1 /* 2 * linux/arch/arm/mach-sa1100/assabet.c 3 * 4 * Author: Nicolas Pitre 5 * 6 * This file contains all Assabet-specific tweaks. 7 * 8 * This program is free software; you can redistribute it and/or modify 9 * it under the terms of the GNU General Public License version 2 as 10 * published by the Free Software Foundation. 11 */ 12 #include <linux/init.h> 13 #include <linux/kernel.h> 14 #include <linux/module.h> 15 #include <linux/errno.h> 16 #include <linux/ioport.h> 17 #include <linux/platform_data/sa11x0-serial.h> 18 #include <linux/serial_core.h> 19 #include <linux/platform_device.h> 20 #include <linux/mfd/ucb1x00.h> 21 #include <linux/mtd/mtd.h> 22 #include <linux/mtd/partitions.h> 23 #include <linux/delay.h> 24 #include <linux/mm.h> 25 #include <linux/leds.h> 26 #include <linux/slab.h> 27 28 #include <video/sa1100fb.h> 29 30 #include <mach/hardware.h> 31 #include <asm/mach-types.h> 32 #include <asm/setup.h> 33 #include <asm/page.h> 34 #include <asm/pgtable-hwdef.h> 35 #include <asm/pgtable.h> 36 #include <asm/tlbflush.h> 37 38 #include <asm/mach/arch.h> 39 #include <asm/mach/flash.h> 40 #include <asm/mach/irda.h> 41 #include <asm/mach/map.h> 42 #include <mach/assabet.h> 43 #include <linux/platform_data/mfd-mcp-sa11x0.h> 44 #include <mach/irqs.h> 45 46 #include "generic.h" 47 48 #define ASSABET_BCR_DB1110 \ 49 (ASSABET_BCR_SPK_OFF | \ 50 ASSABET_BCR_LED_GREEN | ASSABET_BCR_LED_RED | \ 51 ASSABET_BCR_RS232EN | ASSABET_BCR_LCD_12RGB | \ 52 ASSABET_BCR_IRDA_MD0) 53 54 #define ASSABET_BCR_DB1111 \ 55 (ASSABET_BCR_SPK_OFF | \ 56 ASSABET_BCR_LED_GREEN | ASSABET_BCR_LED_RED | \ 57 ASSABET_BCR_RS232EN | ASSABET_BCR_LCD_12RGB | \ 58 ASSABET_BCR_CF_BUS_OFF | ASSABET_BCR_STEREO_LB | \ 59 ASSABET_BCR_IRDA_MD0 | ASSABET_BCR_CF_RST) 60 61 unsigned long SCR_value = ASSABET_SCR_INIT; 62 EXPORT_SYMBOL(SCR_value); 63 64 static unsigned long BCR_value = ASSABET_BCR_DB1110; 65 66 void ASSABET_BCR_frob(unsigned int mask, unsigned int val) 67 { 68 unsigned long flags; 69 70 local_irq_save(flags); 71 BCR_value = (BCR_value & ~mask) | val; 72 ASSABET_BCR = BCR_value; 73 local_irq_restore(flags); 74 } 75 76 EXPORT_SYMBOL(ASSABET_BCR_frob); 77 78 /* 79 * The codec reset goes to three devices, so we need to release 80 * the rest when any one of these requests it. However, that 81 * causes the ADV7171 to consume around 100mA - more than half 82 * the LCD-blanked power. 83 * 84 * With the ADV7171, LCD and backlight enabled, we go over 85 * budget on the MAX846 Li-Ion charger, and if no Li-Ion battery 86 * is connected, the Assabet crashes. 