1// SPDX-License-Identifier: GPL-2.0
2/* Copyright (c) 2016, The Linux Foundation. All rights reserved. */
3
4/dts-v1/;
5
6#include "msm8998.dtsi"
7#include "pm8005.dtsi"
8#include "pm8998.dtsi"
9#include "pmi8998.dtsi"
10
11/ {
12	model = "Qualcomm Technologies, Inc. MSM8998 v1 MTP";
13	compatible = "qcom,msm8998-mtp", "qcom,msm8998";
14	chassis-type = "handset";
15
16	qcom,board-id = <8 0>;
17
18	aliases {
19		serial0 = &blsp2_uart1;
20		serial1 = &blsp1_uart3;
21	};
22
23	chosen {
24		stdout-path = "serial0:115200n8";
25	};
26
27	vph_pwr: vph-pwr-regulator {
28		compatible = "regulator-fixed";
29		regulator-name = "vph_pwr";
30		regulator-always-on;
31		regulator-boot-on;
32	};
33};
34
35&blsp1_uart3 {
36	status = "okay";
37
38	bluetooth {
39		compatible = "qcom,wcn3990-bt";
40
41		vddio-supply = <&vreg_s4a_1p8>;
42		vddxo-supply = <&vreg_l7a_1p8>;
43		vddrf-supply = <&vreg_l17a_1p3>;
44		vddch0-supply = <&vreg_l25a_3p3>;
45		max-speed = <3200000>;
46	};
47};
48
49&blsp1_uart3_on {
50	rx-pins {
51		/delete-property/ bias-disable;
52		/*
53		 * Configure a pull-up on 45 (RX). This is needed to
54		 * avoid garbage data when the TX pin of the Bluetooth
55		 * module is in tri-state (module powered off or not
56		 * driving the signal yet).
57		 */
58		bias-pull-up;
59	};
60
61	cts-pins {
62		/delete-property/ bias-disable;
63		/*
64		 * Configure a pull-down on 47 (CTS) to match the pull
65		 * of the Bluetooth module.
66		 */
67		bias-pull-down;
68	};
69};
70
71&blsp2_uart1 {
72	status = "okay";
73};
74
75&etf {
76	status = "okay";
77};
78
79&etm1 {
80	status = "okay";
81};
82
83&etm2 {
84	status = "okay";
85};
86
87&etm3 {
88	status = "okay";
89};
90
91&etm4 {
92	status = "okay";
93};
94
95&etm5 {
96	status = "okay";
97};
98
99&etm6 {
100	status = "okay";
101};
102
103&etm7 {
104	status = "okay";
105};
106
107&etm8 {
108	status = "okay";
109};
110
111&etr {
112	status = "okay";
113};
114
115&funnel1 {
116	status = "okay";
117};
118
119&funnel2 {
120	status = "okay";
121};
122
123&funnel3 {
124	status = "okay";
125};
126
127&funnel4 {
128	/* FIXME: Figure out why clock late_initcall crashes the board with this enabled. */
129};
130
131&funnel5 {
132	/* FIXME: Figure out why clock late_initcall crashes the board with this enabled. */
133};
134
135&pcie0 {
136	status = "okay";
137};
138
139&pcie_phy {
140	status = "okay";
141};
142
143&pm8005_regulators {
144	vdd_s1-supply = <&vph_pwr>;
145
146	pm8005_s1: s1 { /* VDD_GFX supply */
147		regulator-min-microvolt = <524000>;
148		regulator-max-microvolt = <1100000>;
149		regulator-enable-ramp-delay = <500>;
150
151		/* Hack until we rig up the gpu consumer */
152		regulator-always-on;
153	};
154};
155
156&qusb2phy {
157	status = "okay";
158
159	vdda-pll-supply = <&vreg_l12a_1p8>;
160	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
161};
162
163&replicator1 {
164	status = "okay";
165};
166
167&rpm_requests {
168	regulators-0 {
169		compatible = "qcom,rpm-pm8998-regulators";
170
171		vdd_s1-supply = <&vph_pwr>;
172		vdd_s2-supply = <&vph_pwr>;
173		vdd_s3-supply = <&vph_pwr>;
174		vdd_s4-supply = <&vph_pwr>;
175		vdd_s5-supply = <&vph_pwr>;
176		vdd_s6-supply = <&vph_pwr>;
177		vdd_s7-supply = <&vph_pwr>;
178		vdd_s8-supply = <&vph_pwr>;
179		vdd_s9-supply = <&vph_pwr>;
180		vdd_s10-supply = <&vph_pwr>;
