1// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2/*
3 * Device Tree file for NXP LS1088A RDB Board.
4 *
5 * Copyright 2017 NXP
6 *
7 * Harninder Rai <harninder.rai@nxp.com>
8 *
9 */
10
11/dts-v1/;
12
13#include "fsl-ls1088a.dtsi"
14
15/ {
16	model = "LS1088A RDB Board";
17	compatible = "fsl,ls1088a-rdb", "fsl,ls1088a";
18};
19
20&i2c0 {
21	status = "okay";
22
23	i2c-switch@77 {
24		compatible = "nxp,pca9547";
25		reg = <0x77>;
26		#address-cells = <1>;
27		#size-cells = <0>;
28
29		i2c@2 {
30			#address-cells = <1>;
31			#size-cells = <0>;
32			reg = <0x2>;
33
34			ina220@40 {
35				compatible = "ti,ina220";
36				reg = <0x40>;
37				shunt-resistor = <1000>;
38			};
39		};
40
41		i2c@3 {
42			#address-cells = <1>;
43			#size-cells = <0>;
44			reg = <0x3>;
45
46			temp-sensor@4c {
47				compatible = "adi,adt7461a";
48				reg = <0x4c>;
49			};
50
51			rtc@51 {
52				compatible = "nxp,pcf2129";
53				reg = <0x51>;
54				/* IRQ10_B */
55				interrupts = <0 150 IRQ_TYPE_LEVEL_HIGH>;
56			};
57		};
58	};
59};
60
61&ifc {
62	ranges = <0 0 0x5 0x30000000 0x00010000
63		  2 0 0x5 0x20000000 0x00010000>;
64	status = "okay";
65
66	nand@0,0 {
67		compatible = "fsl,ifc-nand";
68		reg = <0x0 0x0 0x10000>;
69	};
70
71	fpga: board-control@2,0 {
72		compatible = "fsl,ls1088ardb-fpga", "fsl,fpga-qixis";
73		reg = <0x2 0x0 0x0000100>;
74	};
75};
76
77&duart0 {
78	status = "okay";
79};
80
81&duart1 {
82	status = "okay";
83};
84
85&esdhc {
86	mmc-hs200-1_8v;
87	status = "okay";
88};
89
90&qspi {
91	status = "okay";
92
93	s25fs512s0: flash@0 {
94		compatible = "jedec,spi-nor";
95		#address-cells = <1>;
96		#size-cells = <1>;
97		spi-max-frequency = <50000000>;
98		spi-rx-bus-width = <4>;
99		spi-tx-bus-width = <1>;
100		reg = <0>;
101	};
102
103	s25fs512s1: flash@1 {
104		compatible = "jedec,spi-nor";
105		#address-cells = <1>;
106		#size-cells = <1>;
107		spi-max-frequency = <50000000>;
108		spi-rx-bus-width = <4>;
109		spi-tx-bus-width = <1>;
110		reg = <1>;
111	};
112};
113
114&sata {
115	status = "okay";
116};
117
118&usb0 {
119	status = "okay";
120};
121
122&usb1 {
123	dr_mode = "otg";
124	status = "okay";
125};
126