87 */ 88 #define RST_UCB1X00 (1 << 0) 89 #define RST_UDA1341 (1 << 1) 90 #define RST_ADV7171 (1 << 2) 91 92 #define SDA GPIO_GPIO(15) 93 #define SCK GPIO_GPIO(18) 94 #define MOD GPIO_GPIO(17) 95 96 static void adv7171_start(void) 97 { 98 GPSR = SCK; 99 udelay(1); 100 GPSR = SDA; 101 udelay(2); 102 GPCR = SDA; 103 } 104 105 static void adv7171_stop(void) 106 { 107 GPSR = SCK; 108 udelay(2); 109 GPSR = SDA; 110 udelay(1); 111 } 112 113 static void adv7171_send(unsigned byte) 114 { 115 unsigned i; 116 117 for (i = 0; i < 8; i++, byte <<= 1) { 118 GPCR = SCK; 119 udelay(1); 120 if (byte & 0x80) 121 GPSR = SDA; 122 else 123 GPCR = SDA; 124 udelay(1); 125 GPSR = SCK; 126 udelay(1); 127 } 128 GPCR = SCK; 129 udelay(1); 130 GPSR = SDA; 131 udelay(1); 132 GPDR &= ~SDA; 133 GPSR = SCK; 134 udelay(1); 135 if (GPLR & SDA) 136 printk(KERN_WARNING "No ACK from ADV7171\n"); 137 udelay(1); 138 GPCR = SCK | SDA; 139 udelay(1); 140 GPDR |= SDA; 141 udelay(1); 142 } 143 144 static void adv7171_write(unsigned reg, unsigned val) 145 { 146 unsigned gpdr = GPDR; 147 unsigned gplr = GPLR; 148 149 ASSABET_BCR = BCR_value | ASSABET_BCR_AUDIO_ON; 150 udelay(100); 151 152 GPCR = SDA | SCK | MOD; /* clear L3 mode to ensure UDA1341 doesn't respond */ 153 GPDR = (GPDR | SCK | MOD) & ~SDA; 154 udelay(10); 155 if (!(GPLR & SDA)) 156 printk(KERN_WARNING "Something dragging SDA down?\n"); 157 GPDR |= SDA; 158 159 adv7171_start(); 160 adv7171_send(0x54); 161 adv7171_send(reg); 162 adv7171_send(val); 163 adv7171_stop(); 164 165 /* Restore GPIO state for L3 bus */ 166 GPSR = gplr & (SDA | SCK | MOD); 167 GPCR = (~gplr) & (SDA | SCK | MOD); 168 GPDR = gpdr; 169 } 170 171 static void adv7171_sleep(void) 172 { 173 /* Put the ADV7171 into sleep mode */ 174 adv7171_write(0x04, 0x40); 175 } 176 177 static unsigned codec_nreset; 178 179 static void assabet_codec_reset(unsigned mask, int set) 180 { 181 unsigned long flags; 182 bool old; 183 184 local_irq_save(flags); 185 old = !codec_nreset; 186 if (set) 187 codec_nreset &= ~mask; 188 else 189 codec_nreset |= mask; 190 191 if (old != !codec_nreset) { 192 if (codec_nreset) { 193 ASSABET_BCR_set(ASSABET_BCR_NCODEC_RST); 194 adv7171_sleep(); 195 } else { 196 ASSABET_BCR_clear(ASSABET_BCR_NCODEC_RST); 197 } 198 } 199 local_irq_restore(flags); 200 } 201 202 static void assabet_ucb1x00_reset(enum ucb1x00_reset state) 203 { 204 int set = state == UCB_RST_REMOVE || state == UCB_RST_SUSPEND || 205 state == UCB_RST_PROBE_FAIL; 206 assabet_codec_reset(RST_UCB1X00, set); 207 } 208 209 void assabet_uda1341_reset(int set) 210 { 211 assabet_codec_reset(RST_UDA1341, set); 212 } 213 EXPORT_SYMBOL(assabet_uda1341_reset); 214 215 216 /* 217 * Assabet flash support code. 218 */ 219 220 #ifdef ASSABET_REV_4 221 /* 222 * Phase 4 Assabet has two 28F160B3 flash parts in bank 0: 223 */ 224 static struct mtd_partition assabet_partitions[] = { 225 { 226 .name = "bootloader", 227 .size = 0x00020000, 228 .offset = 0, 229 .mask_flags = MTD_WRITEABLE, 230 }, { 231 .name = "bootloader params", 232 .size = 0x00020000, 233 .offset = MTDPART_OFS_APPEND, 234 .mask_flags = MTD_WRITEABLE, 235 }, { 236 .name = "jffs", 237 .size = MTDPART_SIZ_FULL, 238 .offset = MTDPART_OFS_APPEND, 