181		vdd_s11-supply = <&vph_pwr>;
182		vdd_s12-supply = <&vph_pwr>;
183		vdd_s13-supply = <&vph_pwr>;
184		vdd_l1_l27-supply = <&vreg_s7a_1p025>;
185		vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
186		vdd_l3_l11-supply = <&vreg_s7a_1p025>;
187		vdd_l4_l5-supply = <&vreg_s7a_1p025>;
188		vdd_l6-supply = <&vreg_s5a_2p04>;
189		vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
190		vdd_l9-supply = <&vreg_bob>;
191		vdd_l10_l23_l25-supply = <&vreg_bob>;
192		vdd_l13_l19_l21-supply = <&vreg_bob>;
193		vdd_l16_l28-supply = <&vreg_bob>;
194		vdd_l18_l22-supply = <&vreg_bob>;
195		vdd_l20_l24-supply = <&vreg_bob>;
196		vdd_l26-supply = <&vreg_s3a_1p35>;
197		vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
198
199		vreg_s3a_1p35: s3 {
200			regulator-min-microvolt = <1352000>;
201			regulator-max-microvolt = <1352000>;
202		};
203
204		vreg_s4a_1p8: s4 {
205			regulator-min-microvolt = <1800000>;
206			regulator-max-microvolt = <1800000>;
207			regulator-allow-set-load;
208		};
209
210		vreg_s5a_2p04: s5 {
211			regulator-min-microvolt = <1904000>;
212			regulator-max-microvolt = <2040000>;
213		};
214
215		vreg_s7a_1p025: s7 {
216			regulator-min-microvolt = <900000>;
217			regulator-max-microvolt = <1028000>;
218		};
219
220		vreg_l1a_0p875: l1 {
221			regulator-min-microvolt = <880000>;
222			regulator-max-microvolt = <880000>;
223		};
224
225		vreg_l2a_1p2: l2 {
226			regulator-min-microvolt = <1200000>;
227			regulator-max-microvolt = <1200000>;
228		};
229
230		vreg_l3a_1p0: l3 {
231			regulator-min-microvolt = <1000000>;
232			regulator-max-microvolt = <1000000>;
233		};
234
235		vreg_l5a_0p8: l5 {
236			regulator-min-microvolt = <800000>;
237			regulator-max-microvolt = <800000>;
238		};
239
240		vreg_l6a_1p8: l6 {
241			regulator-min-microvolt = <1808000>;
242			regulator-max-microvolt = <1808000>;
243		};
244
245		vreg_l7a_1p8: l7 {
246			regulator-min-microvolt = <1800000>;
247			regulator-max-microvolt = <1800000>;
248		};
249
250		vreg_l8a_1p2: l8 {
251			regulator-min-microvolt = <1200000>;
252			regulator-max-microvolt = <1200000>;
253		};
254
255		vreg_l9a_1p8: l9 {
256			regulator-min-microvolt = <1808000>;
257			regulator-max-microvolt = <2960000>;
258		};
259
260		vreg_l10a_1p8: l10 {
261			regulator-min-microvolt = <1808000>;
262			regulator-max-microvolt = <2960000>;
263		};
264
265		vreg_l11a_1p0: l11 {
266			regulator-min-microvolt = <1000000>;
267			regulator-max-microvolt = <1000000>;
268		};
269
270		vreg_l12a_1p8: l12 {
271			regulator-min-microvolt = <1800000>;
272			regulator-max-microvolt = <1800000>;
273		};
274
275		vreg_l13a_2p95: l13 {
276			regulator-min-microvolt = <1808000>;
277			regulator-max-microvolt = <2960000>;
278		};
279
280		vreg_l14a_1p88: l14 {
281			regulator-min-microvolt = <1880000>;
282			regulator-max-microvolt = <1880000>;
283		};
284
285		vreg_l15a_1p8: l15 {
286			regulator-min-microvolt = <1800000>;
287			regulator-max-microvolt = <1800000>;
288		};
289
290		vreg_l16a_2p7: l16 {
291			regulator-min-microvolt = <2704000>;
292			regulator-max-microvolt = <2704000>;
293		};
294
295		vreg_l17a_1p3: l17 {
296			regulator-min-microvolt = <1304000>;
297			regulator-max-microvolt = <1304000>;
298		};
299
300		vreg_l18a_2p7: l18 {
301			regulator-min-microvolt = <2704000>;
