1// SPDX-License-Identifier: GPL-2.0-or-later OR MIT 2/* 3 * Copyright 2022 Toradex 4 */ 5 6#include "dt-bindings/phy/phy-imx8-pcie.h" 7#include "dt-bindings/pwm/pwm.h" 8#include "imx8mm.dtsi" 9 10/ { 11 chosen { 12 stdout-path = &uart1; 13 }; 14 15 aliases { 16 rtc0 = &rtc_i2c; 17 rtc1 = &snvs_rtc; 18 }; 19 20 backlight: backlight { 21 compatible = "pwm-backlight"; 22 brightness-levels = <0 45 63 88 119 158 203 255>; 23 default-brightness-level = <4>; 24 /* Verdin I2S_2_D_OUT (DSI_1_BKL_EN/DSI_1_BKL_EN_LVDS, SODIMM 46) */ 25 enable-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>; 26 pinctrl-names = "default"; 27 pinctrl-0 = <&pinctrl_i2s_2_d_out_dsi_1_bkl_en>; 28 power-supply = <®_3p3v>; 29 /* Verdin PWM_3_DSI/PWM_3_DSI_LVDS (SODIMM 19) */ 30 pwms = <&pwm1 0 6666667 PWM_POLARITY_INVERTED>; 31 status = "disabled"; 32 }; 33 34 /* Fixed clock dedicated to SPI CAN controller */ 35 clk40m: oscillator { 36 compatible = "fixed-clock"; 37 #clock-cells = <0>; 38 clock-frequency = <40000000>; 39 }; 40 41 gpio-keys { 42 compatible = "gpio-keys"; 43 pinctrl-names = "default"; 44 pinctrl-0 = <&pinctrl_gpio_keys>; 45 46 key-wakeup { 47 debounce-interval = <10>; 48 /* Verdin CTRL_WAKE1_MICO# (SODIMM 252) */ 49 gpios = <&gpio4 28 GPIO_ACTIVE_LOW>; 50 label = "Wake-Up"; 51 linux,code = <KEY_WAKEUP>; 52 wakeup-source; 53 }; 54 }; 55 56 /* Carrier Board Supplies */ 57 reg_1p8v: regulator-1p8v { 58 compatible = "regulator-fixed"; 59 regulator-max-microvolt = <1800000>; 60 regulator-min-microvolt = <1800000>; 61 regulator-name = "+V1.8_SW"; 62 }; 63 64 reg_3p3v: regulator-3p3v { 65 compatible = "regulator-fixed"; 66 regulator-max-microvolt = <3300000>; 67 regulator-min-microvolt = <3300000>; 68 regulator-name = "+V3.3_SW"; 69 }; 70 71 reg_5p0v: regulator-5p0v { 72 compatible = "regulator-fixed"; 73 regulator-max-microvolt = <5000000>; 74 regulator-min-microvolt = <5000000>; 75 regulator-name = "+V5_SW"; 76 }; 77 78 /* Non PMIC On-module Supplies */ 79 reg_ethphy: regulator-ethphy { 80 compatible = "regulator-fixed"; 81 enable-active-high; 82 gpio = <&gpio2 20 GPIO_ACTIVE_HIGH>; /* PMIC_EN_ETH */ 83 off-on-delay = <500000>; 84 pinctrl-names = "default"; 85 pinctrl-0 = <&pinctrl_reg_eth>; 86 regulator-boot-on; 87 regulator-max-microvolt = <3300000>; 88 regulator-min-microvolt = <3300000>; 89 regulator-name = "On-module +V3.3_ETH"; 90 startup-delay-us = <200000>; 91 }; 92 93 reg_usb_otg1_vbus: regulator-usb-otg1 { 94 compatible = "regulator-fixed"; 95 enable-active-high; 96 /* Verdin USB_1_EN (SODIMM 155) */ 97 gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; 98 pinctrl-names = "default"; 99 pinctrl-0 = <&pinctrl_reg_usb1_en>; 100 regulator-max-microvolt = <5000000>; 101 regulator-min-microvolt = <5000000>; 102 regulator-name = "USB_1_EN"; 103 }; 104 105 reg_usb_otg2_vbus: regulator-usb-otg2 { 106 compatible = "regulator-fixed"; 107 enable-active-high; 108 /* Verdin USB_2_EN (SODIMM 185) */ 109 gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>; 110 pinctrl-names = "default"; 111 pinctrl-0 = <&pinctrl_reg_usb2_en>; 112 regulator-max-microvolt = <5000000>; 113 regulator-min-microvolt = <5000000>; 114 regulator-name = "USB_2_EN"; 115 }; 116 117 reg_usdhc2_vmmc: regulator-usdhc2 { 118 compatible = "regulator-fixed"; 119 enable-active-high; 120 /* Verdin SD_1_PWR_EN (SODIMM 76) */ 121 gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>; 122 off-on-delay = <100000>; 123 pinctrl-names = "default"; 124 pinctrl-0 = <&pinctrl_usdhc2_pwr_en>; 125 regulator-max-microvolt = <3300000>; 126 regulator-min-microvolt = <3300000>; 127 regulator-name = "+V3.3_SD"; 128 startup-delay-us = <2000>; 129 }; 130 131 reserved-memory { 132 #address-cells = <2>; 133 #size-cells = <2>; 134 ranges; 135 136 /* Use the kernel configuration settings instead */ 137 /delete-node/ linux,cma; 138 }; 139}; 140 141&A53_0 { 142 cpu-supply = <®_vdd_arm>; 143}; 144 145&A53_1 { 146 cpu-supply = <®_vdd_arm>; 147}; 148 149&A53_2 { 150 cpu-supply = <®_vdd_arm>; 151}; 152 153&A53_3 { 154 cpu-supply = <®_vdd_arm>; 155}; 156 157&cpu_alert0 { 158 temperature = <95000>; 159}; 160 161&cpu_crit0 { 162 temperature = <105000>; 163}; 164 165&ddrc { 166 operating-points-v2 = <&ddrc_opp_table>; 167 168 ddrc_opp_table: opp-table { 169 compatible = "operating-points-v2"; 170 171 opp-25M { 172 opp-hz = /bits/ 64 <25000000>; 173 }; 174 175 opp-100M { 176 opp-hz = /bits/ 64 <100000000>; 177 }; 178 179 opp-750M { 180 opp-hz = /bits/ 64 <750000000>; 181 }; 182 }; 183}; 184 185/* Verdin SPI_1 */ 186&ecspi2 { 187 #address-cells = <1>; 188 #size-cells = <0>; 189 cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>; 190 pinctrl-names = "default"; 191 pinctrl-0 = <&pinctrl_ecspi2>; 192}; 193 194/* Verdin CAN_1 (On-module) */ 195&ecspi3 { 196 #address-cells = <1>; 197 #size-cells = <0>; 198 cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>; 199 pinctrl-names = "default"; 200 pinctrl-0 = <&pinctrl_ecspi3>; 201 status = "okay"; 202 203 can1: can@0 { 204 compatible = "microchip,mcp251xfd"; 205 clocks = <&clk40m>; 206 interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_LOW>; 207 pinctrl-names = "default"; 208 pinctrl-0 = <&pinctrl_can1_int>; 209 reg = <0>; 210 spi-max-frequency = <8500000>; 211 }; 212}; 213 214/* Verdin ETH_1 (On-module PHY) */ 215&fec1 { 216 fsl,magic-packet; 217 phy-handle = <ðphy0>; 218 phy-mode = "rgmii-id"; 219 phy-supply = <®_ethphy>; 220 pinctrl-names = "default", "sleep"; 221 pinctrl-0 = <&pinctrl_fec1>; 222 pinctrl-1 = <&pinctrl_fec1_sleep>; 223 224 mdio { 225 #address-cells = <1>; 226 #size-cells = <0>; 227 228 ethphy0: ethernet-phy@7 { 229 compatible = "ethernet-phy-ieee802.3-c22"; 230 interrupt-parent = <&gpio1>; 231 interrupts = <10 IRQ_TYPE_LEVEL_LOW>; 232 micrel,led-mode = <0>; 233 reg = <7>; 234 }; 235 }; 236}; 237 238/* Verdin QSPI_1 */ 239&flexspi { 240 pinctrl-names = "default"; 241 pinctrl-0 = <&pinctrl_flexspi0>; 242}; 243 244&gpio1 { 245 gpio-line-names = "SODIMM_216", 246 "SODIMM_19", 247 "", 248 "", 249 "", 250 "", 251 "", 252 "", 253 "SODIMM_220", 254 "SODIMM_222", 255 "", 256 "SODIMM_218", 257 "SODIMM_155", 258 "SODIMM_157", 259 "SODIMM_185", 260 "SODIMM_187"; 261}; 262 263&gpio2 { 264 gpio-line-names = "", 265 "", 266 "", 267 "", 268 "", 269 "", 270 "", 271 "", 272 "", 273 "", 274 "", 275 "", 276 "SODIMM_84", 277 "SODIMM_78", 278 "SODIMM_74", 279 "SODIMM_80", 280 "SODIMM_82", 281 "SODIMM_70", 282 "SODIMM_72"; 283}; 284 285&gpio5 { 286 gpio-line-names = "SODIMM_131", 287 "", 288 "SODIMM_91", 289 "SODIMM_16", 290 "SODIMM_15", 291 "SODIMM_208", 292 "SODIMM_137", 293 "SODIMM_139", 294 "SODIMM_141", 295 "SODIMM_143", 296 "SODIMM_196", 297 "SODIMM_200", 298 "SODIMM_198", 299 "SODIMM_202", 300 "", 301 "", 302 "SODIMM_55", 303 "SODIMM_53", 304 "SODIMM_95", 305 "SODIMM_93", 306 "SODIMM_14", 307 "SODIMM_12", 308 "", 309 "", 310 "", 311 "", 312 "SODIMM_210", 313 "SODIMM_212", 314 "SODIMM_151", 315 "SODIMM_153"; 316 317 ctrl-sleep-moci-hog { 318 gpio-hog; 319 /* Verdin CTRL_SLEEP_MOCI# (SODIMM 256) */ 320 gpios = <1 GPIO_ACTIVE_HIGH>; 321 line-name = "CTRL_SLEEP_MOCI#"; 322 output-high; 323 pinctrl-names = "default"; 324 pinctrl-0 = <&pinctrl_ctrl_sleep_moci>; 325 }; 326}; 327 328/* On-module I2C */ 329&i2c1 { 330 clock-frequency = <400000>; 331 pinctrl-names = "default", "gpio"; 332 pinctrl-0 = <&pinctrl_i2c1>; 333 pinctrl-1 = <&pinctrl_i2c1_gpio>; 334 scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 335 sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 336 status = "okay"; 337 338 pca9450: pmic@25 { 339 compatible = "nxp,pca9450a"; 340 interrupt-parent = <&gpio1>; 341 /* PMIC PCA9450 PMIC_nINT GPIO1_IO3 */ 342 interrupts = <3 IRQ_TYPE_LEVEL_LOW>; 343 pinctrl-names = "default"; 344 pinctrl-0 = <&pinctrl_pmic>; 345 reg = <0x25>; 346 sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; 347 348 /* 349 * The bootloader is expected to switch on the I2C level shifter for the TLA2024 ADC 350 * behind this PMIC. 351 */ 352 353 regulators { 354 reg_vdd_soc: BUCK1 { 355 nxp,dvs-run-voltage = <850000>; 356 nxp,dvs-standby-voltage = <800000>; 357 regulator-always-on; 358 regulator-boot-on; 359 regulator-max-microvolt = <850000>; 360 regulator-min-microvolt = <800000>; 361 regulator-name = "On-module +VDD_SOC (BUCK1)"; 362 regulator-ramp-delay = <3125>; 363 }; 364 365 reg_vdd_arm: BUCK2 { 366 nxp,dvs-run-voltage = <950000>; 367 nxp,dvs-standby-voltage = <850000>; 368 regulator-always-on; 369 regulator-boot-on; 370 regulator-max-microvolt = <950000>; 371 regulator-min-microvolt = <850000>; 372 regulator-name = "On-module +VDD_ARM (BUCK2)"; 373 regulator-ramp-delay = <3125>; 374 }; 375 376 reg_vdd_dram: BUCK3 { 377 regulator-always-on; 378 regulator-boot-on; 379 regulator-max-microvolt = <950000>; 380 regulator-min-microvolt = <850000>; 381 regulator-name = "On-module +VDD_GPU_VPU_DDR (BUCK3)"; 382 }; 383 384 reg_vdd_3v3: BUCK4 { 385 regulator-always-on; 386 regulator-boot-on; 387 regulator-max-microvolt = <3300000>; 388 regulator-min-microvolt = <3300000>; 389 regulator-name = "On-module +V3.3 (BUCK4)"; 390 }; 391 392 reg_vdd_1v8: BUCK5 { 393 regulator-always-on; 394 regulator-boot-on; 395 regulator-max-microvolt = <1800000>; 396 regulator-min-microvolt = <1800000>; 397 regulator-name = "PWR_1V8_MOCI (BUCK5)"; 398 }; 399 400 reg_nvcc_dram: BUCK6 { 401 regulator-always-on; 402 regulator-boot-on; 403 regulator-max-microvolt = <1100000>; 404 regulator-min-microvolt = <1100000>; 405 regulator-name = "On-module +VDD_DDR (BUCK6)"; 406 }; 407 408 reg_nvcc_snvs: LDO1 { 409 regulator-always-on; 410 regulator-boot-on; 411 regulator-max-microvolt = <1800000>; 412 regulator-min-microvolt = <1800000>; 413 regulator-name = "On-module +V1.8_SNVS (LDO1)"; 414 }; 415 416 reg_vdd_snvs: LDO2 { 417 regulator-always-on; 418 regulator-boot-on; 419 regulator-max-microvolt = <900000>; 420 regulator-min-microvolt = <800000>; 421 regulator-name = "On-module +V0.8_SNVS (LDO2)"; 422 }; 423 424 reg_vdda: LDO3 { 425 regulator-always-on; 426 regulator-boot-on; 427 regulator-max-microvolt = <1800000>; 428 regulator-min-microvolt = <1800000>; 