1// SPDX-License-Identifier: GPL-2.0-only 2/* 3 * Copyright (c) 2015, The Linux Foundation. All rights reserved. 4 */ 5 6/dts-v1/; 7 8#include "msm8916-pm8916.dtsi" 9#include <dt-bindings/gpio/gpio.h> 10#include <dt-bindings/input/input.h> 11#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> 12#include <dt-bindings/pinctrl/qcom,pmic-mpp.h> 13#include <dt-bindings/sound/apq8016-lpass.h> 14 15/ { 16 model = "Qualcomm Technologies, Inc. APQ 8016 SBC"; 17 compatible = "qcom,apq8016-sbc", "qcom,apq8016"; 18 19 aliases { 20 serial0 = &blsp1_uart2; 21 serial1 = &blsp1_uart1; 22 usid0 = &pm8916_0; 23 i2c0 = &blsp_i2c2; 24 i2c1 = &blsp_i2c6; 25 i2c3 = &blsp_i2c4; 26 spi0 = &blsp_spi5; 27 spi1 = &blsp_spi3; 28 }; 29 30 chosen { 31 stdout-path = "serial0"; 32 }; 33 34 camera_vdddo_1v8: camera-vdddo-1v8 { 35 compatible = "regulator-fixed"; 36 regulator-name = "camera_vdddo"; 37 regulator-min-microvolt = <1800000>; 38 regulator-max-microvolt = <1800000>; 39 regulator-always-on; 40 }; 41 42 camera_vdda_2v8: camera-vdda-2v8 { 43 compatible = "regulator-fixed"; 44 regulator-name = "camera_vdda"; 45 regulator-min-microvolt = <2800000>; 46 regulator-max-microvolt = <2800000>; 47 regulator-always-on; 48 }; 49 50 camera_vddd_1v5: camera-vddd-1v5 { 51 compatible = "regulator-fixed"; 52 regulator-name = "camera_vddd"; 53 regulator-min-microvolt = <1500000>; 54 regulator-max-microvolt = <1500000>; 55 regulator-always-on; 56 }; 57 58 reserved-memory { 59 ramoops@bff00000 { 60 compatible = "ramoops"; 61 reg = <0x0 0xbff00000 0x0 0x100000>; 62 63 record-size = <0x20000>; 64 console-size = <0x20000>; 65 ftrace-size = <0x20000>; 66 }; 67 }; 68 69 usb2513 { 70 compatible = "smsc,usb3503"; 71 reset-gpios = <&pm8916_gpios 3 GPIO_ACTIVE_LOW>; 72 initial-mode = <1>; 73 }; 74 75 usb_id: usb-id { 76 compatible = "linux,extcon-usb-gpio"; 77 id-gpio = <&msmgpio 121 GPIO_ACTIVE_HIGH>; 78 pinctrl-names = "default"; 79 pinctrl-0 = <&usb_id_default>; 80 }; 81 82 hdmi-out { 83 compatible = "hdmi-connector"; 84 type = "a"; 85 86 port { 87 hdmi_con: endpoint { 88 remote-endpoint = <&adv7533_out>; 89 }; 90 }; 91 }; 92 93 gpio-keys { 94 compatible = "gpio-keys"; 95 #address-cells = <1>; 96 #size-cells = <0>; 97 autorepeat; 98 99 pinctrl-names = "default"; 100 pinctrl-0 = <&msm_key_volp_n_default>; 101 102 button@0 { 103 label = "Volume Up"; 104 linux,code = <KEY_VOLUMEUP>; 105 gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>; 106 }; 107 }; 108 109 leds { 110 pinctrl-names = "default"; 111 pinctrl-0 = <&msmgpio_leds>, 112 <&pm8916_gpios_leds>, 113 <&pm8916_mpps_leds>; 114 115 compatible = "gpio-leds"; 116 117 led@1 { 118 label = "apq8016-sbc:green:user1"; 119 gpios = <&msmgpio 21 GPIO_ACTIVE_HIGH>; 120 linux,default-trigger = "heartbeat"; 121 default-state = "off"; 122 }; 123 124 led@2 { 125 label = "apq8016-sbc:green:user2"; 126 gpios = <&msmgpio 120 GPIO_ACTIVE_HIGH>; 127 linux,default-trigger = "mmc0"; 128 default-state = "off"; 129 }; 130 131 led@3 { 132 label = "apq8016-sbc:green:user3"; 133 gpios = <&pm8916_gpios 1 GPIO_ACTIVE_HIGH>; 134 linux,default-trigger = "mmc1"; 135 default-state = "off"; 136 }; 137 138 led@4 { 139 label = "apq8016-sbc:green:user4"; 140 gpios = <&pm8916_gpios 2 GPIO_ACTIVE_HIGH>; 141 linux,default-trigger = "none"; 142 panic-indicator; 143 default-state = "off"; 144 }; 145 146 led@5 { 147 label = "apq8016-sbc:yellow:wlan"; 148 gpios = <&pm8916_mpps 2 GPIO_ACTIVE_HIGH>; 149 linux,default-trigger = "phy0tx"; 150 default-state = "off"; 151 }; 152 153 led@6 { 154 label = "apq8016-sbc:blue:bt"; 155 gpios = <&pm8916_mpps 3 GPIO_ACTIVE_HIGH>; 156 linux,default-trigger = "bluetooth-power"; 157 default-state = "off"; 158 }; 159 }; 160}; 161 162&blsp_dma { 163 status = "okay"; 164}; 165 166&blsp_i2c2 { 167 /* On Low speed expansion */ 168 status = "okay"; 169 label = "LS-I2C0"; 170}; 171 172&blsp_i2c4 { 173 /* On High speed expansion */ 174 status = "okay"; 175 label = "HS-I2C2"; 176 177 adv_bridge: bridge@39 { 178 status = "okay"; 179 180 compatible = "adi,adv7533"; 181 reg = <0x39>; 182 183 interrupt-parent = <&msmgpio>; 184 interrupts = <31 IRQ_TYPE_EDGE_FALLING>; 185 186 adi,dsi-lanes = <4>; 187 clocks = <&rpmcc RPM_SMD_BB_CLK2>; 188 clock-names = "cec"; 189 190 pd-gpios = <&msmgpio 32 GPIO_ACTIVE_HIGH>; 191 192 avdd-supply = <&pm8916_l6>; 193 v1p2-supply = <&pm8916_l6>; 194 v3p3-supply = <&pm8916_l17>; 195 196 pinctrl-names = "default","sleep"; 197 pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>; 198 pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>; 199 #sound-dai-cells = <1>; 200 201 ports { 202 #address-cells = <1>; 203 #size-cells = <0>; 204 205 port@0 { 206 reg = <0>; 207 adv7533_in: endpoint { 208 remote-endpoint = <&dsi0_out>; 209 }; 210 }; 211 212 port@1 { 213 reg = <1>; 214 adv7533_out: endpoint { 215 remote-endpoint = <&hdmi_con>; 216 }; 217 }; 218 }; 219 }; 220}; 221 222&blsp_i2c6 { 223 /* On Low speed expansion */ 224 status = "okay"; 225 label = "LS-I2C1"; 226}; 227 228&blsp_spi3 { 229 /* On High speed expansion */ 230 status = "okay"; 231 label = "HS-SPI1"; 232}; 233 234&blsp_spi5 { 235 /* On Low speed expansion */ 236 status = "okay"; 237 label = "LS-SPI0"; 238}; 239 240&blsp1_uart1 { 241 status = "okay"; 242 label = "LS-UART0"; 243}; 244 245&blsp1_uart2 { 246 status = "okay"; 247 label = "LS-UART1"; 248}; 249 250&camss { 251 status = "okay"; 252 