xref: /openbmc/linux/arch/arm64/boot/dts/freescale/imx8mm.dtsi (revision f403a26c)

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
 * Copyright 2019 NXP
 */

#include <dt-bindings/clock/imx8mm-clock.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/thermal/thermal.h>

#include "imx8mm-pinfunc.h"

/ {
	compatible = "fsl,imx8mm";
	interrupt-parent = <&gic>;
	#address-cells = <2>;
	#size-cells = <2>;

	aliases {
		ethernet0 = &fec1;
		i2c0 = &i2c1;
		i2c1 = &i2c2;
		i2c2 = &i2c3;
		i2c3 = &i2c4;
		serial0 = &uart1;
		serial1 = &uart2;
		serial2 = &uart3;
		serial3 = &uart4;
		spi0 = &ecspi1;
		spi1 = &ecspi2;
		spi2 = &ecspi3;
		mmc0 = &usdhc1;
		mmc1 = &usdhc2;
		mmc2 = &usdhc3;
		gpio0 = &gpio1;
		gpio1 = &gpio2;
		gpio2 = &gpio3;
		gpio3 = &gpio4;
		gpio4 = &gpio5;
	};

	cpus {
		#address-cells = <1>;
		#size-cells = <0>;

		A53_0: cpu@0 {
			device_type = "cpu";
			compatible = "arm,cortex-a53";
			reg = <0x0>;
			clock-latency = <61036>; /* two CLK32 periods */
			clocks = <&clk IMX8MM_CLK_ARM>;
			enable-method = "psci";
			next-level-cache = <&A53_L2>;
			operating-points-v2 = <&a53_opp_table>;
			nvmem-cells = <&cpu_speed_grade>;
			nvmem-cell-names = "speed_grade";
		};

		A53_1: cpu@1 {
			device_type = "cpu";
			compatible = "arm,cortex-a53";
			reg = <0x1>;
			clock-latency = <61036>; /* two CLK32 periods */
			clocks = <&clk IMX8MM_CLK_ARM>;
			enable-method = "psci";
			next-level-cache = <&A53_L2>;
			operating-points-v2 = <&a53_opp_table>;
		};

		A53_2: cpu@2 {
			device_type = "cpu";
			compatible = "arm,cortex-a53";
			reg = <0x2>;
			clock-latency = <61036>; /* two CLK32 periods */
			clocks = <&clk IMX8MM_CLK_ARM>;
			enable-method = "psci";
			next-level-cache = <&A53_L2>;
			operating-points-v2 = <&a53_opp_table>;
		};

		A53_3: cpu@3 {
			device_type = "cpu";
			compatible = "arm,cortex-a53";
			reg = <0x3>;
			clock-latency = <61036>; /* two CLK32 periods */
			clocks = <&clk IMX8MM_CLK_ARM>;
			enable-method = "psci";
			next-level-cache = <&A53_L2>;
			operating-points-v2 = <&a53_opp_table>;
		};

		A53_L2: l2-cache0 {
			compatible = "cache";
		};
	};

	a53_opp_table: opp-table {
		compatible = "operating-points-v2";
		opp-shared;

		opp-1200000000 {
			opp-hz = /bits/ 64 <1200000000>;
			opp-microvolt = <850000>;
			opp-supported-hw = <0xe>, <0x7>;
			clock-latency-ns = <150000>;
		};

		opp-1600000000 {
			opp-hz = /bits/ 64 <1600000000>;
			opp-microvolt = <900000>;
			opp-supported-hw = <0xc>, <0x7>;
			clock-latency-ns = <150000>;
		};

		opp-1800000000 {
			opp-hz = /bits/ 64 <1800000000>;
			opp-microvolt = <1000000>;
			/* Consumer only but rely on speed grading */
			opp-supported-hw = <0x8>, <0x7>;
			clock-latency-ns = <150000>;
		};
	};

	memory@40000000 {
		device_type = "memory";
		reg = <0x0 0x40000000 0 0x80000000>;
	};

	osc_32k: clock-osc-32k {
		compatible = "fixed-clock";
		#clock-cells = <0>;
		clock-frequency = <32768>;
		clock-output-names = "osc_32k";
	};

