status = "disabled"; 59 reg = <0x1100>; 60 }; 61 62 pm8150b_temp: temp-alarm@2400 { 63 compatible = "qcom,spmi-temp-alarm"; 64 reg = <0x2400>; 65 interrupts = <0x2 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; 66 io-channels = <&pm8150b_adc ADC5_DIE_TEMP>; 67 io-channel-names = "thermal"; 68 #thermal-sensor-cells = <0>; 69 }; 70 71 pm8150b_adc: adc@3100 { 72 compatible = "qcom,spmi-adc5"; 73 reg = <0x3100>; 74 #address-cells = <1>; 75 #size-cells = <0>; 76 #io-channel-cells = <1>; 77 interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>; 78 79 ref-gnd@0 { 80 reg = <ADC5_REF_GND>; 81 qcom,pre-scaling = <1 1>; 82 label = "ref_gnd"; 83 }; 84 85 vref-1p25@1 { 86 reg = <ADC5_1P25VREF>; 87 qcom,pre-scaling = <1 1>; 88 label = "vref_1p25"; 89 }; 90 91 die-temp@6 { 92 reg = <ADC5_DIE_TEMP>; 93 qcom,pre-scaling = <1 1>; 94 label = "die_temp"; 95 }; 96 97 chg-temp@9 { 98 reg = <ADC5_CHG_TEMP>; 99 qcom,pre-scaling = <1 1>; 100 label = "chg_temp"; 101 }; 102 }; 103 104 pm8150b_adc_tm: adc-tm@3500 { 105 compatible = "qcom,spmi-adc-tm5"; 106 reg = <0x3500>; 107 interrupts = <0x2 0x35 0x0 IRQ_TYPE_EDGE_RISING>; 108 #thermal-sensor-cells = <1>; 109 #address-cells = <1>; 110 #size-cells = <0>; 111 status = "disabled"; 112 }; 113 114 pm8150b_gpios: gpio@c000 { 115 compatible = "qcom,pm8150b-gpio", "qcom,spmi-gpio"; 116 reg = <0xc000>; 117 gpio-controller; 118 gpio-ranges = <&pm8150b_gpios 0 0 12>; 119 #gpio-cells = <2>; 120 interrupt-controller; 121 #interrupt-cells = <2>; 122 }; 123 }; 124 125 pmic@3 { 126 compatible = "qcom,pm8150b", "qcom,spmi-pmic"; 127 reg = <0x3 SPMI_USID>; 128 #address-cells = <1>; 129 #size-cells = <0>; 130 131 pm8150b_lpg: pwm { 132 compatible = "qcom,pm8150b-lpg"; 133 134 #address-cells = <1>; 135 #size-cells = <0>; 136 #pwm-cells = <2>; 137 138 status = "disabled"; 139 }; 140 }; 141}; 142