ports { 253 port@0 { 254 reg = <0>; 255 csiphy0_ep: endpoint { 256 clock-lanes = <1>; 257 data-lanes = <0 2>; 258 remote-endpoint = <&ov5640_ep>; 259 status = "okay"; 260 }; 261 }; 262 }; 263}; 264 265&cci { 266 status = "okay"; 267}; 268 269&cci_i2c0 { 270 camera_rear@3b { 271 compatible = "ovti,ov5640"; 272 reg = <0x3b>; 273 274 enable-gpios = <&msmgpio 34 GPIO_ACTIVE_HIGH>; 275 reset-gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>; 276 pinctrl-names = "default"; 277 pinctrl-0 = <&camera_rear_default>; 278 279 clocks = <&gcc GCC_CAMSS_MCLK0_CLK>; 280 clock-names = "xclk"; 281 clock-frequency = <23880000>; 282 283 vdddo-supply = <&camera_vdddo_1v8>; 284 vdda-supply = <&camera_vdda_2v8>; 285 vddd-supply = <&camera_vddd_1v5>; 286 287 /* No camera mezzanine by default */ 288 status = "disabled"; 289 290 port { 291 ov5640_ep: endpoint { 292 clock-lanes = <1>; 293 data-lanes = <0 2>; 294 remote-endpoint = <&csiphy0_ep>; 295 }; 296 }; 297 }; 298}; 299 300&dsi0_out { 301 data-lanes = <0 1 2 3>; 302 remote-endpoint = <&adv7533_in>; 303}; 304 305&lpass { 306 status = "okay"; 307}; 308 309&mdss { 310 status = "okay"; 311}; 312 313&mpss { 314 status = "okay"; 315 316 firmware-name = "qcom/apq8016/mba.mbn", "qcom/apq8016/modem.mbn"; 317}; 318 319&pm8916_resin { 320 status = "okay"; 321 linux,code = <KEY_VOLUMEDOWN>; 322}; 323 324&pronto { 325 status = "okay"; 326 327 firmware-name = "qcom/apq8016/wcnss.mbn"; 328}; 329 330&sdhc_1 { 331 status = "okay"; 332 333 pinctrl-names = "default", "sleep"; 334 pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; 335 pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; 336}; 337 338&sdhc_2 { 339 status = "okay"; 340 341 pinctrl-names = "default", "sleep"; 342 pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>; 343 pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; 344 345 cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>; 346}; 347 348&sound { 349 status = "okay"; 350 351 pinctrl-0 = <&cdc_pdm_lines_act &ext_sec_tlmm_lines_act &ext_mclk_tlmm_lines_act>; 352 pinctrl-1 = <&cdc_pdm_lines_sus &ext_sec_tlmm_lines_sus &ext_mclk_tlmm_lines_sus>; 353 pinctrl-names = "default", "sleep"; 354 qcom,model = "DB410c"; 355 qcom,audio-routing = 356 "AMIC2", "MIC BIAS Internal2", 357 "AMIC3", "MIC BIAS External1"; 358 359 external-dai-link@0 { 360 link-name = "ADV7533"; 361 cpu { 362 sound-dai = <&lpass MI2S_QUATERNARY>; 363 }; 364 codec { 365 sound-dai = <&adv_bridge 0>; 366 }; 367 }; 368 369 internal-codec-playback-dai-link@0 { 370 link-name = "WCD"; 371 cpu { 372 sound-dai = <&lpass MI2S_PRIMARY>; 373 }; 374 codec { 375 sound-dai = <&lpass_codec 0>, <&wcd_codec 0>; 376 }; 377 }; 378 379 