	osc_24m: clock-osc-24m {
		compatible = "fixed-clock";
		#clock-cells = <0>;
		clock-frequency = <24000000>;
		clock-output-names = "osc_24m";
	};

	clk_ext1: clock-ext1 {
		compatible = "fixed-clock";
		#clock-cells = <0>;
		clock-frequency = <133000000>;
		clock-output-names = "clk_ext1";
	};

	clk_ext2: clock-ext2 {
		compatible = "fixed-clock";
		#clock-cells = <0>;
		clock-frequency = <133000000>;
		clock-output-names = "clk_ext2";
	};

	clk_ext3: clock-ext3 {
		compatible = "fixed-clock";
		#clock-cells = <0>;
		clock-frequency = <133000000>;
		clock-output-names = "clk_ext3";
	};

	clk_ext4: clock-ext4 {
		compatible = "fixed-clock";
		#clock-cells = <0>;
		clock-frequency= <133000000>;
		clock-output-names = "clk_ext4";
	};

	gic: interrupt-controller@38800000 {
		compatible = "arm,gic-v3";
		reg = <0x0 0x38800000 0 0x10000>, /* GIC Dist */
		      <0x0 0x38880000 0 0xC0000>; /* GICR (RD_base + SGI_base) */
		#interrupt-cells = <3>;
		interrupt-controller;
		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
	};

	psci {
		compatible = "arm,psci-1.0";
		method = "smc";
	};

	pmu {
		compatible = "arm,armv8-pmuv3";
		interrupts = <GIC_PPI 7
			     (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_HIGH)>;
		interrupt-affinity = <&A53_0>, <&A53_1>, <&A53_2>, <&A53_3>;
	};

	timer {
		compatible = "arm,armv8-timer";
		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>, /* Physical Secure */
			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>, /* Physical Non-Secure */
			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>, /* Virtual */
			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>; /* Hypervisor */
		clock-frequency = <8000000>;
		arm,no-tick-in-suspend;
	};

	soc {
		compatible = "simple-bus";
		#address-cells = <1>;
		#size-cells = <1>;
		ranges = <0x0 0x0 0x0 0x3e000000>;

		aips1: bus@30000000 {
			compatible = "fsl,aips-bus", "simple-bus";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;

			gpio1: gpio@30200000 {
				compatible = "fsl,imx8mm-gpio", "fsl,imx35-gpio";
				reg = <0x30200000 0x10000>;
				interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
					     <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
				gpio-controller;
				#gpio-cells = <2>;
				interrupt-controller;
				#interrupt-cells = <2>;
			};

			gpio2: gpio@30210000 {
				compatible = "fsl,imx8mm-gpio", "fsl,imx35-gpio";
				reg = <0x30210000 0x10000>;
				interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
					     <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
				gpio-controller;
				#gpio-cells = <2>;
				interrupt-controller;
				#interrupt-cells = <2>;
			};

			gpio3: gpio@30220000 {
				compatible = "fsl,imx8mm-gpio", "fsl,imx35-gpio";
				reg = <0x30220000 0x10000>;
				interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
					     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
				gpio-controller;
				#gpio-cells = <2>;
				interrupt-controller;
				#interrupt-cells = <2>;
			};

			gpio4: gpio@30230000 {
				compatible = "fsl,imx8mm-gpio", "fsl,imx35-gpio";
				reg = <0x30230000 0x10000>;
				interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
					     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
				gpio-controller;
				#gpio-cells = <2>;
				interrupt-controller;
				#interrupt-cells = <2>;
			};

			gpio5: gpio@30240000 {
				compatible = "fsl,imx8mm-gpio", "fsl,imx35-gpio";
				reg = <0x30240000 0x10000>;
				interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
					     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
				gpio-controller;
				#gpio-cells = <2>;
				interrupt-controller;
				#interrupt-cells = <2>;
			};

			wdog1: watchdog@30280000 {
				compatible = "fsl,imx8mm-wdt", "fsl,imx21-wdt";
				reg = <0x30280000 0x10000>;
				interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_WDOG1_ROOT>;
				status = "disabled";
			};

			wdog2: watchdog@30290000 {
				compatible = "fsl,imx8mm-wdt", "fsl,imx21-wdt";
				reg = <0x30290000 0x10000>;
				interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_WDOG2_ROOT>;
				status = "disabled";
			};

