1// SPDX-License-Identifier: BSD-3-Clause 2/* 3 * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. 4 * Copyright (c) 2019, Linaro Limited 5 */ 6 7#include <dt-bindings/iio/qcom,spmi-vadc.h> 8#include <dt-bindings/interrupt-controller/irq.h> 9#include <dt-bindings/spmi/spmi.h> 10 11/ { 12 thermal-zones { 13 pm8150b-thermal { 14 polling-delay-passive = <100>; 15 polling-delay = <0>; 16 17 thermal-sensors = <&pm8150b_temp>; 18 19 trips { 20 trip0 { 21 temperature = <95000>; 22 hysteresis = <0>; 23 type = "passive"; 24 }; 25 26 trip1 { 27 temperature = <115000>; 28 hysteresis = <0>; 29 type = "hot"; 30 }; 31 32 trip2 { 33 temperature = <145000>; 34 hysteresis = <0>; 35 type = "critical"; 36 }; 37 }; 38 }; 39 }; 40}; 41 42&spmi_bus { 43 pmic@2 { 44 compatible = "qcom,pm8150b", "qcom,spmi-pmic"; 45 reg = <0x2 SPMI_USID>; 46 #address-cells = <1>; 47 #size-cells = <0>; 48 49 power-on@800 { 50 compatible = "qcom,pm8916-pon"; 51 reg = <0x0800>; 52 53 status = "disabled"; 54 }; 55 56 pm8150b_temp: temp-alarm@2400 { 57 compatible = "qcom,spmi-temp-alarm"; 58 reg = <0x2400>; 59 interrupts = <0x2 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; 60 io-channels = <&pm8150b_adc ADC5_DIE_TEMP>; 61 io-channel-names = "thermal"; 62 #thermal-sensor-cells = <0>; 63 }; 64 65 pm8150b_adc: adc@3100 { 66 compatible = "qcom,spmi-adc5"; 67 reg = <0x3100>; 68 #address-cells = <1>; 69 #size-cells = <0>; 70 #io-channel-cells = <1>; 71 interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>; 72 73 ref-gnd@0 { 74 reg = <ADC5_REF_GND>; 75 qcom,pre-scaling = <1 1>; 76 label = "ref_gnd"; 77 }; 78 79 vref-1p25@1 { 80 reg = <ADC5_1P25VREF>; 81 qcom,pre-scaling = <1 1>; 82 label = "vref_1p25"; 83 }; 84 85 die-temp@6 { 86 reg = <ADC5_DIE_TEMP>; 87 qcom,pre-scaling = <1 1>; 88 label = "die_temp"; 89 }; 90 91 chg-temp@9 { 92 reg = <ADC5_CHG_TEMP>; 93 qcom,pre-scaling = <1 1>; 94 label = "chg_temp"; 95 }; 96 }; 97 98 pm8150b_adc_tm: adc-tm@3500 { 99 compatible = "qcom,spmi-adc-tm5"; 100 reg = <0x3500>; 101 interrupts = <0x2 0x35 0x0 IRQ_TYPE_EDGE_RISING>; 102 #thermal-sensor-cells = <1>; 103 #address-cells = <1>; 104 #size-cells = <0>; 105 status = "disabled"; 106 }; 107 108 pm8150b_gpios: gpio@c000 { 109 compatible = "qcom,pm8150b-gpio"; 110 reg = <0xc000>; 111 gpio-controller; 112 #gpio-cells = <2>; 113 interrupt-controller; 114 #interrupt-cells = <2>; 115 }; 116 }; 117 118 pmic@3 { 119 compatible = "qcom,pm8150b", "qcom,spmi-pmic"; 120 reg = <0x3 SPMI_USID>; 121 #address-cells = <1>; 122 #size-cells = <0>; 123 }; 124}; 125