1// SPDX-License-Identifier: GPL-2.0+ OR MIT
2/*
3 * Copyright 2021-2022 Marek Vasut <marex@denx.de>
4 */
5
6/dts-v1/;
7
8#include "imx8mm-verdin.dtsi"
9
10/ {
11	model = "MENLO MX8MM EMBEDDED DEVICE";
12	compatible = "menlo,mx8menlo",
13		     "toradex,verdin-imx8mm",
14		     "fsl,imx8mm";
15
16	/delete-node/ gpio-keys;
17
18	leds {
19		compatible = "gpio-leds";
20		pinctrl-names = "default";
21		pinctrl-0 = <&pinctrl_led>;
22
23		user1 {
24			label = "TestLed601";
25			gpios = <&gpio4 18 GPIO_ACTIVE_HIGH>;
26			linux,default-trigger = "mmc0";
27		};
28
29		user2 {
30			label = "TestLed602";
31			gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>;
32			linux,default-trigger = "heartbeat";
33		};
34	};
35
36	beeper {
37		compatible = "gpio-beeper";
38		pinctrl-names = "default";
39		pinctrl-0 = <&pinctrl_beeper>;
40		gpios = <&gpio5 3 GPIO_ACTIVE_HIGH>;
41	};
42
43	/* Fixed clock dedicated to SPI CAN on carrier board */
44	clk_xtal20: clk-xtal20 {
45		compatible = "fixed-clock";
46		#clock-cells = <0>;
47		clock-frequency = <20000000>;
48	};
49};
50
51&ecspi1 {
52	#address-cells = <1>;
53	#size-cells = <0>;
54	pinctrl-names = "default";
55	pinctrl-0 = <&pinctrl_ecspi1>;
56	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
57	status = "okay";
58
59	/* CAN controller on the baseboard */
60	canfd: can@0 {
61		compatible = "microchip,mcp2518fd";
62		clocks = <&clk_xtal20>;
63		interrupt-parent = <&gpio1>;
64		interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
65		reg = <0>;
66		spi-max-frequency = <2000000>;
67	};
68
69};
70
71&ecspi2 {
72	pinctrl-0 = <&pinctrl_ecspi2 &pinctrl_gpio1>;
73	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>, <&gpio3 4 GPIO_ACTIVE_LOW>;
74	status = "okay";
75
76	spidev@0 {
77		compatible = "menlo,m53cpld";
78		reg = <0>;
79		spi-max-frequency = <25000000>;
80	};
81
82	spidev@1 {
83		compatible = "menlo,m53cpld";
84		reg = <1>;
85		spi-max-frequency = <25000000>;
86	};
87
88};
89
90&ethphy0 {
91	max-speed = <100>;
92};
93
94&fec1 {
95	status = "okay";
96};
97
98&flexspi {
99	status = "okay";
100
101	flash@0 {
102		reg = <0>;
103		#address-cells = <1>;
104		#size-cells = <1>;
105		compatible = "jedec,spi-nor";
106		spi-max-frequency = <66000000>;
107		spi-rx-bus-width = <4>;
108		spi-tx-bus-width = <4>;
109	};
110};
111
112&gpio1 {
113	gpio-line-names =
114		"", "", "", "",
115		"", "", "", "",
116		"", "", "", "",
117		"", "", "", "",
118		"", "", "", "",
119		"", "", "", "",
120		"", "", "", "",
121		"", "", "", "";
122};
123
124&gpio2 {
125	gpio-line-names =
126		"", "", "", "",
127		"", "", "", "",
128		"", "", "", "",
129		"", "", "", "",
130		"", "", "", "",
131		"", "", "", "",
132		"", "", "", "",
133		"", "", "", "";
134};
135
136&gpio3 {
137	gpio-line-names =
138		"", "", "", "",
139		"", "", "", "",
140		"", "", "", "",
141		"", "", "", "",
142		"", "", "", "",
143		"", "", "DISP_reset", "KBD_intI",
144		"", "", "", "",
145		"", "", "", "";
146};
147
148&gpio4 {
149	/*
150	 * CPLD_D[n] is ARM_CPLD[n] in schematic
151	 * CPLD_int is SA_INTERRUPT in schematic
152	 * CPLD_reset is RESET_SOFT in schematic
153	 */
154	gpio-line-names =
155		"CPLD_D[1]", "CPLD_int", "CPLD_reset", "",
156		"", "CPLD_D[0]", "", "",
157		"", "", "", "CPLD_D[2]",
158		"CPLD_D[3]", "CPLD_D[4]", "CPLD_D[5]", "CPLD_D[6]",
159		"CPLD_D[7]", "", "", "",
160		"", "", "", "",
161		"", "", "", "KBD_intK",
162		"", "", "", "";
163};
164
165&gpio5 {
166	gpio-line-names =
167		"", "", "", "",
168		"", "", "", "",
169		"", "", "", "",
170		"", "", "", "",
171		"", "", "", "",
172		"", "", "", "",
173		"", "", "", "",
174		"", "", "", "";
175};
176
177&gpio_expander_21 {
178	status = "okay";
179};
180
181&hwmon {
