1 /* 2 * Support for Sharp SL-Cxx00 Series of PDAs 3 * Models: SL-C3000 (Spitz), SL-C1000 (Akita) and SL-C3100 (Borzoi) 4 * 5 * Copyright (c) 2005 Richard Purdie 6 * 7 * Based on Sharp's 2.4 kernel patches/lubbock.c 8 * 9 * This program is free software; you can redistribute it and/or modify 10 * it under the terms of the GNU General Public License version 2 as 11 * published by the Free Software Foundation. 12 * 13 */ 14 15 #include <linux/kernel.h> 16 #include <linux/platform_device.h> 17 #include <linux/delay.h> 18 #include <linux/gpio_keys.h> 19 #include <linux/gpio.h> 20 #include <linux/leds.h> 21 #include <linux/i2c.h> 22 #include <linux/i2c/pxa-i2c.h> 23 #include <linux/platform_data/pca953x.h> 24 #include <linux/spi/spi.h> 25 #include <linux/spi/ads7846.h> 26 #include <linux/spi/corgi_lcd.h> 27 #include <linux/spi/pxa2xx_spi.h> 28 #include <linux/mtd/sharpsl.h> 29 #include <linux/mtd/physmap.h> 30 #include <linux/input/matrix_keypad.h> 31 #include <linux/regulator/machine.h> 32 #include <linux/io.h> 33 #include <linux/module.h> 34 #include <linux/reboot.h> 35 36 #include <asm/setup.h> 37 #include <asm/mach-types.h> 38 #include <asm/mach/arch.h> 39 #include <asm/mach/sharpsl_param.h> 40 #include <asm/hardware/scoop.h> 41 42 #include <mach/pxa27x.h> 43 #include <mach/pxa27x-udc.h> 44 #include <mach/reset.h> 45 #include <linux/platform_data/irda-pxaficp.h> 46 #include <linux/platform_data/mmc-pxamci.h> 47 #include <linux/platform_data/usb-ohci-pxa27x.h> 48 #include <linux/platform_data/video-pxafb.h> 49 #include <mach/spitz.h> 50 #include <mach/sharpsl_pm.h> 51 #include <mach/smemc.h> 52 53 #include "generic.h" 54 #include "devices.h" 55 56 /****************************************************************************** 57 * Pin configuration 58 ******************************************************************************/ 59 static unsigned long spitz_pin_config[] __initdata = { 60 /* Chip Selects */ 61 GPIO78_nCS_2, /* SCOOP #2 */ 62 GPIO79_nCS_3, /* NAND */ 63 GPIO80_nCS_4, /* SCOOP #1 */ 64 65 /* LCD - 16bpp Active TFT */ 66 GPIOxx_LCD_TFT_16BPP, 67 68 /* PC Card */ 69 GPIO48_nPOE, 70 GPIO49_nPWE, 71 GPIO50_nPIOR, 72 GPIO51_nPIOW, 73 GPIO85_nPCE_1, 74 GPIO54_nPCE_2, 75 GPIO55_nPREG, 76 GPIO56_nPWAIT, 77 GPIO57_nIOIS16, 78 GPIO104_PSKTSEL, 79 80 /* I2S */ 81 GPIO28_I2S_BITCLK_OUT, 82 GPIO29_I2S_SDATA_IN, 83 GPIO30_I2S_SDATA_OUT, 84 GPIO31_I2S_SYNC, 85 86 /* MMC */ 87 GPIO32_MMC_CLK, 88 GPIO112_MMC_CMD, 89 GPIO92_MMC_DAT_0, 90 GPIO109_MMC_DAT_1, 91 GPIO110_MMC_DAT_2, 92 GPIO111_MMC_DAT_3, 93 94 /* GPIOs */ 95 GPIO9_GPIO, /* SPITZ_GPIO_nSD_DETECT */ 96 GPIO16_GPIO, /* SPITZ_GPIO_SYNC */ 97 GPIO81_GPIO, /* SPITZ_GPIO_nSD_WP */ 98 GPIO41_GPIO, /* SPITZ_GPIO_USB_CONNECT */ 99 GPIO37_GPIO, /* SPITZ_GPIO_USB_HOST */ 100 GPIO35_GPIO, /* SPITZ_GPIO_USB_DEVICE */ 101 GPIO22_GPIO, /* SPITZ_GPIO_HSYNC */ 102 GPIO94_GPIO, /* SPITZ_GPIO_CF_CD */ 103 GPIO105_GPIO, /* SPITZ_GPIO_CF_IRQ */ 104 GPIO106_GPIO, /* SPITZ_GPIO_CF2_IRQ */ 105 106 /* GPIO matrix keypad */ 107 GPIO88_GPIO, /* column 0 */ 108 GPIO23_GPIO, /* column 1 */ 109 GPIO24_GPIO, /* column 2 */ 110 GPIO25_GPIO, /* column 3 */ 111 GPIO26_GPIO, /* column 4 */ 112 GPIO27_GPIO, /* column 5 */ 113 GPIO52_GPIO, /* column 6 */ 114 GPIO103_GPIO, /* column 7 */ 115 GPIO107_GPIO, /* column 8 */ 116 GPIO108_GPIO, /* column 9 */ 117 GPIO114_GPIO, /* column 10 */ 118 GPIO12_GPIO, /* row 0 */ 119 GPIO17_GPIO, /* row 1 */ 120 GPIO91_GPIO, /* row 2 */ 121 GPIO34_GPIO, /* row 3 */ 122 GPIO36_GPIO, /* row 4 */ 123 GPIO38_GPIO, /* row 5 */ 124 GPIO39_GPIO, /* row 6 */ 125 126 /* I2C */ 127 GPIO117_I2C_SCL, 128 GPIO118_I2C_SDA, 129 130 GPIO0_GPIO | WAKEUP_ON_EDGE_RISE, /* SPITZ_GPIO_KEY_INT */ 131 GPIO1_GPIO | WAKEUP_ON_EDGE_FALL, /* SPITZ_GPIO_RESET */ 132 }; 133 134 135 /****************************************************************************** 136 * Scoop GPIO expander 137 ******************************************************************************/ 138 #if defined(CONFIG_SHARP_SCOOP) || defined(CONFIG_SHARP_SCOOP_MODULE) 139 /* SCOOP Device #1 */ 140 static struct resource spitz_scoop_1_resources[] = { 141 [0] = { 142 .start = 0x10800000, 143 .end = 0x10800fff, 144 .flags = IORESOURCE_MEM, 145 }, 146 }; 147 148 static struct scoop_config spitz_scoop_1_setup = { 149 .io_dir = SPITZ_SCP_IO_DIR, 150 .io_out = SPITZ_SCP_IO_OUT, 151 .suspend_clr = SPITZ_SCP_SUS_CLR, 152 .suspend_set = SPITZ_SCP_SUS_SET, 153 .gpio_base = SPITZ_SCP_GPIO_BASE, 154 }; 155 156 struct platform_device spitz_scoop_1_device = { 157 .name = "sharp-scoop", 158 .id = 0, 159 .dev = { 160 .platform_data = &spitz_scoop_1_setup, 161 }, 162 .num_resources = ARRAY_SIZE(spitz_scoop_1_resources), 163 .resource = spitz_scoop_1_resources, 164 }; 165 166 /* SCOOP Device #2 */ 167 static struct resource spitz_scoop_2_resources[] = { 168 [0] = { 169 .start = 0x08800040, 170 .end = 0x08800fff, 171 .flags = IORESOURCE_MEM, 172 }, 173 }; 174 175 static struct scoop_config spitz_scoop_2_setup = { 176 .io_dir = SPITZ_SCP2_IO_DIR, 177 .io_out = SPITZ_SCP2_IO_OUT, 178 .suspend_clr = SPITZ_SCP2_SUS_CLR, 179 .suspend_set = SPITZ_SCP2_SUS_SET, 180 .gpio_base = SPITZ_SCP2_GPIO_BASE, 181 }; 182 183 struct platform_device spitz_scoop_2_device = { 184 .name = "sharp-scoop", 185 .id = 1, 186 .dev = { 187 .platform_data = &spitz_scoop_2_setup, 188 }, 189 .num_resources = ARRAY_SIZE(spitz_scoop_2_resources), 190 .resource = spitz_scoop_2_resources, 191 }; 192 193 static void __init spitz_scoop_init(void) 194 { 195 platform_device_register(&spitz_scoop_1_device); 196 197 /* Akita doesn't have the second SCOOP chip */ 198 if (!machine_is_akita()) 199 platform_device_register(&spitz_scoop_2_device); 200 } 201 202 /* Power control is shared with between one of the CF slots and SD */ 203 static void spitz_card_pwr_ctrl(uint8_t enable, uint8_t new_cpr) 204 { 205 unsigned short cpr; 206 unsigned long flags; 207 208 if (new_cpr & 0x7) { 209 gpio_set_value(SPITZ_GPIO_CF_POWER, 1); 210 mdelay(5); 211 } 212 213 local_irq_save(flags); 214 215 cpr = read_scoop_reg(&spitz_scoop_1_device.dev, SCOOP_CPR); 216 217 if (enable & new_cpr) 218 cpr |= new_cpr; 219 else 220 cpr &= ~enable; 221 222 write_scoop_reg(&spitz_scoop_1_device.dev, SCOOP_CPR, cpr); 223 224 local_irq_restore(flags); 225 226 if (!