1// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2/*
3 * Copyright (C) 2019 Marvell International Ltd.
4 *
5 * Device tree for the CN9130-DB board.
6 */
7
8#include "cn9130.dtsi"
9
10#include <dt-bindings/gpio/gpio.h>
11
12/ {
13	chosen {
14		stdout-path = "serial0:115200n8";
15	};
16
17	aliases {
18		gpio1 = &cp0_gpio1;
19		gpio2 = &cp0_gpio2;
20		i2c0 = &cp0_i2c0;
21		ethernet0 = &cp0_eth0;
22		ethernet1 = &cp0_eth1;
23		ethernet2 = &cp0_eth2;
24		spi1 = &cp0_spi0;
25		spi2 = &cp0_spi1;
26	};
27
28	memory@0 {
29		device_type = "memory";
30		reg = <0x0 0x0 0x0 0x80000000>;
31	};
32
33	ap0_reg_sd_vccq: ap0_sd_vccq@0 {
34		compatible = "regulator-gpio";
35		regulator-name = "ap0_sd_vccq";
36		regulator-min-microvolt = <1800000>;
37		regulator-max-microvolt = <3300000>;
38		gpios = <&expander0 8 GPIO_ACTIVE_HIGH>;
39		states = <1800000 0x1 3300000 0x0>;
40	};
41
42	cp0_reg_usb3_vbus0: cp0_usb3_vbus@0 {
43		compatible = "regulator-fixed";
44		regulator-name = "cp0-xhci0-vbus";
45		regulator-min-microvolt = <5000000>;
46		regulator-max-microvolt = <5000000>;
47		enable-active-high;
48		gpio = <&expander0 0 GPIO_ACTIVE_HIGH>;
49	};
50
51	cp0_usb3_0_phy0: cp0_usb3_phy@0 {
52		compatible = "usb-nop-xceiv";
53		vcc-supply = <&cp0_reg_usb3_vbus0>;
54	};
55
56	cp0_reg_usb3_vbus1: cp0_usb3_vbus@1 {
57		compatible = "regulator-fixed";
58		regulator-name = "cp0-xhci1-vbus";
59		regulator-min-microvolt = <5000000>;
60		regulator-max-microvolt = <5000000>;
61		enable-active-high;
62		gpio = <&expander0 1 GPIO_ACTIVE_HIGH>;
63	};
64
65	cp0_usb3_0_phy1: cp0_usb3_phy@1 {
66		compatible = "usb-nop-xceiv";
67		vcc-supply = <&cp0_reg_usb3_vbus1>;
68	};
69
70	cp0_reg_sd_vccq: cp0_sd_vccq@0 {
71		compatible = "regulator-gpio";
72		regulator-name = "cp0_sd_vccq";
73		regulator-min-microvolt = <1800000>;
74		regulator-max-microvolt = <3300000>;
75		gpios = <&expander0 15 GPIO_ACTIVE_HIGH>;
76		states = <1800000 0x1
77			  3300000 0x0>;
78	};
79
80	cp0_reg_sd_vcc: cp0_sd_vcc@0 {
81		compatible = "regulator-fixed";
82		regulator-name = "cp0_sd_vcc";
83		regulator-min-microvolt = <3300000>;
84		regulator-max-microvolt = <3300000>;
85		gpio = <&expander0 14 GPIO_ACTIVE_HIGH>;
86		enable-active-high;
87		regulator-always-on;
88	};
89
90	cp0_sfp_eth0: sfp-eth@0 {
91		compatible = "sff,sfp";
92		i2c-bus = <&cp0_sfpp0_i2c>;
93		los-gpios = <&cp0_module_expander1 11 GPIO_ACTIVE_HIGH>;
94		mod-def0-gpios = <&cp0_module_expander1 10 GPIO_ACTIVE_LOW>;
95		tx-disable-gpios = <&cp0_module_expander1 9 GPIO_ACTIVE_HIGH>;
96		tx-fault-gpios = <&cp0_module_expander1 8 GPIO_ACTIVE_HIGH>;
97		/*
98		 * SFP cages are unconnected on early PCBs because of an the I2C
99		 * lanes not being connected. Prevent the port for being
100		 * unusable by disabling the SFP node.