239 } 240 }; 241 #else 242 /* 243 * Phase 5 Assabet has two 28F128J3A flash parts in bank 0: 244 */ 245 static struct mtd_partition assabet_partitions[] = { 246 { 247 .name = "bootloader", 248 .size = 0x00040000, 249 .offset = 0, 250 .mask_flags = MTD_WRITEABLE, 251 }, { 252 .name = "bootloader params", 253 .size = 0x00040000, 254 .offset = MTDPART_OFS_APPEND, 255 .mask_flags = MTD_WRITEABLE, 256 }, { 257 .name = "jffs", 258 .size = MTDPART_SIZ_FULL, 259 .offset = MTDPART_OFS_APPEND, 260 } 261 }; 262 #endif 263 264 static struct flash_platform_data assabet_flash_data = { 265 .map_name = "cfi_probe", 266 .parts = assabet_partitions, 267 .nr_parts = ARRAY_SIZE(assabet_partitions), 268 }; 269 270 static struct resource assabet_flash_resources[] = { 271 DEFINE_RES_MEM(SA1100_CS0_PHYS, SZ_32M), 272 DEFINE_RES_MEM(SA1100_CS1_PHYS, SZ_32M), 273 }; 274 275 276 /* 277 * Assabet IrDA support code. 278 */ 279 280 static int assabet_irda_set_power(struct device *dev, unsigned int state) 281 { 282 static unsigned int bcr_state[4] = { 283 ASSABET_BCR_IRDA_MD0, 284 ASSABET_BCR_IRDA_MD1|ASSABET_BCR_IRDA_MD0, 285 ASSABET_BCR_IRDA_MD1, 286 0 287 }; 288 289 if (state < 4) { 290 state = bcr_state[state]; 291 ASSABET_BCR_clear(state ^ (ASSABET_BCR_IRDA_MD1| 292 ASSABET_BCR_IRDA_MD0)); 293 ASSABET_BCR_set(state); 294 } 295 return 0; 296 } 297 298 static void assabet_irda_set_speed(struct device *dev, unsigned int speed) 299 { 300 if (speed < 4000000) 301 ASSABET_BCR_clear(ASSABET_BCR_IRDA_FSEL); 302 else 303 ASSABET_BCR_set(ASSABET_BCR_IRDA_FSEL); 304 } 305 306 static struct irda_platform_data assabet_irda_data = { 307 .set_power = assabet_irda_set_power, 308 .set_speed = assabet_irda_set_speed, 309 }; 310 311 static struct ucb1x00_plat_data assabet_ucb1x00_data = { 312 .reset = assabet_ucb1x00_reset, 313 .gpio_base = -1, 314 }; 315 316 static struct mcp_plat_data assabet_mcp_data = { 317 .mccr0 = MCCR0_ADM, 318 .sclk_rate = 11981000, 319 .codec_pdata = &assabet_ucb1x00_data, 320 }; 321 322 static void assabet_lcd_set_visual(u32 visual) 323 { 324 u_int is_true_color = visual == FB_VISUAL_TRUECOLOR; 325 326 if (machine_is_assabet()) { 327 #if 1 // phase 4 or newer Assabet's 328 if (is_true_color) 329 ASSABET_BCR_set(ASSABET_BCR_LCD_12RGB); 330 else 331 ASSABET_BCR_clear(ASSABET_BCR_LCD_12RGB); 332 #else 333 // older Assabet's 334 if (is_true_color) 335 ASSABET_BCR_clear(ASSABET_BCR_LCD_12RGB); 336 else 337 ASSABET_BCR_set(ASSABET_BCR_LCD_12RGB); 338 #endif 339 } 340 } 341 342 #ifndef ASSABET_PAL_VIDEO 343 static void assabet_lcd_backlight_power(int on) 344 { 345 if (on) 346 ASSABET_BCR_set(ASSABET_BCR_LIGHT_ON); 347 else 348 ASSABET_BCR_clear(ASSABET_BCR_LIGHT_ON); 349 } 350 351 /* 352 * Turn on/off the backlight. When turning the backlight on, we wait 353 * 500us after turning it on so we don't cause the supplies to droop 354 * when we enable the LCD controller (and cause a hard reset.) 