429 regulator-name = "On-module +V1.8A (LDO3)"; 430 }; 431 432 reg_vdd_phy: LDO4 { 433 regulator-always-on; 434 regulator-boot-on; 435 regulator-max-microvolt = <900000>; 436 regulator-min-microvolt = <900000>; 437 regulator-name = "On-module +V0.9_MIPI (LDO4)"; 438 }; 439 440 reg_nvcc_sd: LDO5 { 441 regulator-max-microvolt = <3300000>; 442 regulator-min-microvolt = <1800000>; 443 regulator-name = "On-module +V3.3_1.8_SD (LDO5)"; 444 }; 445 }; 446 }; 447 448 rtc_i2c: rtc@32 { 449 compatible = "epson,rx8130"; 450 reg = <0x32>; 451 }; 452 453 adc@49 { 454 compatible = "ti,ads1015"; 455 reg = <0x49>; 456 #address-cells = <1>; 457 #size-cells = <0>; 458 459 /* Verdin I2C_1 (ADC_4 - ADC_3) */ 460 channel@0 { 461 reg = <0>; 462 ti,datarate = <4>; 463 ti,gain = <2>; 464 }; 465 466 /* Verdin I2C_1 (ADC_4 - ADC_1) */ 467 channel@1 { 468 reg = <1>; 469 ti,datarate = <4>; 470 ti,gain = <2>; 471 }; 472 473 /* Verdin I2C_1 (ADC_3 - ADC_1) */ 474 channel@2 { 475 reg = <2>; 476 ti,datarate = <4>; 477 ti,gain = <2>; 478 }; 479 480 /* Verdin I2C_1 (ADC_2 - ADC_1) */ 481 channel@3 { 482 reg = <3>; 483 ti,datarate = <4>; 484 ti,gain = <2>; 485 }; 486 487 /* Verdin I2C_1 ADC_4 */ 488 channel@4 { 489 reg = <4>; 490 ti,datarate = <4>; 491 ti,gain = <2>; 492 }; 493 494 /* Verdin I2C_1 ADC_3 */ 495 channel@5 { 496 reg = <5>; 497 ti,datarate = <4>; 498 ti,gain = <2>; 499 }; 500 501 /* Verdin I2C_1 ADC_2 */ 502 channel@6 { 503 reg = <6>; 504 ti,datarate = <4>; 505 ti,gain = <2>; 506 }; 507 508 /* Verdin I2C_1 ADC_1 */ 509 channel@7 { 510 reg = <7>; 511 ti,datarate = <4>; 512 ti,gain = <2>; 513 }; 514 }; 515 516 eeprom@50 { 517 compatible = "st,24c02"; 518 pagesize = <16>; 519 reg = <0x50>; 520 }; 521}; 522 523/* Verdin I2C_2_DSI */ 524&i2c2 { 525 clock-frequency = <10000>; 526 pinctrl-names = "default", "gpio"; 527 pinctrl-0 = <&pinctrl_i2c2>; 528 pinctrl-1 = <&pinctrl_i2c2_gpio>; 529 scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 530 sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 531 status = "disabled"; 532}; 533 534/* Verdin I2C_3_HDMI N/A */ 535 536/* Verdin I2C_4_CSI */ 537&i2c3 { 538 clock-frequency = <400000>; 539 pinctrl-names = "default", "gpio"; 540 pinctrl-0 = <&pinctrl_i2c3>; 541 pinctrl-1 = <&pinctrl_i2c3_gpio>; 542 scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 543 sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 544}; 545 546/* Verdin I2C_1 */ 547&i2c4 { 548 clock-frequency = <400000>; 549 pinctrl-names = "default", "gpio"; 550 pinctrl-0 = <&pinctrl_i2c4>; 551 pinctrl-1 = <&pinctrl_i2c4_gpio>; 552 scl-gpios = <&gpio5 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 553 sda-gpios = <&gpio5 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 554 555 gpio_expander_21: gpio-expander@21 { 556 compatible = "nxp,pcal6416"; 557 #gpio-cells = <2>; 558 gpio-controller; 559 reg = <0x21>; 560 vcc-supply = <®_3p3v>; 561 status = "disabled"; 562 }; 563 564 lvds_ti_sn65dsi83: bridge@2c { 565 compatible = "ti,sn65dsi83"; 566 /* Verdin GPIO_9_DSI (SN65DSI84 IRQ, SODIMM 17, unused) */ 567 /* Verdin GPIO_10_DSI (SODIMM 21) */ 568 enable-gpios = <&gpio3 3 GPIO_ACTIVE_HIGH>; 569 pinctrl-names = "default"; 570 pinctrl-0 = <&pinctrl_gpio_10_dsi>; 571 reg = <0x2c>; 572 status = "disabled"; 573 }; 574 575 /* Current measurement into module VCC */ 576 hwmon: hwmon@40 { 577 compatible = "ti,ina219"; 578 reg = <0x40>; 579 shunt-resistor = <10000>; 580 status = "disabled"; 581 }; 582 583 hdmi_lontium_lt8912: hdmi@48 { 584 compatible = "lontium,lt8912b"; 585 pinctrl-names = "default"; 586 pinctrl-0 = <&pinctrl_gpio_10_dsi>, <&pinctrl_pwm_3_dsi_hpd_gpio>; 587 reg = <0x48>; 588 /* Verdin GPIO_9_DSI (LT8912 INT, SODIMM 17, unused) */ 589 /* Verdin GPIO_10_DSI (SODIMM 21) */ 590 reset-gpios = <&gpio3 3 GPIO_ACTIVE_LOW>; 591 status = "disabled"; 592 }; 593 594 atmel_mxt_ts: touch@4a { 595 compatible = "atmel,maxtouch"; 596 /* 597 * Verdin GPIO_9_DSI 598 * (TOUCH_INT#, SODIMM 17, also routed to SN65DSI83 IRQ albeit currently unused) 599 */ 600 interrupt-parent = <&gpio3>; 601 interrupts = <15 IRQ_TYPE_EDGE_FALLING>; 602 pinctrl-names = "default"; 603 pinctrl-0 = <&pinctrl_gpio_9_dsi>, <&pinctrl_i2s_2_bclk_touch_reset>; 604 reg = <0x4a>; 605 /* Verdin I2S_2_BCLK (TOUCH_RESET#, SODIMM 42) */ 606 reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>; 607 status = "disabled"; 608 }; 609 610 /* Temperature sensor on carrier board */ 611 hwmon_temp: sensor@4f { 612 compatible = "ti,tmp75c"; 613 reg = <0x4f>; 614 status = "disabled"; 615 }; 616 617 /* EEPROM on display adapter (MIPI DSI Display Adapter) */ 618 eeprom_display_adapter: eeprom@50 { 619 compatible = "st,24c02"; 620 pagesize = <16>; 621 reg = <0x50>; 622 status = "disabled"; 623 }; 624 625 /* EEPROM on carrier board */ 626 eeprom_carrier_board: eeprom@57 { 627 compatible = "st,24c02"; 628 pagesize = <16>; 629 reg = <0x57>; 630 status = "disabled"; 631 }; 632}; 633 634/* Verdin PCIE_1 */ 635&pcie0 { 636 assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>, 637 <&clk IMX8MM_CLK_PCIE1_CTRL>; 