			wdog3: watchdog@302a0000 {
				compatible = "fsl,imx8mm-wdt", "fsl,imx21-wdt";
				reg = <0x302a0000 0x10000>;
				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_WDOG3_ROOT>;
				status = "disabled";
			};

			sdma2: dma-controller@302c0000 {
				compatible = "fsl,imx8mm-sdma", "fsl,imx7d-sdma";
				reg = <0x302c0000 0x10000>;
				interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_SDMA2_ROOT>,
					 <&clk IMX8MM_CLK_SDMA2_ROOT>;
				clock-names = "ipg", "ahb";
				#dma-cells = <3>;
				fsl,sdma-ram-script-name = "imx/sdma/sdma-imx7d.bin";
			};

			sdma3: dma-controller@302b0000 {
				compatible = "fsl,imx8mm-sdma", "fsl,imx7d-sdma";
				reg = <0x302b0000 0x10000>;
				interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_SDMA3_ROOT>,
				 <&clk IMX8MM_CLK_SDMA3_ROOT>;
				clock-names = "ipg", "ahb";
				#dma-cells = <3>;
				fsl,sdma-ram-script-name = "imx/sdma/sdma-imx7d.bin";
			};

			iomuxc: pinctrl@30330000 {
				compatible = "fsl,imx8mm-iomuxc";
				reg = <0x30330000 0x10000>;
			};

			gpr: iomuxc-gpr@30340000 {
				compatible = "fsl,imx8mm-iomuxc-gpr", "syscon";
				reg = <0x30340000 0x10000>;
			};

			ocotp: ocotp-ctrl@30350000 {
				compatible = "fsl,imx8mm-ocotp", "fsl,imx7d-ocotp", "syscon";
				reg = <0x30350000 0x10000>;
				clocks = <&clk IMX8MM_CLK_OCOTP_ROOT>;
				/* For nvmem subnodes */
				#address-cells = <1>;
				#size-cells = <1>;

				cpu_speed_grade: speed-grade@10 {
					reg = <0x10 4>;
				};
			};

			anatop: anatop@30360000 {
				compatible = "fsl,imx8mm-anatop", "syscon", "simple-bus";
				reg = <0x30360000 0x10000>;
			};

			snvs: snvs@30370000 {
				compatible = "fsl,sec-v4.0-mon","syscon", "simple-mfd";
				reg = <0x30370000 0x10000>;

				snvs_rtc: snvs-rtc-lp {
					compatible = "fsl,sec-v4.0-mon-rtc-lp";
					regmap = <&snvs>;
					offset = <0x34>;
					interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
						     <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
				};

				snvs_pwrkey: snvs-powerkey {
					compatible = "fsl,sec-v4.0-pwrkey";
					regmap = <&snvs>;
					interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
					linux,keycode = <KEY_POWER>;
					wakeup-source;
				};
			};

			clk: clock-controller@30380000 {
				compatible = "fsl,imx8mm-ccm";
				reg = <0x30380000 0x10000>;
				#clock-cells = <1>;
				clocks = <&osc_32k>, <&osc_24m>, <&clk_ext1>, <&clk_ext2>,
					 <&clk_ext3>, <&clk_ext4>;
				clock-names = "osc_32k", "osc_24m", "clk_ext1", "clk_ext2",
					      "clk_ext3", "clk_ext4";
			};

			src: reset-controller@30390000 {
				compatible = "fsl,imx8mm-src", "syscon";
				reg = <0x30390000 0x10000>;
				interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
				#reset-cells = <1>;
			};
		};

		aips2: bus@30400000 {
			compatible = "fsl,aips-bus", "simple-bus";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;

			pwm1: pwm@30660000 {
				compatible = "fsl,imx8mm-pwm", "fsl,imx27-pwm";
				reg = <0x30660000 0x10000>;
				interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_PWM1_ROOT>,
					<&clk IMX8MM_CLK_PWM1_ROOT>;
				clock-names = "ipg", "per";
				#pwm-cells = <2>;
				status = "disabled";
			};

