1// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2/*
3 * Device Tree file for NXP LS1028A RDB Board.
4 *
5 * Copyright 2018 NXP
6 *
7 * Harninder Rai <harninder.rai@nxp.com>
8 *
9 */
10
11/dts-v1/;
12#include "fsl-ls1028a.dtsi"
13
14/ {
15	model = "LS1028A RDB Board";
16	compatible = "fsl,ls1028a-rdb", "fsl,ls1028a";
17
18	aliases {
19		crypto = &crypto;
20		serial0 = &duart0;
21		serial1 = &duart1;
22	};
23
24	chosen {
25		stdout-path = "serial0:115200n8";
26	};
27
28	memory@80000000 {
29		device_type = "memory";
30		reg = <0x0 0x80000000 0x1 0x0000000>;
31	};
32
33	sys_mclk: clock-mclk {
34		compatible = "fixed-clock";
35		#clock-cells = <0>;
36		clock-frequency = <25000000>;
37	};
38
39	reg_1p8v: regulator-1p8v {
40		compatible = "regulator-fixed";
41		regulator-name = "1P8V";
42		regulator-min-microvolt = <1800000>;
43		regulator-max-microvolt = <1800000>;
44		regulator-always-on;
45	};
46
47	sb_3v3: regulator-sb3v3 {
48		compatible = "regulator-fixed";
49		regulator-name = "3v3_vbus";
50		regulator-min-microvolt = <3300000>;
51		regulator-max-microvolt = <3300000>;
52		regulator-boot-on;
53		regulator-always-on;
54	};
55
56	sound {
57		compatible = "simple-audio-card";
58		simple-audio-card,format = "i2s";
59		simple-audio-card,widgets =
60			"Microphone", "Microphone Jack",
61			"Headphone", "Headphone Jack",
62			"Speaker", "Speaker Ext",
63			"Line", "Line In Jack";
64		simple-audio-card,routing =
65			"MIC_IN", "Microphone Jack",
66			"Microphone Jack", "Mic Bias",
67			"LINE_IN", "Line In Jack",
68			"Headphone Jack", "HP_OUT",
69			"Speaker Ext", "LINE_OUT";
70
71		simple-audio-card,cpu {
72			sound-dai = <&sai4>;
73			frame-master;
74			bitclock-master;
75		};
76
77		simple-audio-card,codec {
78			sound-dai = <&sgtl5000>;
79			frame-master;
80			bitclock-master;
81			system-clock-frequency = <25000000>;
82		};
83	};
84};
85
86&esdhc {
87	sd-uhs-sdr104;
88	sd-uhs-sdr50;
89	sd-uhs-sdr25;
90	sd-uhs-sdr12;
91	status = "okay";
92};
93
94&esdhc1 {
95	mmc-hs200-1_8v;
96	mmc-hs400-1_8v;
97	bus-width = <8>;
98	status = "okay";
99};
100
101&fspi {
102	status = "okay";
103
104	mt35xu02g0: flash@0 {
105		compatible = "jedec,spi-nor";
106		#address-cells = <1>;
107		#size-cells = <1>;
108		spi-max-frequency = <50000000>;
109		/* The following setting enables 1-1-8 (CMD-ADDR-DATA) mode */
110		spi-rx-bus-width = <8>; /* 8 SPI Rx lines */
111		spi-tx-bus-width = <1>; /* 1 SPI Tx line */
112		reg = <0>;
113	};
114};
115
116&i2c0 {
117	status = "okay";
118
119	i2c-mux@77 {
120		compatible = "nxp,pca9847";
121		reg = <0x77>;
122		#address-cells = <1>;
123		#size-cells = <0>;
124
125		i2c@1 {
126			#address-cells = <1>;
127			#size-cells = <0>;
128			reg = <0x1>;
129
130			sgtl5000: audio-codec@a {
131				#sound-dai-cells = <0>;
132				compatible = "fsl,sgtl5000";
133				reg = <0xa>;
134				VDDA-supply = <&reg_1p8v>;
135				VDDIO-supply = <&reg_1p8v>;
136				clocks = <&sys_mclk>;
137				sclk-strength = <3>;
138			};
139		};
140
141		i2c@2 {
142			#address-cells = <1>;
143			#size-cells = <0>;
144			reg = <0x02>;
145
146			current-monitor@40 {
147				compatible = "ti,ina220";
148				reg = <0x40>;
149				shunt-resistor = <500>;
150			};
151		};
152
153		i2c@3 {
154			#address-cells = <1>;
155			#size-cells = <0>;
156			reg = <0x3>;
157
158			temperature-sensor@4c {
159				compatible = "nxp,sa56004";
160				reg = <0x4c>;
161				vcc-supply = <&sb_3v3>;
162			};
163
164			rtc@51 {
165				compatible = "nxp,pcf2129";
166				reg = <0x51>;
167			};
168		};
169	};
170};
171
172&duart0 {
173	status = "okay";
174};
175
176&duart1 {
177	status = "okay";
178};
179
180&enetc_port0 {
181	phy-handle = <&sgmii_phy0>;
182	phy-connection-type = "sgmii";
183
184	mdio {
185		#address-cells = <1>;
186		#size-cells = <0>;
187		sgmii_phy0: ethernet-phy@2 {
188			reg = <0x2>;
189		};
190	};
191};
192
193&enetc_port1 {
194	status = "disabled";
195};
196
197&sai4 {
198	status = "okay";
199};
200
201&sata {
202	status = "okay";
203};
204
205&usb1 {
206	dr_mode = "otg";
207};
208