355 */ 356 static void assabet_lcd_power(int on) 357 { 358 if (on) { 359 ASSABET_BCR_set(ASSABET_BCR_LCD_ON); 360 udelay(500); 361 } else 362 ASSABET_BCR_clear(ASSABET_BCR_LCD_ON); 363 } 364 365 /* 366 * The assabet uses a sharp LQ039Q2DS54 LCD module. It is actually 367 * takes an RGB666 signal, but we provide it with an RGB565 signal 368 * instead (def_rgb_16). 369 */ 370 static struct sa1100fb_mach_info lq039q2ds54_info = { 371 .pixclock = 171521, .bpp = 16, 372 .xres = 320, .yres = 240, 373 374 .hsync_len = 5, .vsync_len = 1, 375 .left_margin = 61, .upper_margin = 3, 376 .right_margin = 9, .lower_margin = 0, 377 378 .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT, 379 380 .lccr0 = LCCR0_Color | LCCR0_Sngl | LCCR0_Act, 381 .lccr3 = LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(2), 382 383 .backlight_power = assabet_lcd_backlight_power, 384 .lcd_power = assabet_lcd_power, 385 .set_visual = assabet_lcd_set_visual, 386 }; 387 #else 388 static void assabet_pal_backlight_power(int on) 389 { 390 ASSABET_BCR_clear(ASSABET_BCR_LIGHT_ON); 391 } 392 393 static void assabet_pal_power(int on) 394 { 395 ASSABET_BCR_clear(ASSABET_BCR_LCD_ON); 396 } 397 398 static struct sa1100fb_mach_info pal_info = { 399 .pixclock = 67797, .bpp = 16, 400 .xres = 640, .yres = 512, 401 402 .hsync_len = 64, .vsync_len = 6, 403 .left_margin = 125, .upper_margin = 70, 404 .right_margin = 115, .lower_margin = 36, 405 406 .lccr0 = LCCR0_Color | LCCR0_Sngl | LCCR0_Act, 407 .lccr3 = LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(512), 408 409 .backlight_power = assabet_pal_backlight_power, 410 .lcd_power = assabet_pal_power, 411 .set_visual = assabet_lcd_set_visual, 412 }; 413 #endif 414 415 #ifdef CONFIG_ASSABET_NEPONSET 416 static struct resource neponset_resources[] = { 417 DEFINE_RES_MEM(0x10000000, 0x08000000), 418 DEFINE_RES_MEM(0x18000000, 0x04000000), 419 DEFINE_RES_MEM(0x40000000, SZ_8K), 420 DEFINE_RES_IRQ(IRQ_GPIO25), 421 }; 422 #endif 423 424 static void __init assabet_init(void) 425 { 426 /* 427 * Ensure that the power supply is in "high power" mode. 428 */ 429 GPSR = GPIO_GPIO16; 430 GPDR |= GPIO_GPIO16; 431 432 /* 433 * Ensure that these pins are set as outputs and are driving 434 * logic 0. This ensures that we won't inadvertently toggle 435 * the WS latch in the CPLD, and we don't float causing 436 * excessive power drain. --rmk 437 */ 438 GPCR = GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM; 439 GPDR |= GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM; 440 441 /* 442 * Also set GPIO27 as an output; this is used to clock UART3 443 * via the FPGA and as otherwise has no pullups or pulldowns, 444 * so stop it floating. 