(cpr & 0x7)) { 227 mdelay(1); 228 gpio_set_value(SPITZ_GPIO_CF_POWER, 0); 229 } 230 } 231 232 #else 233 static inline void spitz_scoop_init(void) {} 234 static inline void spitz_card_pwr_ctrl(uint8_t enable, uint8_t new_cpr) {} 235 #endif 236 237 /****************************************************************************** 238 * PCMCIA 239 ******************************************************************************/ 240 #if defined(CONFIG_PCMCIA_PXA2XX) || defined(CONFIG_PCMCIA_PXA2XX_MODULE) 241 static void spitz_pcmcia_pwr(struct device *scoop, uint16_t cpr, int nr) 242 { 243 /* Only need to override behaviour for slot 0 */ 244 if (nr == 0) 245 spitz_card_pwr_ctrl( 246 cpr & (SCOOP_CPR_CF_3V | SCOOP_CPR_CF_XV), cpr); 247 else 248 write_scoop_reg(scoop, SCOOP_CPR, cpr); 249 } 250 251 static struct scoop_pcmcia_dev spitz_pcmcia_scoop[] = { 252 { 253 .dev = &spitz_scoop_1_device.dev, 254 .irq = SPITZ_IRQ_GPIO_CF_IRQ, 255 .cd_irq = SPITZ_IRQ_GPIO_CF_CD, 256 .cd_irq_str = "PCMCIA0 CD", 257 }, { 258 .dev = &spitz_scoop_2_device.dev, 259 .irq = SPITZ_IRQ_GPIO_CF2_IRQ, 260 .cd_irq = -1, 261 }, 262 }; 263 264 static struct scoop_pcmcia_config spitz_pcmcia_config = { 265 .devs = &spitz_pcmcia_scoop[0], 266 .num_devs = 2, 267 .power_ctrl = spitz_pcmcia_pwr, 268 }; 269 270 static void __init spitz_pcmcia_init(void) 271 { 272 /* Akita has only one PCMCIA slot used */ 273 if (machine_is_akita()) 274 spitz_pcmcia_config.num_devs = 1; 275 276 platform_scoop_config = &spitz_pcmcia_config; 277 } 278 #else 279 static inline void spitz_pcmcia_init(void) {} 280 #endif 281 282 /****************************************************************************** 283 * GPIO keyboard 284 ******************************************************************************/ 285 #if defined(CONFIG_KEYBOARD_MATRIX) || defined(CONFIG_KEYBOARD_MATRIX_MODULE) 286 287 #define SPITZ_KEY_CALENDAR KEY_F1 288 #define SPITZ_KEY_ADDRESS KEY_F2 289 #define SPITZ_KEY_FN KEY_F3 290 #define SPITZ_KEY_CANCEL KEY_F4 291 #define SPITZ_KEY_EXOK KEY_F5 292 #define SPITZ_KEY_EXCANCEL KEY_F6 293 #define SPITZ_KEY_EXJOGDOWN KEY_F7 294 #define SPITZ_KEY_EXJOGUP KEY_F8 295 #define SPITZ_KEY_JAP1 KEY_LEFTALT 296 #define SPITZ_KEY_JAP2 KEY_RIGHTCTRL 297 #define SPITZ_KEY_SYNC KEY_F9 298 #define SPITZ_KEY_MAIL KEY_F10 299 #define SPITZ_KEY_OK KEY_F11 300 #define SPITZ_KEY_MENU KEY_F12 301 302 static const uint32_t spitz_keymap[] = { 303 KEY(0, 0, KEY_LEFTCTRL), 304 KEY(0, 1, KEY_1), 305 KEY(0, 2, KEY_3), 306 KEY(0, 3, KEY_5), 307 KEY(0, 4, KEY_6), 308 KEY(0, 5, KEY_7), 309 KEY(0, 6, KEY_9), 310 KEY(0, 7, KEY_0), 311 KEY(0, 8, KEY_BACKSPACE), 312 KEY(0, 9, SPITZ_KEY_EXOK), /* EXOK */ 313 KEY(0, 