			pwm2: pwm@30670000 {
				compatible = "fsl,imx8mm-pwm", "fsl,imx27-pwm";
				reg = <0x30670000 0x10000>;
				interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_PWM2_ROOT>,
					 <&clk IMX8MM_CLK_PWM2_ROOT>;
				clock-names = "ipg", "per";
				#pwm-cells = <2>;
				status = "disabled";
			};

			pwm3: pwm@30680000 {
				compatible = "fsl,imx8mm-pwm", "fsl,imx27-pwm";
				reg = <0x30680000 0x10000>;
				interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_PWM3_ROOT>,
					 <&clk IMX8MM_CLK_PWM3_ROOT>;
				clock-names = "ipg", "per";
				#pwm-cells = <2>;
				status = "disabled";
			};

			pwm4: pwm@30690000 {
				compatible = "fsl,imx8mm-pwm", "fsl,imx27-pwm";
				reg = <0x30690000 0x10000>;
				interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_PWM4_ROOT>,
					 <&clk IMX8MM_CLK_PWM4_ROOT>;
				clock-names = "ipg", "per";
				#pwm-cells = <2>;
				status = "disabled";
			};
		};

		aips3: bus@30800000 {
			compatible = "fsl,aips-bus", "simple-bus";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;

			ecspi1: spi@30820000 {
				compatible = "fsl,imx8mm-ecspi", "fsl,imx51-ecspi";
				#address-cells = <1>;
				#size-cells = <0>;
				reg = <0x30820000 0x10000>;
				interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_ECSPI1_ROOT>,
					 <&clk IMX8MM_CLK_ECSPI1_ROOT>;
				clock-names = "ipg", "per";
				dmas = <&sdma1 0 7 1>, <&sdma1 1 7 2>;
				dma-names = "rx", "tx";
				status = "disabled";
			};

			ecspi2: spi@30830000 {
				compatible = "fsl,imx8mm-ecspi", "fsl,imx51-ecspi";
				#address-cells = <1>;
				#size-cells = <0>;
				reg = <0x30830000 0x10000>;
				interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_ECSPI2_ROOT>,
					 <&clk IMX8MM_CLK_ECSPI2_ROOT>;
				clock-names = "ipg", "per";
				dmas = <&sdma1 2 7 1>, <&sdma1 3 7 2>;
				dma-names = "rx", "tx";
				status = "disabled";
			};

			ecspi3: spi@30840000 {
				compatible = "fsl,imx8mm-ecspi", "fsl,imx51-ecspi";
				#address-cells = <1>;
				#size-cells = <0>;
				reg = <0x30840000 0x10000>;
				interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_ECSPI3_ROOT>,
					 <&clk IMX8MM_CLK_ECSPI3_ROOT>;
				clock-names = "ipg", "per";
				dmas = <&sdma1 4 7 1>, <&sdma1 5 7 2>;
				dma-names = "rx", "tx";
				status = "disabled";
			};

			uart1: serial@30860000 {
				compatible = "fsl,imx8mm-uart", "fsl,imx6q-uart";
				reg = <0x30860000 0x10000>;
				interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_UART1_ROOT>,
					 <&clk IMX8MM_CLK_UART1_ROOT>;
				clock-names = "ipg", "per";
				dmas = <&sdma1 22 4 0>, <&sdma1 23 4 0>;
				dma-names = "rx", "tx";
				status = "disabled";
			};

			uart3: serial@30880000 {
				compatible = "fsl,imx8mm-uart", "fsl,imx6q-uart";
				reg = <0x30880000 0x10000>;
				interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_UART3_ROOT>,
					 <&clk IMX8MM_CLK_UART3_ROOT>;
				clock-names = "ipg", "per";
				dmas = <&sdma1 26 4 0>, <&sdma1 27 4 0>;
				dma-names = "rx", "tx";
				status = "disabled";
			};

			uart2: serial@30890000 {
				compatible = "fsl,imx8mm-uart", "fsl,imx6q-uart";
				reg = <0x30890000 0x10000>;
				interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_UART2_ROOT>,
					 <&clk IMX8MM_CLK_UART2_ROOT>;
				clock-names = "ipg", "per";
				status = "disabled";
			};

			i2c1: i2c@30a20000 {
				compatible = "fsl,imx8mm-i2c", "fsl,imx21-i2c";
				#address-cells = <1>;
				#size-cells = <0>;
				reg = <0x30a20000 0x10000>;
				interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_I2C1_ROOT>;
				status = "disabled";
			};