445 */ 446 GPCR = GPIO_GPIO27; 447 GPDR |= GPIO_GPIO27; 448 449 /* 450 * Set up registers for sleep mode. 451 */ 452 PWER = PWER_GPIO0; 453 PGSR = 0; 454 PCFR = 0; 455 PSDR = 0; 456 PPDR |= PPC_TXD3 | PPC_TXD1; 457 PPSR |= PPC_TXD3 | PPC_TXD1; 458 459 sa11x0_ppc_configure_mcp(); 460 461 if (machine_has_neponset()) { 462 /* 463 * Angel sets this, but other bootloaders may not. 464 * 465 * This must precede any driver calls to BCR_set() 466 * or BCR_clear(). 467 */ 468 ASSABET_BCR = BCR_value = ASSABET_BCR_DB1111; 469 470 #ifndef CONFIG_ASSABET_NEPONSET 471 printk( "Warning: Neponset detected but full support " 472 "hasn't been configured in the kernel\n" ); 473 #else 474 platform_device_register_simple("neponset", 0, 475 neponset_resources, ARRAY_SIZE(neponset_resources)); 476 #endif 477 } 478 479 #ifndef ASSABET_PAL_VIDEO 480 sa11x0_register_lcd(&lq039q2ds54_info); 481 #else 482 sa11x0_register_lcd(&pal_video); 483 #endif 484 sa11x0_register_mtd(&assabet_flash_data, assabet_flash_resources, 485 ARRAY_SIZE(assabet_flash_resources)); 486 sa11x0_register_irda(&assabet_irda_data); 487 sa11x0_register_mcp(&assabet_mcp_data); 488 } 489 490 /* 491 * On Assabet, we must probe for the Neponset board _before_ 492 * paging_init() has occurred to actually determine the amount 493 * of RAM available. To do so, we map the appropriate IO section 494 * in the page table here in order to access GPIO registers. 495 */ 496 static void __init map_sa1100_gpio_regs( void ) 497 { 498 unsigned long phys = __PREG(GPLR) & PMD_MASK; 499 unsigned long virt = (unsigned long)io_p2v(phys); 500 int prot = PMD_TYPE_SECT | PMD_SECT_AP_WRITE | PMD_DOMAIN(DOMAIN_IO); 501 pmd_t *pmd; 502 503 pmd = pmd_offset(pud_offset(pgd_offset_k(virt), virt), virt); 504 *pmd = __pmd(phys | prot); 505 flush_pmd_entry(pmd); 506 } 507 508 /* 509 * Read System Configuration "Register" 510 * (taken from "Intel StrongARM SA-1110 Microprocessor Development Board 511 * User's Guide", section 4.4.1) 512 * 513 * This same scan is performed in arch/arm/boot/compressed/head-sa1100.S 514 * to set up the serial port for decompression status messages. We 515 * repeat it here because the kernel may not be loaded as a zImage, and 516 * also because it's a hassle to communicate the SCR value to the kernel 517 * from the decompressor. 518 * 519 * Note that IRQs are guaranteed to be disabled. 520 */ 521 static void __init get_assabet_scr(void) 522 { 523 unsigned long uninitialized_var(scr), i; 524 525 GPDR |= 0x3fc; /* Configure GPIO 9:2 as outputs */ 526 GPSR = 0x3fc; /* Write 0xFF to GPIO 9:2 */ 527 GPDR &= ~(0x3fc); /* Configure GPIO 9:2 as inputs */ 528 for(i = 100; i--; ) /* Read GPIO 9:2 */ 529 scr = GPLR; 530 GPDR |= 0x3fc; /* restore correct pin direction */ 531 scr &= 0x3fc; /* save as system configuration byte. */ 532 SCR_value = scr; 533 } 534 535 static void __init 536 fixup_assabet(struct tag *tags, char **cmdline, struct meminfo *mi) 537 { 538 /* This must be done before any call to machine_has_neponset() */ 539 map_sa1100_gpio_regs(); 