638 assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>, 639 <&clk IMX8MM_SYS_PLL2_250M>; 640 assigned-clock-rates = <10000000>, <250000000>; 641 clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>, 642 <&clk IMX8MM_CLK_PCIE1_PHY>; 643 clock-names = "pcie", "pcie_aux", "pcie_bus"; 644 pinctrl-names = "default"; 645 pinctrl-0 = <&pinctrl_pcie0>; 646 /* PCIE_1_RESET# (SODIMM 244) */ 647 reset-gpio = <&gpio3 19 GPIO_ACTIVE_LOW>; 648}; 649 650&pcie_phy { 651 clocks = <&clk IMX8MM_CLK_PCIE1_PHY>; 652 fsl,clkreq-unsupported; 653 fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_OUTPUT>; 654 fsl,tx-deemph-gen1 = <0x2d>; 655 fsl,tx-deemph-gen2 = <0xf>; 656}; 657 658/* Verdin PWM_3_DSI */ 659&pwm1 { 660 pinctrl-names = "default"; 661 pinctrl-0 = <&pinctrl_pwm_1>; 662 #pwm-cells = <3>; 663}; 664 665/* Verdin PWM_1 */ 666&pwm2 { 667 pinctrl-names = "default"; 668 pinctrl-0 = <&pinctrl_pwm_2>; 669 #pwm-cells = <3>; 670}; 671 672/* Verdin PWM_2 */ 673&pwm3 { 674 pinctrl-names = "default"; 675 pinctrl-0 = <&pinctrl_pwm_3>; 676 #pwm-cells = <3>; 677}; 678 679/* Verdin I2S_1 */ 680&sai2 { 681 #sound-dai-cells = <0>; 682 assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>; 683 assigned-clock-rates = <24576000>; 684 assigned-clocks = <&clk IMX8MM_CLK_SAI2>; 685 pinctrl-names = "default"; 686 pinctrl-0 = <&pinctrl_sai2>; 687}; 688 689&snvs_pwrkey { 690 status = "okay"; 691}; 692 693/* Verdin UART_3, used as the Linux console */ 694&uart1 { 695 pinctrl-names = "default"; 696 pinctrl-0 = <&pinctrl_uart1>; 697}; 698 699/* Verdin UART_1 */ 700&uart2 { 701 pinctrl-names = "default"; 702 pinctrl-0 = <&pinctrl_uart2>; 703 uart-has-rtscts; 704}; 705 706/* Verdin UART_2 */ 707&uart3 { 708 pinctrl-names = "default"; 709 pinctrl-0 = <&pinctrl_uart3>; 710 uart-has-rtscts; 711}; 712 713/* 714 * Verdin UART_4 715 * Resource allocated to M4 by default, must not be accessed from Cortex-A35 or you get an OOPS 716 */ 717&uart4 { 718 pinctrl-names = "default"; 719 pinctrl-0 = <&pinctrl_uart4>; 720}; 721 722/* Verdin USB_1 */ 723&usbotg1 { 724 adp-disable; 725 dr_mode = "otg"; 726 hnp-disable; 727 over-current-active-low; 728 samsung,picophy-dc-vol-level-adjust = <7>; 729 samsung,picophy-pre-emp-curr-control = <3>; 730 srp-disable; 731 vbus-supply = <®_usb_otg1_vbus>; 732}; 733 734/* Verdin USB_2 */ 735&usbotg2 { 736 dr_mode = "host"; 737 over-current-active-low; 738 samsung,picophy-dc-vol-level-adjust = <7>; 739 samsung,picophy-pre-emp-curr-control = <3>; 740 vbus-supply = <®_usb_otg2_vbus>; 741}; 742 743&usbphynop1 { 744 vcc-supply = <®_vdd_3v3>; 745}; 746 747&usbphynop2 { 748 power-domains = <&pgc_otg2>; 749 vcc-supply = <®_vdd_3v3>; 750}; 751 752/* On-module eMMC */ 753&usdhc1 { 754 bus-width = <8>; 755 keep-power-in-suspend; 756 non-removable; 757 pinctrl-names = "default", "state_100mhz", "state_200mhz"; 758 pinctrl-0 = <&pinctrl_usdhc1>; 759 pinctrl-1 = <&pinctrl_usdhc1_100mhz>; 760 pinctrl-2 = <&pinctrl_usdhc1_200mhz>; 761 status = "okay"; 762}; 763 764/* Verdin SD_1 */ 765&usdhc2 { 766 bus-width = <4>; 767 cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; 768 disable-wp; 769 pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep"; 770 pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_cd>; 771 pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_cd>; 772 pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_cd>; 773 pinctrl-3 = <&pinctrl_usdhc2_sleep>, <&pinctrl_usdhc2_cd_sleep>; 774 vmmc-supply = <®_usdhc2_vmmc>; 775}; 776 777&wdog1 { 778 fsl,ext-reset-output; 779 pinctrl-names = "default"; 780 pinctrl-0 = <&pinctrl_wdog>; 781 status = "okay"; 782}; 783 784&iomuxc { 785 pinctrl-names = "default"; 786 pinctrl-0 = <&pinctrl_gpio1>, <&pinctrl_gpio2>, 787 <&pinctrl_gpio3>, <&pinctrl_gpio4>, 788 <&pinctrl_gpio7>, <&pinctrl_gpio8>, 789 <&pinctrl_gpio_hog1>, <&pinctrl_gpio_hog2>, <&pinctrl_gpio_hog3>, 790 <&pinctrl_pmic_tpm_ena>; 791 792 pinctrl_can1_int: can1intgrp { 793 fsl,pins = 794 <MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x146>; /* CAN_1_SPI_INT#_1.8V */ 795 }; 796 797 pinctrl_can2_int: can2intgrp { 798 fsl,pins = 799 <MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x106>; /* CAN_2_SPI_INT#_1.8V, unused */ 800 }; 801 802 pinctrl_ctrl_sleep_moci: ctrlsleepmocigrp { 803 fsl,pins = 804 <MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1 0x106>; /* SODIMM 256 */ 805 }; 806 807 pinctrl_ecspi2: ecspi2grp { 808 fsl,pins = 809 <MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x6>, /* SODIMM 198 */ 810 <MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x6>, /* SODIMM 200 */ 811 <MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x6>, /* SODIMM 196 */ 812 <MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x6>; /* SODIMM 202 */ 813 }; 814 815 pinctrl_ecspi3: ecspi3grp { 816 fsl,pins = 817 <MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x146>, /* CAN_2_SPI_CS#_1.8V */ 818 <MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK 0x6>, /* CAN_SPI_SCK_1.8V */ 819 <MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI 0x6>, /* CAN_SPI_MOSI_1.8V */ 820 <MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO 0x6>, /* CAN_SPI_MISO_1.8V */ 821 <MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25 0x6>; /* CAN_1_SPI_CS_1.8V# */ 822 }; 823 824 pinctrl_fec1: fec1grp { 825 fsl,pins = 826 <MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3>, 827 <MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3>, 828 <MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91>, 829 <MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91>, 830 <MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91>, 831 <MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91>, 832 <MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91>, 833 <MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91>, 834 <MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f>, 835 <MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f>, 836 <MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f>, 837 <MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f>, 838 <MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f>, 839 <MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f>, 840 <MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x146>; 841 }; 842 843 pinctrl_fec1_sleep: fec1-sleepgrp { 844 fsl,pins = 845 <MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3>, 846 <MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3>, 847 <MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91>, 848 <MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91>, 849 <MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91>, 850 <MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91>, 851 <MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91>, 852 <MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91>, 853 <MX8MM_IOMUXC_ENET_TD0_GPIO1_IO21 0x1f>, 854 <MX8MM_IOMUXC_ENET_TD1_GPIO1_IO20 0x1f>, 855 <MX8MM_IOMUXC_ENET_TD2_GPIO1_IO19 0x1f>, 856 <MX8MM_IOMUXC_ENET_TD3_GPIO1_IO18 0x1f>, 857 <MX8MM_IOMUXC_ENET_TXC_GPIO1_IO23 0x1f>, 858 <MX8MM_IOMUXC_ENET_TX_CTL_GPIO1_IO22 0x1f>, 859 <MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10 0x106>; 860 }; 861 862 pinctrl_flexspi0: flexspi0grp { 863 fsl,pins = 864 <MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x106>, /* SODIMM 52 */ 865 <MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x106>, /* SODIMM 54 */ 866 <MX8MM_IOMUXC_NAND_CE1_B_QSPI_A_SS1_B 0x106>, /* SODIMM 64 */ 867 <MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x106>, /* SODIMM 56 */ 868 <MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x106>, /* SODIMM 58 */ 869 <MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x106>, /* SODIMM 60 */ 870 <MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x106>, /* SODIMM 62 */ 871 <MX8MM_IOMUXC_NAND_DQS_QSPI_A_DQS 0x106>; /* SODIMM 66 */ 872 }; 873 874 pinctrl_gpio1: gpio1grp { 875 fsl,pins = 876 <MX8MM_IOMUXC_NAND_CE3_B_GPIO3_IO4 0x106>; /* SODIMM 206 */ 877 }; 878 879 pinctrl_gpio2: gpio2grp { 880 fsl,pins = 881 <MX8MM_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5 0x106>; /* SODIMM 208 */ 882 }; 883 884 pinctrl_gpio3: gpio3grp { 885 fsl,pins = 886 <MX8MM_IOMUXC_UART3_RXD_GPIO5_IO26 0x106>; /* SODIMM 210 */ 887 }; 888 889 pinctrl_gpio4: gpio4grp { 890 fsl,pins = 891 <MX8MM_IOMUXC_UART3_TXD_GPIO5_IO27 0x106>; /* SODIMM 212 */ 892 }; 893 894 pinctrl_gpio5: gpio5grp { 895 fsl,pins = 896 <MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x106>; /* SODIMM 216 */ 897 }; 898 899 pinctrl_gpio6: gpio6grp { 900 fsl,pins = 901 <MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x106>; /* SODIMM 218 */ 902 }; 903 904 pinctrl_gpio7: gpio7grp { 905 fsl,pins = 906 <MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x106>; /* SODIMM 220 */ 907 }; 908 909 pinctrl_gpio8: gpio8grp { 910 fsl,pins = 911 <MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x106>; /* SODIMM 222 */ 912 }; 913 914 /* Verdin GPIO_9_DSI (pulled-up as active-low) */ 915 pinctrl_gpio_9_dsi: gpio9dsigrp { 916 fsl,pins = 917 <MX8MM_IOMUXC_NAND_RE_B_GPIO3_IO15 0x146>; /* SODIMM 17 */ 918 }; 919 920 /* Verdin GPIO_10_DSI (pulled-up as active-low) */ 921 pinctrl_gpio_10_dsi: gpio10dsigrp { 922 fsl,pins = 923 <MX8MM_IOMUXC_NAND_CE2_B_GPIO3_IO3 0x146>; /* SODIMM 21 */ 924 }; 925 926 pinctrl_gpio_hog1: gpiohog1grp { 927 fsl,pins = 928 <MX8MM_IOMUXC_SAI1_MCLK_GPIO4_IO20 0x106>, /* SODIMM 88 */ 929 <MX8MM_IOMUXC_SAI1_RXC_GPIO4_IO1 0x106>, /* SODIMM 90 */ 930 <MX8MM_IOMUXC_SAI1_RXD0_GPIO4_IO2 0x106>, /* SODIMM 92 */ 931 <MX8MM_IOMUXC_SAI1_RXD1_GPIO4_IO3 0x106>, /* SODIMM 94 */ 932 <MX8MM_IOMUXC_SAI1_RXD2_GPIO4_IO4 0x106>, /* SODIMM 96 */ 933 <MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5 0x106>, /* SODIMM 100 */ 934 <MX8MM_IOMUXC_SAI1_RXFS_GPIO4_IO0 0x106>, /* SODIMM 102 */ 935 <MX8MM_IOMUXC_SAI1_TXC_GPIO4_IO11 0x106>, /* SODIMM 104 */ 936 <MX8MM_IOMUXC_SAI1_TXD0_GPIO4_IO12 0x106>, /* SODIMM 106 */ 937 <MX8MM_IOMUXC_SAI1_TXD1_GPIO4_IO13 0x106>, /* SODIMM 108 */ 938 <MX8MM_IOMUXC_SAI1_TXD2_GPIO4_IO14 0x106>, /* SODIMM 