			i2c2: i2c@30a30000 {
				compatible = "fsl,imx8mm-i2c", "fsl,imx21-i2c";
				#address-cells = <1>;
				#size-cells = <0>;
				reg = <0x30a30000 0x10000>;
				interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_I2C2_ROOT>;
				status = "disabled";
			};

			i2c3: i2c@30a40000 {
				#address-cells = <1>;
				#size-cells = <0>;
				compatible = "fsl,imx8mm-i2c", "fsl,imx21-i2c";
				reg = <0x30a40000 0x10000>;
				interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_I2C3_ROOT>;
				status = "disabled";
			};

			i2c4: i2c@30a50000 {
				compatible = "fsl,imx8mm-i2c", "fsl,imx21-i2c";
				#address-cells = <1>;
				#size-cells = <0>;
				reg = <0x30a50000 0x10000>;
				interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_I2C4_ROOT>;
				status = "disabled";
			};

			uart4: serial@30a60000 {
				compatible = "fsl,imx8mm-uart", "fsl,imx6q-uart";
				reg = <0x30a60000 0x10000>;
				interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_UART4_ROOT>,
					 <&clk IMX8MM_CLK_UART4_ROOT>;
				clock-names = "ipg", "per";
				dmas = <&sdma1 28 4 0>, <&sdma1 29 4 0>;
				dma-names = "rx", "tx";
				status = "disabled";
			};

			usdhc1: mmc@30b40000 {
				compatible = "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc";
				reg = <0x30b40000 0x10000>;
				interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_DUMMY>,
					 <&clk IMX8MM_CLK_NAND_USDHC_BUS>,
					 <&clk IMX8MM_CLK_USDHC1_ROOT>;
				clock-names = "ipg", "ahb", "per";
				assigned-clocks = <&clk IMX8MM_CLK_USDHC1>;
				assigned-clock-rates = <400000000>;
				fsl,tuning-start-tap = <20>;
				fsl,tuning-step= <2>;
				bus-width = <4>;
				status = "disabled";
			};

			usdhc2: mmc@30b50000 {
				compatible = "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc";
				reg = <0x30b50000 0x10000>;
				interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_DUMMY>,
					 <&clk IMX8MM_CLK_NAND_USDHC_BUS>,
					 <&clk IMX8MM_CLK_USDHC2_ROOT>;
				clock-names = "ipg", "ahb", "per";
				fsl,tuning-start-tap = <20>;
				fsl,tuning-step= <2>;
				bus-width = <4>;
				status = "disabled";
			};

			usdhc3: mmc@30b60000 {
				compatible = "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc";
				reg = <0x30b60000 0x10000>;
				interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_DUMMY>,
					 <&clk IMX8MM_CLK_NAND_USDHC_BUS>,
					 <&clk IMX8MM_CLK_USDHC3_ROOT>;
				clock-names = "ipg", "ahb", "per";
				assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>;
				assigned-clock-rates = <400000000>;
				fsl,tuning-start-tap = <20>;
				fsl,tuning-step= <2>;
				bus-width = <4>;
				status = "disabled";
			};

			sdma1: dma-controller@30bd0000 {
				compatible = "fsl,imx8mm-sdma", "fsl,imx7d-sdma";
				reg = <0x30bd0000 0x10000>;
				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_SDMA1_ROOT>,
					 <&clk IMX8MM_CLK_SDMA1_ROOT>;
				clock-names = "ipg", "ahb";
				#dma-cells = <3>;
				fsl,sdma-ram-script-name = "imx/sdma/sdma-imx7d.bin";
			};