540 get_assabet_scr(); 541 542 if (machine_has_neponset()) 543 printk("Neponset expansion board detected\n"); 544 } 545 546 547 static void assabet_uart_pm(struct uart_port *port, u_int state, u_int oldstate) 548 { 549 if (port->mapbase == _Ser1UTCR0) { 550 if (state) 551 ASSABET_BCR_clear(ASSABET_BCR_RS232EN | 552 ASSABET_BCR_COM_RTS | 553 ASSABET_BCR_COM_DTR); 554 else 555 ASSABET_BCR_set(ASSABET_BCR_RS232EN | 556 ASSABET_BCR_COM_RTS | 557 ASSABET_BCR_COM_DTR); 558 } 559 } 560 561 /* 562 * Assabet uses COM_RTS and COM_DTR for both UART1 (com port) 563 * and UART3 (radio module). We only handle them for UART1 here. 564 */ 565 static void assabet_set_mctrl(struct uart_port *port, u_int mctrl) 566 { 567 if (port->mapbase == _Ser1UTCR0) { 568 u_int set = 0, clear = 0; 569 570 if (mctrl & TIOCM_RTS) 571 clear |= ASSABET_BCR_COM_RTS; 572 else 573 set |= ASSABET_BCR_COM_RTS; 574 575 if (mctrl & TIOCM_DTR) 576 clear |= ASSABET_BCR_COM_DTR; 577 else 578 set |= ASSABET_BCR_COM_DTR; 579 580 ASSABET_BCR_clear(clear); 581 ASSABET_BCR_set(set); 582 } 583 } 584 585 static u_int assabet_get_mctrl(struct uart_port *port) 586 { 587 u_int ret = 0; 588 u_int bsr = ASSABET_BSR; 589 590 /* need 2 reads to read current value */ 591 bsr = ASSABET_BSR; 592 593 if (port->mapbase == _Ser1UTCR0) { 594 if (bsr & ASSABET_BSR_COM_DCD) 595 ret |= TIOCM_CD; 596 if (bsr & ASSABET_BSR_COM_CTS) 597 ret |= TIOCM_CTS; 598 if (bsr & ASSABET_BSR_COM_DSR) 599 ret |= TIOCM_DSR; 600 } else if (port->mapbase == _Ser3UTCR0) { 601 if (bsr & ASSABET_BSR_RAD_DCD) 602 ret |= TIOCM_CD; 603 if (bsr & ASSABET_BSR_RAD_CTS) 604 ret |= TIOCM_CTS; 605 if (bsr & ASSABET_BSR_RAD_DSR) 606 ret |= TIOCM_DSR; 607 if (bsr & ASSABET_BSR_RAD_RI) 608 ret |= TIOCM_RI; 609 } else { 610 ret = TIOCM_CD | TIOCM_CTS | TIOCM_DSR; 611 } 612 613 return ret; 614 } 615 616 static struct sa1100_port_fns assabet_port_fns __initdata = { 617 .set_mctrl = assabet_set_mctrl, 618 .get_mctrl = assabet_get_mctrl, 619 .pm = assabet_uart_pm, 620 }; 621 622 static struct map_desc assabet_io_desc[] __initdata = { 623 { /* Board Control Register */ 624 .virtual = 0xf1000000, 625 .pfn = __phys_to_pfn(0x12000000), 626 .length = 0x00100000, 627 .type = MT_DEVICE 628 }, { /* MQ200 */ 629 .virtual = 0xf2800000, 630 .pfn = __phys_to_pfn(0x4b800000), 631 .length = 0x00800000, 632 .type = MT_DEVICE 633 } 634 }; 635 636 static void __init assabet_map_io(void) 637 { 638 sa1100_map_io(); 639 iotable_init(assabet_io_desc, ARRAY_SIZE(assabet_io_desc)); 640 641 /* 642 * Set SUS bit in SDCR0 so serial port 1 functions. 643 * Its called GPCLKR0 in my SA1110 manual. 