101		 */
102		status = "disabled";
103	};
104};
105
106&uart0 {
107	status = "okay";
108};
109
110/* on-board eMMC - U9 */
111&ap_sdhci0 {
112	pinctrl-names = "default";
113	bus-width = <8>;
114	vqmmc-supply = <&ap0_reg_sd_vccq>;
115	status = "okay";
116};
117
118&cp0_crypto {
119	status = "disabled";
120};
121
122&cp0_ethernet {
123	status = "okay";
124};
125
126/* SLM-1521-V2, CON9 */
127&cp0_eth0 {
128	status = "okay";
129	phy-mode = "10gbase-r";
130	/* Generic PHY, providing serdes lanes */
131	phys = <&cp0_comphy4 0>;
132	managed = "in-band-status";
133	sfp = <&cp0_sfp_eth0>;
134};
135
136/* CON56 */
137&cp0_eth1 {
138	status = "okay";
139	phy = <&phy0>;
140	phy-mode = "rgmii-id";
141};
142
143/* CON57 */
144&cp0_eth2 {
145	status = "okay";
146	phy = <&phy1>;
147	phy-mode = "rgmii-id";
148};
149
150&cp0_gpio1 {
151	status = "okay";
152};
153
154&cp0_gpio2 {
155	status = "okay";
156};
157
158&cp0_i2c0 {
159	status = "okay";
160	pinctrl-names = "default";
161	pinctrl-0 = <&cp0_i2c0_pins>;
162	clock-frequency = <100000>;
163
164	/* U36 */
165	expander0: pca953x@21 {
166		compatible = "nxp,pca9555";
167		pinctrl-names = "default";
168		gpio-controller;
169		#gpio-cells = <2>;
170		reg = <0x21>;
171		status = "okay";
172	};
173
174	/* U42 */
175	eeprom0: eeprom@50 {
176		compatible = "atmel,24c64";
177		reg = <0x50>;
178		pagesize = <0x20>;
179	};
180
181	/* U38 */
182	eeprom1: eeprom@57 {
183		compatible = "atmel,24c64";
184		reg = <0x57>;
185		pagesize = <0x20>;
186	};
187};
188
189&cp0_i2c1 {
190	status = "okay";
191	clock-frequency = <100000>;
192
193	/* SLM-1521-V2 - U3 */
194	i2c-mux@72 { /* verify address - depends on dpr */
195		compatible = "nxp,pca9544";
196		#address-cells = <1>;
197		#size-cells = <0>;
198		reg = <0x72>;
199		cp0_sfpp0_i2c: i2c@0 {
200			#address-cells = <1>;
201			#size-cells = <0>;
202			reg = <0>;
203		};
204
205		i2c@1 {
206			#address-cells = <1>;
207			#size-cells = <0>;
208			reg = <1>;
209			/* U12 */
210			cp0_module_expander1: pca9555@21 {
211				compatible = "nxp,pca9555";
212				pinctrl-names = "default";
213				gpio-controller;
214				#gpio-cells = <2>;
215				reg = <0x21>;
216			};
217
218		};
219	};
220};
221
222&cp0_mdio {
223	status = "okay";
224
225	phy0: ethernet-phy@0 {
226		reg = <0>;
227	};
228
229	phy1: ethernet-phy@1 {
230		reg = <1>;
231	};
232};
233
234/* U54 */
235&cp0_nand_controller {
236	status = "disabled";
237	pinctrl-names = "default";
238	pinctrl-0 = <&nand_pins &nand_rb>;
239
240	nand@0 {
241		reg = <0>;
242		label = "main-storage";
243		nand-rb = <0>;
244		nand-ecc-mode = "hw";
245		nand-on-flash-bbt;
246		nand-ecc-strength = <8>;
247		nand-ecc-step-size = <512>;
248
249		partitions {
250			compatible = "fixed-partitions";
251			#address-cells = <1>;
252			#size-cells = <1>;
253
254			partition@0 {
255				label = "U-Boot";
256				reg = <0 0x200000>;
257			};
258			partition@200000 {
259				label = "Linux";
260				reg = <0x200000 0xe00000>;
261			};
262			partition@1000000 {
263				label = "Filesystem";
264				reg = <0x1000000 0x3f000000>;
265			};
266		};
267	};
268};
269
270/* SLM-1521-V2, CON6 */
271&cp0_pcie0 {
272	status = "okay";
273	num-lanes = <4>;
274	num-viewport = <8>;
275	/* Generic PHY, providing serdes lanes */
276	phys = <&cp0_comphy0 0