internal-codec-capture-dai-link@0 { 380 link-name = "WCD-Capture"; 381 cpu { 382 sound-dai = <&lpass MI2S_TERTIARY>; 383 }; 384 codec { 385 sound-dai = <&lpass_codec 1>, <&wcd_codec 1>; 386 }; 387 }; 388}; 389 390&usb { 391 status = "okay"; 392 extcon = <&usb_id>, <&usb_id>; 393 394 pinctrl-names = "default", "device"; 395 pinctrl-0 = <&usb_sw_sel_pm &usb_hub_reset_pm>; 396 pinctrl-1 = <&usb_sw_sel_pm_device &usb_hub_reset_pm_device>; 397}; 398 399&usb_hs_phy { 400 extcon = <&usb_id>; 401}; 402 403&wcd_codec { 404 clocks = <&gcc GCC_CODEC_DIGCODEC_CLK>; 405 clock-names = "mclk"; 406 qcom,mbhc-vthreshold-low = <75 150 237 450 500>; 407 qcom,mbhc-vthreshold-high = <75 150 237 450 500>; 408}; 409 410&wcnss_ctrl { 411 firmware-name = "qcom/apq8016/WCNSS_qcom_wlan_nv_sbc.bin"; 412}; 413 414/* Enable CoreSight */ 415&cti0 { status = "okay"; }; 416&cti1 { status = "okay"; }; 417&cti12 { status = "okay"; }; 418&cti13 { status = "okay"; }; 419&cti14 { status = "okay"; }; 420&cti15 { status = "okay"; }; 421&debug0 { status = "okay"; }; 422&debug1 { status = "okay"; }; 423&debug2 { status = "okay"; }; 424&debug3 { status = "okay"; }; 425&etf { status = "okay"; }; 426&etm0 { status = "okay"; }; 427&etm1 { status = "okay"; }; 428&etm2 { status = "okay"; }; 429&etm3 { status = "okay"; }; 430&etr { status = "okay"; }; 431&funnel0 { status = "okay"; }; 432&funnel1 { status = "okay"; }; 433&replicator { status = "okay"; }; 434&stm { status = "okay"; }; 435&tpiu { status = "okay"; }; 436 437&smd_rpm_regulators { 438 vdd_l1_l2_l3-supply = <&pm8916_s3>; 439 vdd_l4_l5_l6-supply = <&pm8916_s4>; 440 vdd_l7-supply = <&pm8916_s4>; 441 442 s3 { 443 regulator-min-microvolt = <375000>; 444 regulator-max-microvolt = <1562000>; 445 }; 446 447 s4 { 448 regulator-min-microvolt = <1800000>; 449 regulator-max-microvolt = <1800000>; 450 451 regulator-always-on; 452 regulator-boot-on; 453 }; 454 455 l1 { 456 regulator-min-microvolt = <375000>; 457 regulator-max-microvolt = <1525000>; 458 }; 459 460 l2 { 461 regulator-min-microvolt = <1200000>; 462 regulator-max-microvolt = <1200000>; 463 }; 464 465 l4 { 466 regulator-min-microvolt = <1750000>; 467 regulator-max-microvolt = <3337000>; 468 }; 469 470 l5 { 471 regulator-min-microvolt = <1750000>; 472 regulator-max-microvolt = <3337000>; 473 }; 474 475 l6 { 476 regulator-min-microvolt = <1800000>; 477 regulator-max-microvolt = <1800000>; 478 }; 479 480 l7 { 481 regulator-min-microvolt = <1750000>; 482 regulator-max-microvolt = <3337000>; 483 }; 484 485 l8 { 486 regulator-min-microvolt = <1750000>; 487 regulator-max-microvolt = <3337000>; 488 }; 489 490 l9 { 491 regulator-min-microvolt = <1750000>; 492 regulator-max-microvolt = <3337000>; 