644 */ 645 Ser1SDCR0 |= SDCR0_SUS; 646 MSC1 = (MSC1 & ~0xffff) | 647 MSC_NonBrst | MSC_32BitStMem | 648 MSC_RdAcc(2) | MSC_WrAcc(2) | MSC_Rec(0); 649 650 if (!machine_has_neponset()) 651 sa1100_register_uart_fns(&assabet_port_fns); 652 653 /* 654 * When Neponset is attached, the first UART should be 655 * UART3. That's what Angel is doing and many documents 656 * are stating this. 657 * 658 * We do the Neponset mapping even if Neponset support 659 * isn't compiled in so the user will still get something on 660 * the expected physical serial port. 661 * 662 * We no longer do this; not all boot loaders support it, 663 * and UART3 appears to be somewhat unreliable with blob. 664 */ 665 sa1100_register_uart(0, 1); 666 sa1100_register_uart(2, 3); 667 } 668 669 /* LEDs */ 670 #if defined(CONFIG_NEW_LEDS) && defined(CONFIG_LEDS_CLASS) 671 struct assabet_led { 672 struct led_classdev cdev; 673 u32 mask; 674 }; 675 676 /* 677 * The triggers lines up below will only be used if the 678 * LED triggers are compiled in. 679 */ 680 static const struct { 681 const char *name; 682 const char *trigger; 683 } assabet_leds[] = { 684 { "assabet:red", "cpu0",}, 685 { "assabet:green", "heartbeat", }, 686 }; 687 688 /* 689 * The LED control in Assabet is reversed: 690 * - setting bit means turn off LED 691 * - clearing bit means turn on LED 692 */ 693 static void assabet_led_set(struct led_classdev *cdev, 694 enum led_brightness b) 695 { 696 struct assabet_led *led = container_of(cdev, 697 struct assabet_led, cdev); 698 699 if (b != LED_OFF) 700 ASSABET_BCR_clear(led->mask); 701 else 702 ASSABET_BCR_set(led->mask); 703 } 704 705 static enum led_brightness assabet_led_get(struct led_classdev *cdev) 706 { 707 struct assabet_led *led = container_of(cdev, 708 struct assabet_led, cdev); 709 710 return (ASSABET_BCR & led->mask) ? LED_OFF : LED_FULL; 711 } 712 713 static int __init assabet_leds_init(void) 714 { 715 int i; 716 717 if (!machine_is_assabet()) 718 return -ENODEV; 719 720 for (i = 0; i < ARRAY_SIZE(assabet_leds); i++) { 721 struct assabet_led *led; 722 723 led = kzalloc(sizeof(*led), GFP_KERNEL); 724 if (!led) 725 break; 726 727 led->cdev.name = assabet_leds[i].name; 728 led->cdev.brightness_set = assabet_led_set; 729 led->cdev.brightness_get = assabet_led_get; 730 led->cdev.default_trigger = assabet_leds[i].trigger; 731 732 if (!i) 733 led->mask = ASSABET_BCR_LED_RED; 734 else 735 led->mask = ASSABET_BCR_LED_GREEN; 736 737 if (led_classdev_register(NULL, &led->cdev) < 0) { 738 kfree(led); 739 break; 740 } 741 } 742 743 return 0; 744 } 745 746 /* 747 * Since we may have triggers on any subsystem, defer registration 748 * until after subsystem_init. 749 */ 750 fs_initcall(assabet_leds_init); 751 #endif 752 753 MACHINE_START(ASSABET, "Intel-Assabet") 754 .atag_offset = 0x100, 755 .fixup = fixup_assabet, 756 .map_io = assabet_map_io, 757 .nr_irqs = SA1100_NR_IRQS, 758 .init_irq = sa1100_init_irq, 759 .init_time = sa1100_timer_init, 760 .init_machine = assabet_init, 761 .init_late = sa11x0_init_late, 762 #ifdef CONFIG_SA1111 763 .dma_zone_size = SZ_1M, 764 #endif 765 .restart = sa11x0_restart, 766 MACHINE_END 767