112 */ 939 <MX8MM_IOMUXC_SAI1_TXD3_GPIO4_IO15 0x106>, /* SODIMM 114 */ 940 <MX8MM_IOMUXC_SAI1_TXD4_GPIO4_IO16 0x106>, /* SODIMM 116 */ 941 <MX8MM_IOMUXC_SAI1_TXD6_GPIO4_IO18 0x106>, /* SODIMM 118 */ 942 <MX8MM_IOMUXC_SAI1_TXFS_GPIO4_IO10 0x106>; /* SODIMM 120 */ 943 }; 944 945 pinctrl_gpio_hog2: gpiohog2grp { 946 fsl,pins = 947 <MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2 0x106>; /* SODIMM 91 */ 948 }; 949 950 pinctrl_gpio_hog3: gpiohog3grp { 951 fsl,pins = 952 <MX8MM_IOMUXC_GPIO1_IO13_GPIO1_IO13 0x146>, /* SODIMM 157 */ 953 <MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x146>; /* SODIMM 187 */ 954 }; 955 956 pinctrl_gpio_keys: gpiokeysgrp { 957 fsl,pins = 958 <MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28 0x146>; /* SODIMM 252 */ 959 }; 960 961 /* On-module I2C */ 962 pinctrl_i2c1: i2c1grp { 963 fsl,pins = 964 <MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x40000146>, /* PMIC_I2C_SCL */ 965 <MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x40000146>; /* PMIC_I2C_SDA */ 966 }; 967 968 pinctrl_i2c1_gpio: i2c1gpiogrp { 969 fsl,pins = 970 <MX8MM_IOMUXC_I2C1_SCL_GPIO5_IO14 0x146>, /* PMIC_I2C_SCL */ 971 <MX8MM_IOMUXC_I2C1_SDA_GPIO5_IO15 0x146>; /* PMIC_I2C_SDA */ 972 }; 973 974 /* Verdin I2C_4_CSI */ 975 pinctrl_i2c2: i2c2grp { 976 fsl,pins = 977 <MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x40000146>, /* SODIMM 55 */ 978 <MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x40000146>; /* SODIMM 53 */ 979 }; 980 981 pinctrl_i2c2_gpio: i2c2gpiogrp { 982 fsl,pins = 983 <MX8MM_IOMUXC_I2C2_SCL_GPIO5_IO16 0x146>, /* SODIMM 55 */ 984 <MX8MM_IOMUXC_I2C2_SDA_GPIO5_IO17 0x146>; /* SODIMM 53 */ 985 }; 986 987 /* Verdin I2C_2_DSI */ 988 pinctrl_i2c3: i2c3grp { 989 fsl,pins = 990 <MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x40000146>, /* SODIMM 95 */ 991 <MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x40000146>; /* SODIMM 93 */ 992 }; 993 994 pinctrl_i2c3_gpio: i2c3gpiogrp { 995 fsl,pins = 996 <MX8MM_IOMUXC_I2C3_SCL_GPIO5_IO18 0x146>, /* SODIMM 95 */ 997 <MX8MM_IOMUXC_I2C3_SDA_GPIO5_IO19 0x146>; /* SODIMM 93 */ 998 }; 999 1000 /* Verdin I2C_1 */ 1001 pinctrl_i2c4: i2c4grp { 1002 fsl,pins = 1003 <MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x40000146>, /* SODIMM 14 */ 1004 <MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x40000146>; /* SODIMM 12 */ 1005 }; 1006 1007 pinctrl_i2c4_gpio: i2c4gpiogrp { 1008 fsl,pins = 1009 <MX8MM_IOMUXC_I2C4_SCL_GPIO5_IO20 0x146>, /* SODIMM 14 */ 1010 <MX8MM_IOMUXC_I2C4_SDA_GPIO5_IO21 0x146>; /* SODIMM 12 */ 1011 }; 1012 1013 /* Verdin I2S_2_BCLK (TOUCH_RESET#) */ 1014 pinctrl_i2s_2_bclk_touch_reset: i2s2bclktouchresetgrp { 1015 fsl,pins = 1016 <MX8MM_IOMUXC_SAI5_RXD2_GPIO3_IO23 0x6>; /* SODIMM 42 */ 1017 }; 1018 1019 /* Verdin I2S_2_D_OUT shared with SAI5 */ 1020 pinctrl_i2s_2_d_out_dsi_1_bkl_en: i2s2doutdsi1bklengrp { 1021 fsl,pins = 1022 <MX8MM_IOMUXC_SAI5_RXD3_GPIO3_IO24 0x6>; /* SODIMM 46 */ 1023 }; 1024 1025 pinctrl_pcie0: pcie0grp { 1026 fsl,pins = 1027 <MX8MM_IOMUXC_SAI5_RXFS_GPIO3_IO19 0x6>, /* SODIMM 244 */ 1028 /* PMIC_EN_PCIe_CLK, unused */ 1029 <MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x6>; 1030 }; 1031 1032 pinctrl_pmic: pmicirqgrp { 1033 fsl,pins = 1034 <MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x141>; /* PMIC_INT# */ 1035 }; 1036 1037 /* Verdin PWM_3_DSI shared with GPIO1_IO1 */ 1038 pinctrl_pwm_1: pwm1grp { 1039 fsl,pins = 1040 <MX8MM_IOMUXC_GPIO1_IO01_PWM1_OUT 0x6>; /* SODIMM 19 */ 1041 }; 1042 1043 pinctrl_pwm_2: pwm2grp { 1044 fsl,pins = 1045 <MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT 0x6>; /* SODIMM 15 */ 1046 }; 1047 1048 pinctrl_pwm_3: pwm3grp { 1049 fsl,pins = 1050 <MX8MM_IOMUXC_SPDIF_TX_PWM3_OUT 0x6>; /* SODIMM 16 */ 1051 }; 1052 1053 /* Verdin PWM_3_DSI (pulled-down as active-high) shared with PWM1_OUT */ 1054 pinctrl_pwm_3_dsi_hpd_gpio: pwm3dsihpdgpiogrp { 1055 fsl,pins = 1056 <MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x106>; /* SODIMM 19 */ 1057 }; 1058 1059 pinctrl_reg_eth: regethgrp { 1060 fsl,pins = 1061 <MX8MM_IOMUXC_SD2_WP_GPIO2_IO20 0x146>; /* PMIC_EN_ETH */ 1062 }; 1063 1064 pinctrl_reg_usb1_en: regusb1engrp { 1065 fsl,pins = 1066 <MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x106>; /* SODIMM 155 */ 1067 }; 1068 1069 pinctrl_reg_usb2_en: regusb2engrp { 1070 fsl,pins = 1071 <MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14 0x106>; /* SODIMM 185 */ 1072 }; 1073 1074 pinctrl_sai2: sai2grp { 1075 fsl,pins = 1076 <MX8MM_IOMUXC_SAI2_MCLK_SAI2_MCLK 0x6>, /* SODIMM 38 */ 1077 <MX8MM_IOMUXC_SAI2_TXC_SAI2_TX_BCLK 0x6>, /* SODIMM 30 */ 1078 <MX8MM_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC 0x6>, /* SODIMM 32 */ 1079 <MX8MM_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0 0x6>, /* SODIMM 36 */ 1080 <MX8MM_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0 0x6>; /* SODIMM 34 */ 1081 }; 1082 1083 pinctrl_sai5: sai5grp { 1084 fsl,pins = 1085 <MX8MM_IOMUXC_SAI5_RXD0_SAI5_RX_DATA0 0x6>, /* SODIMM 48 */ 1086 <MX8MM_IOMUXC_SAI5_RXD1_SAI5_TX_SYNC 