182	status = "okay";
183};
184
185&i2c3 {
186	status = "okay";
187};
188
189&i2c4 {
190	/* None of this is present on the SoM. */
191	/delete-node/ bridge@2c;
192	/delete-node/ hdmi@48;
193	/delete-node/ touch@4a;
194	/delete-node/ sensor@4f;
195	/delete-node/ eeprom@50;
196	/delete-node/ eeprom@57;
197};
198
199&iomuxc {
200	pinctrl-0 = <&pinctrl_gpio7>, <&pinctrl_gpio_hog1>,
201		    <&pinctrl_gpio_hog2>, <&pinctrl_gpio_hog3>;
202
203	pinctrl_beeper: beepergrp {
204		fsl,pins = <
205			MX8MM_IOMUXC_SPDIF_TX_GPIO5_IO3			0x1c4
206		>;
207	};
208
209	pinctrl_ecspi1: ecspi1grp {
210		fsl,pins = <
211			MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK		0x4
212			MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI		0x4
213			MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO		0x1c4
214			MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x1c4
215		>;
216	};
217
218	pinctrl_led: ledgrp {
219		fsl,pins = <
220			MX8MM_IOMUXC_SAI1_TXD6_GPIO4_IO18		0x1c4
221			MX8MM_IOMUXC_SAI1_TXFS_GPIO4_IO10		0x1c4
222		>;
223	};
224
225	pinctrl_uart4_rts: uart4rtsgrp {
226		fsl,pins = <
227			/* SODIMM 222 */
228			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x184
229		>;
230	};
231};
232
233&pinctrl_gpio1 {
234	fsl,pins = <
235		/* SODIMM 206 */
236		MX8MM_IOMUXC_NAND_CE3_B_GPIO3_IO4			0x1c4
237	>;
238};
239
240&pinctrl_gpio_hog1 {
241	fsl,pins = <
242		/* SODIMM 88 */
243		MX8MM_IOMUXC_SAI1_MCLK_GPIO4_IO20			0x1c4
244		/* CPLD_int */
245		MX8MM_IOMUXC_SAI1_RXC_GPIO4_IO1				0x1c4
246		/* CPLD_reset */
247		MX8MM_IOMUXC_SAI1_RXD0_GPIO4_IO2			0x1c4
248		/* SODIMM 94 */
249		MX8MM_IOMUXC_SAI1_RXD1_GPIO4_IO3			0x1c4
250		/* SODIMM 96 */
251		MX8MM_IOMUXC_SAI1_RXD2_GPIO4_IO4			0x1c4
252		/* CPLD_D[7] */
253		MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5			0x1c4
254		/* CPLD_D[6] */
255		MX8MM_IOMUXC_SAI1_RXFS_GPIO4_IO0			0x1c4
256		/* CPLD_D[5] */
257		MX8MM_IOMUXC_SAI1_TXC_GPIO4_IO11			0x1c4
258		/* CPLD_D[4] */
259		MX8MM_IOMUXC_SAI1_TXD0_GPIO4_IO12			0x1c4
260		/* CPLD_D[3] */
261		MX8MM_IOMUXC_SAI1_TXD1_GPIO4_IO13			0x1c4
262		/* CPLD_D[2] */
263		MX8MM_IOMUXC_SAI1_TXD2_GPIO4_IO14			0x1c4
264		/* CPLD_D[1] */
265		MX8MM_IOMUXC_SAI1_TXD3_GPIO4_IO15			0x1c4
266		/* CPLD_D[0] */
267		MX8MM_IOMUXC_SAI1_TXD4_GPIO4_IO16			0x1c4
268		/* KBD_intK */
269		MX8MM_IOMUXC_SAI2_MCLK_GPIO4_IO27			0x1c4
270		/* DISP_reset */
271		MX8MM_IOMUXC_SAI5_RXD1_GPIO3_IO22			0x1c4
272		/* KBD_intI */
273		MX8MM_IOMUXC_SAI5_RXD2_GPIO3_IO23			0x1c4
274		/* SODIMM 46 */
275		MX8MM_IOMUXC_SAI5_RXD3_GPIO3_IO24			0x1c4
276	>;
277};
278
279&pinctrl_uart1 {
280	fsl,pins = <
281		/* SODIMM 149 */
282		MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX			0x1c4
283		/* SODIMM 147 */
284		MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX			0x1c4
285		/* SODIMM 210 */
286		MX8MM_IOMUXC_UART3_RXD_UART1_DTE_RTS_B			0x1c4
287		/* SODIMM 212 */
288		MX8MM_IOMUXC_UART3_TXD_UART1_DTE_CTS_B			0x1c4
289	>;
290};
291
292&reg_usb_otg1_vbus {
293	/delete-property/ enable-active-high;
294	gpio = <&gpio1 12 GPIO_ACTIVE_LOW>;
295};
296
297&reg_usb_otg2_vbus {
298	/delete-property/ enable-active-high;
299	gpio = <&gpio1 14 GPIO_ACTIVE_LOW>;
300};
301
302&sai2 {
303	status = "disabled";
304};
305
306&uart1 {
307	uart-has-rtscts;
308	status = "okay";
309};
310
311&uart2 {
312	status = "okay";
313};
314
315&uart4 {
316	pinctrl-0 = <&pinctrl_uart4 &pinctrl_uart4_rts>;
317	linux,rs485-enabled-at-boot-time;
318	rts-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
319	status = "okay";
320};
321
322&usbotg1 {
323	dr_mode = "peripheral";
324	status = "okay";
325};
326
327&usbotg2 {
328	dr_mode = "host";
329	status = "okay";
330};
331
332&usdhc2 {
333	status = "okay";
334};
335