1// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2// Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.xyz>
3// Based on sun50i-h5-orangepi-pc2.dts, which is:
4//   Copyright (C) 2016 ARM Ltd.
5
6/dts-v1/;
7#include "sun50i-h5.dtsi"
8
9#include <dt-bindings/gpio/gpio.h>
10#include <dt-bindings/input/input.h>
11
12/ {
13	model = "Xunlong Orange Pi Prime";
14	compatible = "xunlong,orangepi-prime", "allwinner,sun50i-h5";
15
16	aliases {
17		ethernet0 = &emac;
18		serial0 = &uart0;
19	};
20
21	chosen {
22		stdout-path = "serial0:115200n8";
23	};
24
25	connector {
26		compatible = "hdmi-connector";
27		type = "a";
28
29		port {
30			hdmi_con_in: endpoint {
31				remote-endpoint = <&hdmi_out_con>;
32			};
33		};
34	};
35
36	leds {
37		compatible = "gpio-leds";
38
39		pwr {
40			label = "orangepi:green:pwr";
41			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
42			default-state = "on";
43		};
44
45		status {
46			label = "orangepi:red:status";
47			gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>;
48		};
49	};
50
51	r-gpio-keys {
52		compatible = "gpio-keys";
53
54		sw4 {
55			label = "sw4";
56			linux,code = <BTN_0>;
57			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
58		};
59	};
60
61	reg_gmac_3v3: gmac-3v3 {
62		compatible = "regulator-fixed";
63		regulator-name = "gmac-3v3";
64		regulator-min-microvolt = <3300000>;
65		regulator-max-microvolt = <3300000>;
66		startup-delay-us = <100000>;
67		enable-active-high;
68		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
69	};
70
71	reg_vcc3v3: vcc3v3 {
72		compatible = "regulator-fixed";
73		regulator-name = "vcc3v3";
74		regulator-min-microvolt = <3300000>;
75		regulator-max-microvolt = <3300000>;
76	};
77
78	reg_usb0_vbus: usb0-vbus {
79		compatible = "regulator-fixed";
80		regulator-name = "usb0-vbus";
81		regulator-min-microvolt = <5000000>;
82		regulator-max-microvolt = <5000000>;
83		enable-active-high;
84		gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
85		status = "okay";
86	};
87
88	wifi_pwrseq: wifi_pwrseq {
89		compatible = "mmc-pwrseq-simple";
90		reset-gpios = <&pio 2 14 GPIO_ACTIVE_LOW>; /* PC14 */
91	};
92};
93
94&codec {
95	allwinner,audio-routing =
96		"Line Out", "LINEOUT",
97		"MIC1", "Mic",
98		"Mic",  "MBIAS";
99	status = "okay";
100};
101
102&de {
103	status = "okay";
104};
105
106&ehci0 {
107	status = "okay";
108};
109
110&ehci1 {
111	status = "okay";
112};
113
114&ehci2 {
115	status = "okay";
116};
117
118&ehci3 {
119	status = "okay";
120};
121
122&emac {
123	pinctrl-names = "default";
124	pinctrl-0 = <&emac_rgmii_pins>;
125	phy-supply = <&reg_gmac_3v3>;
126	phy-handle = <&ext_rgmii_phy>;
127	phy-mode = "rgmii-id";
128	status = "okay";
129};
130
131&external_mdio {
132	ext_rgmii_phy: ethernet-phy@1 {
133		compatible = "ethernet-phy-ieee802.3-c22";
134		reg = <1>;
135	};
136};
137
138&hdmi {
139	status = "okay";
140};
141
142&hdmi_out {
143	hdmi_out_con: endpoint {
144		remote-endpoint = <&hdmi_con_in>;
145	};
146};
147
148&ir {
149	pinctrl-names = "default";
150	pinctrl-0 = <&r_ir_rx_pin>;
151	status = "okay";
152};
153
154&mmc0 {
155	vmmc-supply = <&reg_vcc3v3>;
156	bus-width = <4>;
157	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
158	status = "okay";
159};
160
161&mmc1 {
162	vmmc-supply = <&reg_vcc3v3>;
163	mmc-pwrseq = <&wifi_pwrseq>;
164	bus-width = <4>;
165	non-removable;
166	status = "okay";
167};
168
169&ohci0 {
170	status = "okay";
171};
172
173&ohci1 {
174	status = "okay";
175};
176
177&ohci2 {
178	status = "okay";
179};
180
181&ohci3 {
182	status = "okay";
183};
184
185&uart0 {
186	pinctrl-names = "default";
187	pinctrl-0 = <&uart0_pa_pins>;
188	status = "okay";
189};
190
191&uart1 {
192	pinctrl-names = "default";
193	pinctrl-0 = <&uart1_pins>;
194	status = "disabled";
195};
196
197&uart2 {
198	pinctrl-names = "default";
199	pinctrl-0 = <&uart2_pins>;
200	status = "disabled";
201};
202
203&usb_otg {
204	dr_mode = "otg";
205	status = "okay";
206};
207
208&usbphy {
209	/* USB Type-A ports' VBUS is always on */
210	usb0_id_det-gpios = <&pio 0 21 GPIO_ACTIVE_HIGH>; /* PA21 */
211	usb0_vbus-supply = <&reg_usb0_vbus>;
212	status = "okay";
213};
214