0x6>, /* SODIMM 44 */ 1087 <MX8MM_IOMUXC_SAI5_RXD2_SAI5_TX_BCLK 0x6>, /* SODIMM 42 */ 1088 <MX8MM_IOMUXC_SAI5_RXD3_SAI5_TX_DATA0 0x6>; /* SODIMM 46 */ 1089 }; 1090 1091 /* control signal for optional ATTPM20P or SE050 */ 1092 pinctrl_pmic_tpm_ena: pmictpmenagrp { 1093 fsl,pins = 1094 <MX8MM_IOMUXC_SAI1_TXD7_GPIO4_IO19 0x106>; /* PMIC_TPM_ENA */ 1095 }; 1096 1097 pinctrl_tsp: tspgrp { 1098 fsl,pins = 1099 <MX8MM_IOMUXC_SAI1_RXD4_GPIO4_IO6 0x6>, /* SODIMM 148 */ 1100 <MX8MM_IOMUXC_SAI1_RXD5_GPIO4_IO7 0x6>, /* SODIMM 152 */ 1101 <MX8MM_IOMUXC_SAI1_RXD6_GPIO4_IO8 0x6>, /* SODIMM 154 */ 1102 <MX8MM_IOMUXC_SAI1_RXD7_GPIO4_IO9 0x146>, /* SODIMM 174 */ 1103 <MX8MM_IOMUXC_SAI1_TXD5_GPIO4_IO17 0x6>; /* SODIMM 150 */ 1104 }; 1105 1106 pinctrl_uart1: uart1grp { 1107 fsl,pins = 1108 <MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX 0x146>, /* SODIMM 147 */ 1109 <MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX 0x146>; /* SODIMM 149 */ 1110 }; 1111 1112 pinctrl_uart2: uart2grp { 1113 fsl,pins = 1114 <MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B 0x146>, /* SODIMM 133 */ 1115 <MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B 0x146>, /* SODIMM 135 */ 1116 <MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX 0x146>, /* SODIMM 131 */ 1117 <MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX 0x146>; /* SODIMM 129 */ 1118 }; 1119 1120 pinctrl_uart3: uart3grp { 1121 fsl,pins = 1122 <MX8MM_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B 0x146>, /* SODIMM 141 */ 1123 <MX8MM_IOMUXC_ECSPI1_MOSI_UART3_DCE_TX 0x146>, /* SODIMM 139 */ 1124 <MX8MM_IOMUXC_ECSPI1_SCLK_UART3_DCE_RX 0x146>, /* SODIMM 137 */ 1125 <MX8MM_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B 0x146>; /* SODIMM 143 */ 1126 }; 1127 1128 pinctrl_uart4: uart4grp { 1129 fsl,pins = 1130 <MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x146>, /* SODIMM 151 */ 1131 <MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x146>; /* SODIMM 153 */ 1132 }; 1133 1134 pinctrl_usdhc1: usdhc1grp { 1135 fsl,pins = 1136 <MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190>, 1137 <MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0>, 1138 <MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0>, 1139 <MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0>, 1140 <MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0>, 1141 <MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0>, 1142 <MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d0>, 1143 <MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d0>, 1144 <MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d0>, 1145 <MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d0>, 1146 <MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x1d1>, 1147 <MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x190>; 1148 }; 1149 1150 pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp { 1151 fsl,pins = 1152 <MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x194>, 1153 <MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4>, 1154 <MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4>, 1155 <MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4>, 1156 <MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4>, 1157 <MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4>, 1158 <MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d4>, 1159 <MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d4>, 1160 <MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d4>, 1161 <MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d4>, 1162 <MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x1d1>, 1163 <MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x194>; 1164 }; 1165 1166 pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp { 1167 fsl,pins = 1168 <MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x196>, 1169 <MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6>, 1170 <MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6>, 1171 <MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6>, 1172 <MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6>, 1173 <MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6>, 1174 <MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d6>, 1175 <MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d6>, 1176 <MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d6>, 1177 <MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d6>, 1178 <MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0x1d1>, 1179 <MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x196>; 1180 }; 1181 1182 pinctrl_usdhc2_cd: usdhc2cdgrp { 1183 fsl,pins = 1184 <MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x6>; /* SODIMM 84 */ 1185 }; 1186 1187 pinctrl_usdhc2_cd_sleep: usdhc2cdslpgrp { 1188 fsl,pins = 1189 <MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x0>; /* SODIMM 84 */ 1190 }; 1191 1192 pinctrl_usdhc2_pwr_en: usdhc2pwrengrp { 1193 fsl,pins = 1194 <MX8MM_IOMUXC_NAND_CLE_GPIO3_IO5 0x6>; /* SODIMM 76 */ 1195 }; 1196 1197 /* 1198 * Note: Due to ERR050080 we use discrete external on-module resistors pulling-up to the 1199 * on-module +V3.3_1.8_SD (LDO5) rail and explicitly disable the internal pull-ups here. 1200 */ 1201 pinctrl_usdhc2: usdhc2grp { 1202 fsl,pins = 1203 <MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x10>, 1204 <MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x90>, /* SODIMM 78 */ 1205 <MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x90>, /* SODIMM 74 */ 1206 <MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x90>, /* SODIMM 80 */ 1207 <MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x90>, /* SODIMM 82 */ 1208 <MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x90>, /* SODIMM 70 */ 1209 <MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x90>; /* SODIMM 72 */ 1210 }; 1211 1212 pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { 1213 fsl,pins = 1214 <MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x10>, 1215 <MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x94>, 1216 <MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x94>, 1217 <MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x94>, 1218 <MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x94>, 1219 <MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x94>, 1220 <MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x94>; 1221 }; 1222 1223 pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { 1224 fsl,pins = 1225 <MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x10>, 1226 <MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x96>, 1227 <MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x96>, 1228 <MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x96>, 1229 <MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x96>, 1230 <MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x96>, 1231 <MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x96>; 1232 }; 1233 1234 /* Avoid backfeeding with removed card power */ 1235 pinctrl_usdhc2_sleep: usdhc2slpgrp { 1236 fsl,pins = 1237 <MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x0>, 1238 <MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x0>, 1239 <MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x0>, 1240 <MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x0>, 1241 <MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x0>, 1242 <MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x0>, 1243 <MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x0>; 1244 }; 1245 1246 /* 1247 * On-module Wi-Fi/BT or type specific SDHC interface 1248 * (e.g. on X52 extension slot of Verdin Development Board) 1249 */ 1250 pinctrl_usdhc3: usdhc3grp { 1251 fsl,pins = 1252 <MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x150>, 1253 <MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x150>, 1254 <MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x150>, 1255 <MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x150>, 1256 <MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x150>, 1257 <MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x150>; 1258 }; 1259 1260 pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp { 1261 fsl,pins = 1262 <MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x154>, 1263 <MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x154>, 1264 <MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x154>, 1265 <MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x154>, 1266 <MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x154>, 1267 <MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x154>; 1268 }; 1269 1270 pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp { 1271 fsl,pins = 1272 <MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x156>, 1273 <MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x156>, 1274 <MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x156>, 1275 <MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x156>, 1276 <MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x156>, 1277 <MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x156>; 1278 }; 1279 1280 pinctrl_wdog: wdoggrp { 1281 fsl,pins = 1282 <MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x166>; /* PMIC_WDI */ 1283 }; 1284 1285 pinctrl_wifi_ctrl: wifictrlgrp { 1286 fsl,pins = 1287 <MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x46>, /* WIFI_WKUP_BT */ 1288 <MX8MM_IOMUXC_SAI1_RXD7_GPIO4_IO9 0x146>, /* WIFI_W_WKUP_HOST */ 1289 <MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20 0x46>; /* WIFI_WKUP_WLAN */ 1290 }; 1291 1292 pinctrl_wifi_i2s: bti2sgrp { 1293 fsl,pins = 1294 <MX8MM_IOMUXC_SAI1_RXD4_SAI6_TX_BCLK 0x6>, /* WIFI_TX_BCLK */ 1295 <MX8MM_IOMUXC_SAI1_RXD5_SAI6_TX_DATA0 0x6>, /* WIFI_TX_DATA0 */ 1296 <MX8MM_IOMUXC_SAI1_RXD6_SAI6_TX_SYNC 0x6>, /* WIFI_TX_SYNC */ 1297 <MX8MM_IOMUXC_SAI1_TXD5_SAI6_RX_DATA0 0x6>; /* WIFI_RX_DATA0 */ 1298 }; 1299 1300 pinctrl_wifi_pwr_en: wifipwrengrp { 1301 fsl,pins = 1302 <MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25 0x6>; /* PMIC_EN_WIFI */ 1303 }; 1304}; 1305