277		&cp0_comphy1 0
278		&cp0_comphy2 0
279		&cp0_comphy3 0>;
280};
281
282&cp0_sata0 {
283	status = "okay";
284
285	/* SLM-1521-V2, CON2 */
286	sata-port@1 {
287		status = "okay";
288		/* Generic PHY, providing serdes lanes */
289		phys = <&cp0_comphy5 1>;
290	};
291};
292
293/* CON 28 */
294&cp0_sdhci0 {
295	status = "okay";
296	pinctrl-names = "default";
297	pinctrl-0 = <&cp0_sdhci_pins
298		     &cp0_sdhci_cd_pins>;
299	bus-width = <4>;
300	cd-gpios = <&cp0_gpio2 11 GPIO_ACTIVE_LOW>;
301	no-1-8-v;
302	vqmmc-supply = <&cp0_reg_sd_vccq>;
303	vmmc-supply = <&cp0_reg_sd_vcc>;
304};
305
306/* U55 */
307&cp0_spi1 {
308	status = "disabled";
309	pinctrl-names = "default";
310	pinctrl-0 = <&cp0_spi1_pins>;
311	reg = <0x700680 0x50>;
312
313	flash@0 {
314		#address-cells = <0x1>;
315		#size-cells = <0x1>;
316		compatible = "jedec,spi-nor";
317		reg = <0x0>;
318		/* On-board MUX does not allow higher frequencies */
319		spi-max-frequency = <40000000>;
320
321		partitions {
322			compatible = "fixed-partitions";
323			#address-cells = <1>;
324			#size-cells = <1>;
325
326			partition@0 {
327				label = "U-Boot-0";
328				reg = <0x0 0x200000>;
329			};
330
331			partition@400000 {
332				label = "Filesystem-0";
333				reg = <0x200000 0xe00000>;
334			};
335		};
336	};
337};
338
339&cp0_syscon0 {
340	cp0_pinctrl: pinctrl {
341		compatible = "marvell,cp115-standalone-pinctrl";
342
343		cp0_i2c0_pins: cp0-i2c-pins-0 {
344			marvell,pins = "mpp37", "mpp38";
345			marvell,function = "i2c0";
346		};
347		cp0_i2c1_pins: cp0-i2c-pins-1 {
348			marvell,pins = "mpp35", "mpp36";
349			marvell,function = "i2c1";
350		};
351		cp0_ge1_rgmii_pins: cp0-ge-rgmii-pins-0 {
352			marvell,pins = "mpp0", "mpp1", "mpp2",
353				       "mpp3", "mpp4", "mpp5",
354				       "mpp6", "mpp7", "mpp8",
355				       "mpp9", "mpp10", "mpp11";
356			marvell,function = "ge0";
357		};
358		cp0_ge2_rgmii_pins: cp0-ge-rgmii-pins-1 {
359			marvell,pins = "mpp44", "mpp45", "mpp46",
360				       "mpp47", "mpp48", "mpp49",
361				       "mpp50", "mpp51", "mpp52",
362				       "mpp53", "mpp54", "mpp55";
363			marvell,function = "ge1";
364		};
365		cp0_sdhci_cd_pins: cp0-sdhci-cd-pins-0 {
366			marvell,pins = "mpp43";
367			marvell,function = "gpio";
368		};
369		cp0_sdhci_pins: cp0-sdhi-pins-0 {
370			marvell,pins = "mpp56", "mpp57", "mpp58",
371				       "mpp59", "mpp60", "mpp61";
372			marvell,function = "sdio";
373		};
374		cp0_spi1_pins: cp0-spi-pins-1 {
375			marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
376			marvell,function = "spi1";
377		};
378		nand_pins: nand-pins {
379			marvell,pins = "mpp15", "mpp16", "mpp17", "mpp18",
380				       "mpp19", "mpp20", "mpp21", "mpp22",
381				       "mpp23", "mpp24", "mpp25", "mpp26",
382				       "mpp27";
383			marvell,function = "dev";
384		};
385		nand_rb: nand-rb {
386			marvell,pins = "mpp13";
387			marvell,function = "nf";
388		};
389	};
390};
391
392&cp0_utmi {
393	status = "okay";
394};
395
396&cp0_usb3_0 {
397	status = "okay";
398	usb-phy = <&cp0_usb3_0_phy0>;
399	phys = <&cp0_utmi0>;
400	phy-names = "utmi";
401	dr_mode = "host";
402};
403
404&cp0_usb3_1 {
405	status = "okay";
406	usb-phy = <&cp0_usb3_0_phy1>;
407	phys = <&cp0_utmi1>;
408	phy-names = "utmi";
409	dr_mode = "host";
410};
411