302			regulator-max-microvolt = <2704000>;
303		};
304
305		vreg_l19a_3p0: l19 {
306			regulator-min-microvolt = <3008000>;
307			regulator-max-microvolt = <3008000>;
308		};
309
310		vreg_l20a_2p95: l20 {
311			regulator-min-microvolt = <2960000>;
312			regulator-max-microvolt = <2960000>;
313			regulator-allow-set-load;
314		};
315
316		vreg_l21a_2p95: l21 {
317			regulator-min-microvolt = <2960000>;
318			regulator-max-microvolt = <2960000>;
319			regulator-system-load = <800000>;
320			regulator-allow-set-load;
321		};
322
323		vreg_l22a_2p85: l22 {
324			regulator-min-microvolt = <2864000>;
325			regulator-max-microvolt = <2864000>;
326		};
327
328		vreg_l23a_3p3: l23 {
329			regulator-min-microvolt = <3312000>;
330			regulator-max-microvolt = <3312000>;
331		};
332
333		vreg_l24a_3p075: l24 {
334			regulator-min-microvolt = <3088000>;
335			regulator-max-microvolt = <3088000>;
336		};
337
338		vreg_l25a_3p3: l25 {
339			regulator-min-microvolt = <3104000>;
340			regulator-max-microvolt = <3312000>;
341		};
342
343		vreg_l26a_1p2: l26 {
344			regulator-min-microvolt = <1200000>;
345			regulator-max-microvolt = <1200000>;
346			regulator-allow-set-load;
347		};
348
349		vreg_l28_3p0: l28 {
350			regulator-min-microvolt = <3008000>;
351			regulator-max-microvolt = <3008000>;
352		};
353
354		vreg_lvs1a_1p8: lvs1 {
355			regulator-min-microvolt = <1800000>;
356			regulator-max-microvolt = <1800000>;
357		};
358
359		vreg_lvs2a_1p8: lvs2 {
360			regulator-min-microvolt = <1800000>;
361			regulator-max-microvolt = <1800000>;
362		};
363
364	};
365
366	regulators-1 {
367		compatible = "qcom,rpm-pmi8998-regulators";
368
369		vdd_bob-supply = <&vph_pwr>;
370
371		vreg_bob: bob {
372			regulator-min-microvolt = <3312000>;
373			regulator-max-microvolt = <3600000>;
374		};
375	};
376};
377
378&remoteproc_adsp {
379	status = "okay";
380};
381
382&remoteproc_mss {
383	status = "okay";
384};
385
386&remoteproc_slpi {
387	status = "okay";
388};
389
390&tlmm {
391	gpio-reserved-ranges = <0 4>, <81 4>;
392};
393
394&sdhc2 {
395	status = "okay";
396	cd-gpios = <&tlmm 95 GPIO_ACTIVE_LOW>;
397
398	vmmc-supply = <&vreg_l21a_2p95>;
399	vqmmc-supply = <&vreg_l13a_2p95>;
400
401	pinctrl-names = "default", "sleep";
402	pinctrl-0 = <&sdc2_on &sdc2_cd>;
403	pinctrl-1 = <&sdc2_off &sdc2_cd>;
404};
405
406&stm {
407	status = "okay";
408};
409
410&ufshc {
411	status = "okay";
412	vcc-supply = <&vreg_l20a_2p95>;
413	vccq-supply = <&vreg_l26a_1p2>;
414	vccq2-supply = <&vreg_s4a_1p8>;
415	vcc-max-microamp = <750000>;
416	vccq-max-microamp = <560000>;
417	vccq2-max-microamp = <750000>;
418};
419
420&ufsphy {
421	status = "okay";
422	vdda-phy-supply = <&vreg_l1a_0p875>;
423	vdda-pll-supply = <&vreg_l2a_1p2>;
424	vddp-ref-clk-supply = <&vreg_l26a_1p2>;
425};
426
427&usb3 {
428	status = "okay";
429};
430
431&usb3_dwc3 {
432	dr_mode = "host"; /* Force to host until we have Type-C hooked up */
433};
434
435&usb3phy {
436	status = "okay";
437
438	vdda-phy-supply = <&vreg_l1a_0p875>;
439	vdda-pll-supply = <&vreg_l2a_1p2>;
440};
441
442&wifi {
443	status = "okay";
444
445	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
446	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
447	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
448	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
449};
450