1 /* 2 * arch/arm/mach-spear3xx/spear3xx.c 3 * 4 * SPEAr3XX machines common source file 5 * 6 * Copyright (C) 2009-2012 ST Microelectronics 7 * Viresh Kumar <viresh.linux@gmail.com> 8 * 9 * This file is licensed under the terms of the GNU General Public 10 * License version 2. This program is licensed "as is" without any 11 * warranty of any kind, whether express or implied. 12 */ 13 14 #define pr_fmt(fmt) "SPEAr3xx: " fmt 15 16 #include <linux/amba/pl022.h> 17 #include <linux/amba/pl080.h> 18 #include <linux/clk.h> 19 #include <linux/io.h> 20 #include <asm/mach/map.h> 21 #include "pl080.h" 22 #include "generic.h" 23 #include <mach/spear.h> 24 #include <mach/misc_regs.h> 25 26 /* ssp device registration */ 27 struct pl022_ssp_controller pl022_plat_data = { 28 .bus_id = 0, 29 .enable_dma = 1, 30 .dma_filter = pl08x_filter_id, 31 .dma_tx_param = "ssp0_tx", 32 .dma_rx_param = "ssp0_rx", 33 /* 34 * This is number of spi devices that can be connected to spi. There are 35 * two type of chipselects on which slave devices can work. One is chip 36 * select provided by spi masters other is controlled through external 37 * gpio's. We can't use chipselect provided from spi master (because as 38 * soon as FIFO becomes empty, CS is disabled and transfer ends). So 39 * this number now depends on number of gpios available for spi. each 40 * slave on each master requires a separate gpio pin. 41 */ 42 .num_chipselect = 2, 43 }; 44 45 /* dmac device registration */ 46 struct pl08x_platform_data pl080_plat_data = { 47 .memcpy_channel = { 48 .bus_id = "memcpy", 49 .cctl_memcpy = 50 (PL080_BSIZE_16 << PL080_CONTROL_SB_SIZE_SHIFT | \ 51 PL080_BSIZE_16 << PL080_CONTROL_DB_SIZE_SHIFT | \ 52 PL080_WIDTH_32BIT << PL080_CONTROL_SWIDTH_SHIFT | \ 53 PL080_WIDTH_32BIT << PL080_CONTROL_DWIDTH_SHIFT | \ 54 PL080_CONTROL_PROT_BUFF | PL080_CONTROL_PROT_CACHE | \ 55 PL080_CONTROL_PROT_SYS), 56 }, 57 .lli_buses = PL08X_AHB1, 58 .mem_buses = PL08X_AHB1, 59 .get_xfer_signal = pl080_get_signal, 60 .put_xfer_signal = pl080_put_signal, 61 }; 62 63 /* 64 * Following will create 16MB static virtual/physical mappings 65 * PHYSICAL VIRTUAL 66 * 0xD0000000 0xFD000000 67 * 0xFC000000 0xFC000000 68 */ 69 struct map_desc spear3xx_io_desc[] __initdata = { 70 { 71 .virtual = (unsigned long)VA_SPEAR_ICM1_2_BASE, 72 .pfn = __phys_to_pfn(SPEAR_ICM1_2_BASE), 73 .length = SZ_16M, 74 .type = MT_DEVICE 75 }, { 76 .virtual = (unsigned long)VA_SPEAR_ICM3_SMI_CTRL_BASE, 77 .pfn = __phys_to_pfn(SPEAR_ICM3_SMI_CTRL_BASE), 78 .length = SZ_16M, 79 .type = MT_DEVICE 80 }, 81 }; 82 83 /* This will create static memory mapping for selected devices */ 84 void __init spear3xx_map_io(void) 85 { 86 iotable_init(spear3xx_io_desc, ARRAY_SIZE(spear3xx_io_desc)); 87 } 88 89 void __init spear3xx_timer_init(void) 90 { 91 char pclk_name[] = "pll3_clk"; 92 struct clk *gpt_clk, *pclk; 93 94 spear3xx_clk_init(MISC_BASE, VA_SPEAR320_SOC_CONFIG_BASE); 95 96 /* get the system timer clock */ 97 gpt_clk = clk_get_sys("gpt0", NULL); 98 if (IS_ERR(gpt_clk)) { 99 pr_err("%s:couldn't get clk for gpt\n", __func__); 100 BUG(); 101 } 102 103 /* get the suitable parent clock for timer*/ 104 pclk = clk_get(NULL, pclk_name); 105 if (IS_ERR(pclk)) { 106 pr_err("%s:couldn't get %s as parent for gpt\n", 107 __func__, pclk_name); 108 BUG(); 109 } 110 111 clk_set_parent(gpt_clk, pclk); 112 clk_put(gpt_clk); 113 clk_put(pclk); 114 115 spear_setup_of_timer(); 116 } 117