493 }; 494 495 l10 { 496 regulator-min-microvolt = <1750000>; 497 regulator-max-microvolt = <3337000>; 498 }; 499 500 l11 { 501 regulator-min-microvolt = <1750000>; 502 regulator-max-microvolt = <3337000>; 503 regulator-allow-set-load; 504 regulator-system-load = <200000>; 505 }; 506 507 l12 { 508 regulator-min-microvolt = <1750000>; 509 regulator-max-microvolt = <3337000>; 510 }; 511 512 l13 { 513 regulator-min-microvolt = <1750000>; 514 regulator-max-microvolt = <3337000>; 515 }; 516 517 l14 { 518 regulator-min-microvolt = <1750000>; 519 regulator-max-microvolt = <3337000>; 520 }; 521 522 /** 523 * 1.8v required on LS expansion 524 * for mezzanine boards 525 */ 526 l15 { 527 regulator-min-microvolt = <1750000>; 528 regulator-max-microvolt = <3337000>; 529 regulator-always-on; 530 }; 531 532 l16 { 533 regulator-min-microvolt = <1750000>; 534 regulator-max-microvolt = <3337000>; 535 }; 536 537 l17 { 538 regulator-min-microvolt = <3300000>; 539 regulator-max-microvolt = <3300000>; 540 }; 541 542 l18 { 543 regulator-min-microvolt = <1750000>; 544 regulator-max-microvolt = <3337000>; 545 }; 546}; 547 548/* 549 * 2mA drive strength is not enough when connecting multiple 550 * I2C devices with different pull up resistors. 551 */ 552&i2c2_default { 553 drive-strength = <16>; 554}; 555 556&i2c4_default { 557 drive-strength = <16>; 558}; 559 560&i2c6_default { 561 drive-strength = <16>; 562}; 563 564/* 565 * GPIO name legend: proper name = the GPIO line is used as GPIO 566 * NC = not connected (pin out but not routed from the chip to 567 * anything the board) 568 * "[PER]" = pin is muxed for [peripheral] (not GPIO) 569 * LSEC = Low Speed External Connector 570 * HSEC = High Speed External Connector 571 * 572 * Line names are taken from the schematic "DragonBoard410c" 573 * dated monday, august 31, 2015. Page 5 in particular. 574 * 575 * For the lines routed to the external connectors the 576 * lines are named after the 96Boards CE Specification 1.0, 577 * Appendix "Expansion Connector Signal Description". 578 * 579 * When the 96Board naming of a line and the schematic name of 580 * the same line are in conflict, the 96Board specification 581 * takes precedence, which means that the external UART on the 582 * LSEC is named UART0 while the schematic and SoC names this 583 * UART3. This is only for the informational lines i.e. "[FOO]", 584 * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only 585 * ones actually used for GPIO. 586 */ 587 588&msmgpio { 589 gpio-line-names = 590 "[UART0_TX]", /* GPIO_0, LSEC pin 5 */ 591 "[UART0_RX]", /* GPIO_1, LSEC pin 7 */ 592 "[UART0_CTS_N]", /* GPIO_2, LSEC pin 3 */ 593 "[UART0_RTS_N]", /* GPIO_3, LSEC