			fec1: ethernet@30be0000 {
				compatible = "fsl,imx8mm-fec", "fsl,imx6sx-fec";
				reg = <0x30be0000 0x10000>;
				interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
					     <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>,
					     <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_ENET1_ROOT>,
					 <&clk IMX8MM_CLK_ENET1_ROOT>,
					 <&clk IMX8MM_CLK_ENET_TIMER>,
					 <&clk IMX8MM_CLK_ENET_REF>,
					 <&clk IMX8MM_CLK_ENET_PHY_REF>;
				clock-names = "ipg", "ahb", "ptp",
					      "enet_clk_ref", "enet_out";
				assigned-clocks = <&clk IMX8MM_CLK_ENET_AXI>,
						  <&clk IMX8MM_CLK_ENET_TIMER>,
						  <&clk IMX8MM_CLK_ENET_REF>,
						  <&clk IMX8MM_CLK_ENET_TIMER>;
				assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_266M>,
							 <&clk IMX8MM_SYS_PLL2_100M>,
							 <&clk IMX8MM_SYS_PLL2_125M>;
				assigned-clock-rates = <0>, <0>, <125000000>, <100000000>;
				fsl,num-tx-queues = <3>;
				fsl,num-rx-queues = <3>;
				status = "disabled";
			};

		};

		aips4: bus@32c00000 {
			compatible = "fsl,aips-bus", "simple-bus";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges;

			usbotg1: usb@32e40000 {
				compatible = "fsl,imx8mm-usb", "fsl,imx7d-usb";
				reg = <0x32e40000 0x200>;
				interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_USB1_CTRL_ROOT>;
				clock-names = "usb1_ctrl_root_clk";
				assigned-clocks = <&clk IMX8MM_CLK_USB_BUS>,
						  <&clk IMX8MM_CLK_USB_CORE_REF>;
				assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>,
							 <&clk IMX8MM_SYS_PLL1_100M>;
				fsl,usbphy = <&usbphynop1>;
				fsl,usbmisc = <&usbmisc1 0>;
				status = "disabled";
			};

			usbphynop1: usbphynop1 {
				compatible = "usb-nop-xceiv";
				clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
				assigned-clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
				assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_100M>;
				clock-names = "main_clk";
			};

			usbmisc1: usbmisc@32e40200 {
				compatible = "fsl,imx8mm-usbmisc", "fsl,imx7d-usbmisc";
				#index-cells = <1>;
				reg = <0x32e40200 0x200>;
			};

			usbotg2: usb@32e50000 {
				compatible = "fsl,imx8mm-usb", "fsl,imx7d-usb";
				reg = <0x32e50000 0x200>;
				interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
				clocks = <&clk IMX8MM_CLK_USB1_CTRL_ROOT>;
				clock-names = "usb1_ctrl_root_clk";
				assigned-clocks = <&clk IMX8MM_CLK_USB_BUS>,
						  <&clk IMX8MM_CLK_USB_CORE_REF>;
				assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>,
							 <&clk IMX8MM_SYS_PLL1_100M>;
				fsl,usbphy = <&usbphynop2>;
				fsl,usbmisc = <&usbmisc2 0>;
				status = "disabled";
			};

			usbphynop2: usbphynop2 {
				compatible = "usb-nop-xceiv";
				clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
				assigned-clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
				assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_100M>;
				clock-names = "main_clk";
			};

			usbmisc2: usbmisc@32e50200 {
				compatible = "fsl,imx8mm-usbmisc", "fsl,imx7d-usbmisc";
				#index-cells = <1>;
				reg = <0x32e50200 0x200>;
			};

		};

		dma_apbh: dma-controller@33000000 {
			compatible = "fsl,imx7d-dma-apbh", "fsl,imx28-dma-apbh";
			reg = <0x33000000 0x2000>;
			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3";
			#dma-cells = <1>;
			dma-channels = <4>;
			clocks = <&clk IMX8MM_CLK_NAND_USDHC_BUS_RAWNAND_CLK>;
		};

		gpmi: nand-controller@33002000{
			compatible = "fsl,imx8mm-gpmi-nand", "fsl,imx7d-gpmi-nand";
			#address-cells = <1>;
			#size-cells = <1>;
			reg = <0x33002000 0x2000>, <0x33004000 0x4000>;
			reg-names = "gpmi-nand", "bch";
			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "bch";
			clocks = <&clk IMX8MM_CLK_NAND_ROOT>,
				 <&clk IMX8MM_CLK_NAND_USDHC_BUS_RAWNAND_CLK>;
			clock-names = "gpmi_io", "gpmi_bch_apb";
			dmas = <&dma_apbh 0>;
			dma-names = "rx-tx";
			status = "disabled";
		};
	};
};