pin 9 */ 594 "[UART1_TX]", /* GPIO_4, LSEC pin 11 */ 595 "[UART1_RX]", /* GPIO_5, LSEC pin 13 */ 596 "[I2C0_SDA]", /* GPIO_8, LSEC pin 17 */ 597 "[I2C0_SCL]", /* GPIO_7, LSEC pin 15 */ 598 "[SPI1_DOUT]", /* SPI1_MOSI, HSEC pin 1 */ 599 "[SPI1_DIN]", /* SPI1_MISO, HSEC pin 11 */ 600 "[SPI1_CS]", /* SPI1_CS_N, HSEC pin 7 */ 601 "[SPI1_SCLK]", /* SPI1_CLK, HSEC pin 9 */ 602 "GPIO-B", /* LS_EXP_GPIO_B, LSEC pin 24 */ 603 "GPIO-C", /* LS_EXP_GPIO_C, LSEC pin 25 */ 604 "[I2C3_SDA]", /* HSEC pin 38 */ 605 "[I2C3_SCL]", /* HSEC pin 36 */ 606 "[SPI0_MOSI]", /* LSEC pin 14 */ 607 "[SPI0_MISO]", /* LSEC pin 10 */ 608 "[SPI0_CS_N]", /* LSEC pin 12 */ 609 "[SPI0_CLK]", /* LSEC pin 8 */ 610 "HDMI_HPD_N", /* GPIO 20 */ 611 "USR_LED_1_CTRL", 612 "[I2C1_SDA]", /* GPIO_22, LSEC pin 21 */ 613 "[I2C1_SCL]", /* GPIO_23, LSEC pin 19 */ 614 "GPIO-G", /* LS_EXP_GPIO_G, LSEC pin 29 */ 615 "GPIO-H", /* LS_EXP_GPIO_H, LSEC pin 30 */ 616 "[CSI0_MCLK]", /* HSEC pin 15 */ 617 "[CSI1_MCLK]", /* HSEC pin 17 */ 618 "GPIO-K", /* LS_EXP_GPIO_K, LSEC pin 33 */ 619 "[I2C2_SDA]", /* HSEC pin 34 */ 620 "[I2C2_SCL]", /* HSEC pin 32 */ 621 "DSI2HDMI_INT_N", 622 "DSI_SW_SEL_APQ", 623 "GPIO-L", /* LS_EXP_GPIO_L, LSEC pin 34 */ 624 "GPIO-J", /* LS_EXP_GPIO_J, LSEC pin 32 */ 625 "GPIO-I", /* LS_EXP_GPIO_I, LSEC pin 31 */ 626 "GPIO-A", /* LS_EXP_GPIO_A, LSEC pin 23 */ 627 "FORCED_USB_BOOT", 628 "SD_CARD_DET_N", 629 "[WCSS_BT_SSBI]", 630 "[WCSS_WLAN_DATA_2]", /* GPIO 40 */ 631 "[WCSS_WLAN_DATA_1]", 632 "[WCSS_WLAN_DATA_0]", 633 "[WCSS_WLAN_SET]", 634 "[WCSS_WLAN_CLK]", 635 "[WCSS_FM_SSBI]", 636 "[WCSS_FM_SDI]", 637 "[WCSS_BT_DAT_CTL]", 638 "[WCSS_BT_DAT_STB]", 639 "NC", 640 "NC", /* GPIO 50 */ 641 "NC", 642 "NC", 643 "NC", 644 "NC", 645 "NC", 646 "NC", 647 "NC", 648 "NC", 649 "NC", 650 "NC", /* GPIO 60 */ 651 "NC", 652 "NC", 653 "[CDC_PDM0_CLK]", 654 "[CDC_PDM0_SYNC]", 655 "[CDC_PDM0_TX0]", 656 "[CDC_PDM0_RX0]", 657 "[CDC_PDM0_RX1]", 658 "[CDC_PDM0_RX2]", 659 "GPIO-D", /* LS_EXP_GPIO_D, LSEC pin 26 */ 660 "NC", /* GPIO 70 */ 661 "NC", 662 "NC", 663 "NC", 664 "NC", /* GPIO 74 */ 665 "NC", 666 "NC", 667 "NC", 668 "NC", 669 "NC", 670 "BOOT_CONFIG_0", /* GPIO 80 */ 671 "BOOT_CONFIG_1", 672 "BOOT_CONFIG_2", 673 "BOOT_CONFIG_3", 674 "NC", 675 "NC", 676 "BOOT_CONFIG_5", 677 "NC", 678 "NC", 679 "NC", 680 "NC", /* GPIO 90 */ 681 "NC", 682 "NC", 683 "NC", 684 "NC", 685 "NC", 686 "NC", 687 "NC", 688 "NC", 689 "NC", 690 "NC", /* GPIO 100 */ 691 "NC", 692 "NC", 693 "NC", 694 "SSBI_GPS", 695 "NC", 696 "NC", 697 "KEY_VOLP_N", 698 "NC", 699 "NC", 700 "[LS_EXP_MI2S_WS]", /* GPIO 110 */ 701 "NC", 702 "NC", 703 "[LS_EXP_MI2S_SCK]", 704 "[LS_EXP_MI2S_DATA0]", 705 "GPIO-E", /* LS_EXP_GPIO_E, LSEC pin 27 */ 706 "NC", 707 "[DSI2HDMI_MI2S_WS]", 708 "[DSI2HDMI_MI2S_SCK]", 709 "[DSI2HDMI_MI2S_DATA0]", 710 "USR_LED_2_CTRL", /* GPIO 120 */ 711 "SB_HS_ID"; 712 713 msmgpio_leds: msmgpio-leds { 714 pins = "gpio21", "gpio120"; 715 function = "gpio"; 716 717 output-low; 718 }; 719 720 usb_id_default: usb-id-default { 721 pins = "gpio121"; 722 function = "gpio"; 723 724 drive-strength = <8>; 725 input-enable; 726 bias-pull-up; 727 }; 728 729 adv7533_int_active: adv533-int-active { 730 pins = "gpio31"; 731 function = "gpio"; 732 733 drive-strength = <16>; 734 bias-disable; 735 }; 736 737 adv7533_int_suspend: adv7533-int-suspend { 738 pins = "gpio31"; 739 function = "gpio"; 740 741 drive-strength = <2>; 742 bias-disable; 743 }; 744 745 adv7533_switch_active: adv7533-switch-active { 746 pins = "gpio32"; 747 function = "gpio"; 748 749 drive-strength = <16>; 750 bias-disable; 751 }; 752 753 adv7533_switch_suspend: adv7533-switch-suspend { 754 pins = "gpio32"; 755 function = "gpio"; 756 757 drive-strength = <2>; 758 bias-disable; 759 }; 760 761 msm_key_volp_n_default: msm-key-volp-n-default { 762 pins = "gpio107"; 763 function = "gpio"; 764 765 drive-strength = <8>; 766 input-enable; 767 bias-pull-up; 768 }; 769}; 770 771&pm8916_gpios { 772 gpio-line-names = 773 "USR_LED_3_CTRL", 774 "USR_LED_4_CTRL", 775 "USB_HUB_RESET_N_PM", 776 "USB_SW_SEL_PM"; 777 778 usb_hub_reset_pm: usb-hub-reset-pm { 779 pins = "gpio3"; 780 function = PMIC_GPIO_FUNC_NORMAL; 781 782 input-disable; 783 output-high; 784 }; 785 786 usb_hub_reset_pm_device: usb-hub-reset-pm-device { 787 pins = "gpio3"; 788 function = PMIC_GPIO_FUNC_NORMAL; 789 790 output-low; 791 }; 792 793 usb_sw_sel_pm: usb-sw-sel-pm { 794 pins = "gpio4"; 795 function = PMIC_GPIO_FUNC_NORMAL; 796 797 power-source = <PM8916_GPIO_VPH>; 798 input-disable; 799 output-high; 800 }; 801 802 usb_sw_sel_pm_device: usb-sw-sel-pm-device { 803 pins = "gpio4"; 804 function = PMIC_GPIO_FUNC_NORMAL; 805 806 power-source = <PM8916_GPIO_VPH>; 807 input-disable; 808 output-low; 809 }; 810 811 pm8916_gpios_leds: pm8916-gpios-leds { 812 pins = "gpio1", "gpio2"; 813 function = PMIC_GPIO_FUNC_NORMAL; 814 815 output-low; 816 }; 817}; 818 819&pm8916_mpps { 820 gpio-line-names = 821 "VDD_PX_BIAS", 822 "WLAN_LED_CTRL", 823 "BT_LED_CTRL", 824 "GPIO-F"; /* LS_EXP_GPIO_F, LSEC pin 28 */ 825 826 pinctrl-names = "default"; 827 pinctrl-0 = <&ls_exp_gpio_f>; 828 829 ls_exp_gpio_f: pm8916-mpp4-state { 830 pins = "mpp4"; 831 function = "digital"; 832 833 output-low; 834 power-source = <PM8916_MPP_L5>; // 1.8V 835 }; 836 837 pm8916_mpps_leds: pm8916-mpps-state { 838 pins = "mpp2", "mpp3"; 839 function = "digital"; 840 841 output-low; 842 }; 843}; 844