10, SPITZ_KEY_EXCANCEL), /* EXCANCEL */ 314 KEY(1, 1, KEY_2), 315 KEY(1, 2, KEY_4), 316 KEY(1, 3, KEY_R), 317 KEY(1, 4, KEY_Y), 318 KEY(1, 5, KEY_8), 319 KEY(1, 6, KEY_I), 320 KEY(1, 7, KEY_O), 321 KEY(1, 8, KEY_P), 322 KEY(1, 9, SPITZ_KEY_EXJOGDOWN), /* EXJOGDOWN */ 323 KEY(1, 10, SPITZ_KEY_EXJOGUP), /* EXJOGUP */ 324 KEY(2, 0, KEY_TAB), 325 KEY(2, 1, KEY_Q), 326 KEY(2, 2, KEY_E), 327 KEY(2, 3, KEY_T), 328 KEY(2, 4, KEY_G), 329 KEY(2, 5, KEY_U), 330 KEY(2, 6, KEY_J), 331 KEY(2, 7, KEY_K), 332 KEY(3, 0, SPITZ_KEY_ADDRESS), /* ADDRESS */ 333 KEY(3, 1, KEY_W), 334 KEY(3, 2, KEY_S), 335 KEY(3, 3, KEY_F), 336 KEY(3, 4, KEY_V), 337 KEY(3, 5, KEY_H), 338 KEY(3, 6, KEY_M), 339 KEY(3, 7, KEY_L), 340 KEY(3, 9, KEY_RIGHTSHIFT), 341 KEY(4, 0, SPITZ_KEY_CALENDAR), /* CALENDAR */ 342 KEY(4, 1, KEY_A), 343 KEY(4, 2, KEY_D), 344 KEY(4, 3, KEY_C), 345 KEY(4, 4, KEY_B), 346 KEY(4, 5, KEY_N), 347 KEY(4, 6, KEY_DOT), 348 KEY(4, 8, KEY_ENTER), 349 KEY(4, 9, KEY_LEFTSHIFT), 350 KEY(5, 0, SPITZ_KEY_MAIL), /* MAIL */ 351 KEY(5, 1, KEY_Z), 352 KEY(5, 2, KEY_X), 353 KEY(5, 3, KEY_MINUS), 354 KEY(5, 4, KEY_SPACE), 355 KEY(5, 5, KEY_COMMA), 356 KEY(5, 7, KEY_UP), 357 KEY(5, 10, SPITZ_KEY_FN), /* FN */ 358 KEY(6, 0, KEY_SYSRQ), 359 KEY(6, 1, SPITZ_KEY_JAP1), /* JAP1 */ 360 KEY(6, 2, SPITZ_KEY_JAP2), /* JAP2 */ 361 KEY(6, 3, SPITZ_KEY_CANCEL), /* CANCEL */ 362 KEY(6, 4, SPITZ_KEY_OK), /* OK */ 363 KEY(6, 5, SPITZ_KEY_MENU), /* MENU */ 364 KEY(6, 6, KEY_LEFT), 365 KEY(6, 7, KEY_DOWN), 366 KEY(6, 8, KEY_RIGHT), 367 }; 368 369 static const struct matrix_keymap_data spitz_keymap_data = { 370 .keymap = spitz_keymap, 371 .keymap_size = ARRAY_SIZE(spitz_keymap), 372 }; 373 374 static const uint32_t spitz_row_gpios[] = 375 { 12, 17, 91, 34, 36, 38, 39 }; 376 static const uint32_t spitz_col_gpios[] = 377 { 88, 23, 24, 25, 26, 27, 52, 103, 107, 108, 114 }; 378 379 static struct matrix_keypad_platform_data spitz_mkp_pdata = { 380 .keymap_data = &spitz_keymap_data, 381 .row_gpios = spitz_row_gpios, 382 .col_gpios = spitz_col_gpios, 383 .num_row_gpios = ARRAY_SIZE(spitz_row_gpios), 384 .num_col_gpios = ARRAY_SIZE(spitz_col_gpios), 385 .col_scan_delay_us = 10, 386 .debounce_ms = 10, 387 .wakeup = 1, 388 }; 389 390 static struct platform_device spitz_mkp_device = { 391 .name = "matrix-keypad", 392 .id = -1, 393 .dev = { 394 .platform_data = &spitz_mkp_pdata, 395 }, 396 }; 397 398 static void __init spitz_mkp_init(void) 399 { 400 platform_device_register(&spitz_mkp_device); 401 } 402 #else 403 static inline void spitz_mkp_init(void) {} 404 #endif 405 406 /****************************************************************************** 407 * GPIO keys 408 ******************************************************************************/ 409 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) 410 static struct gpio_keys_button spitz_gpio_keys[] = { 411 { 412 .type = EV_PWR, 413 .code = KEY_SUSPEND, 414 .gpio = SPITZ_GPIO_ON_KEY, 415 .desc = "On Off", 416 .wakeup = 1, 417 }, 418 /* Two buttons detecting the lid state */ 419 { 420 .type = EV_SW, 421 .code = 0, 422 .gpio = SPITZ_GPIO_SWA, 423 .desc = "Display Down", 424 }, 425 { 426 .type = EV_SW, 427 .code = 1, 428 .gpio = SPITZ_GPIO_SWB, 429 .desc = "Lid Closed", 430 }, 431 }; 432 433 static struct gpio_keys_platform_data spitz_gpio_keys_platform_data = { 434 .buttons = spitz_gpio_keys, 435 .nbuttons = ARRAY_SIZE(spitz_gpio_keys), 436 }; 437 438 static struct platform_device spitz_gpio_keys_device = { 439 .name = "gpio-keys", 440 .id = -1, 441 .dev = { 442 .platform_data = &spitz_gpio_keys_platform_data, 443 }, 444 }; 445 446 static void __init spitz_keys_init(void) 447 { 448 platform_device_register(&spitz_gpio_keys_device); 449 } 450 #else 451 static inline void spitz_keys_init(void) {} 452 #endif 453 454 /****************************************************************************** 455 * LEDs 456 ******************************************************************************/ 457 #if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE) 458 static struct gpio_led spitz_gpio_leds[] = { 459 { 460 .name = "spitz:amber:charge", 461 .default_trigger = "sharpsl-charge", 462 .gpio = SPITZ_GPIO_LED_ORANGE, 463 }, 464 { 465 .name = "spitz:green:hddactivity", 466 .default_trigger = "ide-disk", 467 .gpio = SPITZ_GPIO_LED_GREEN, 468 }, 469 }; 470 471 static struct gpio_led_platform_data spitz_gpio_leds_info = { 472 .leds = spitz_gpio_leds, 473 .num_leds = ARRAY_SIZE(spitz_gpio_leds), 474 }; 475 476 static struct platform_device spitz_led_device = { 477 .name = "leds-gpio", 478 .id = -1, 479 .dev = { 480 .platform_data = &spitz_gpio_leds_info, 481 }, 482 }; 483 484 static void __init spitz_leds_init(void) 485 { 486 platform_device_register(&spitz_led_device); 487 } 488 #else 489 static inline void spitz_leds_init(void) {} 490 #endif 491 492 /****************************************************************************** 493 * SSP Devices 494 ******************************************************************************/ 495 #if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE) 496 static void spitz_ads7846_wait_for_hsync(void) 497 { 498 while (gpio_get_value(SPITZ_GPIO_HSYNC)) 499 cpu_relax(); 500 501 while (!gpio_get_value(SPITZ_GPIO_HSYNC)) 502 cpu_relax(); 503 } 504 505 static struct ads7846_platform_data spitz_ads7846_info = { 506 .model = 7846, 507 .vref_delay_usecs = 100, 508 .x_plate_ohms = 419, 509 .y_plate_ohms = 486, 510 .pressure_max = 1024, 511 .gpio_pendown = SPITZ_GPIO_TP_INT, 512 .wait_for_sync = spitz_ads7846_wait_for_hsync, 513 }; 514 515 static struct pxa2xx_spi_chip spitz_ads7846_chip = { 516 .gpio_cs = SPITZ_GPIO_ADS7846_CS, 517 }; 518 519 static void spitz_bl_kick_battery(void) 520 { 521 void (*kick_batt)(void); 522 523 kick_batt = symbol_get(sharpsl_battery_kick); 524 if (kick_batt) { 525 kick_batt(); 526 symbol_put(sharpsl_battery_kick); 527 } 528 } 529 530 static struct corgi_lcd_platform_data spitz_lcdcon_info = { 531 .init_mode = CORGI_LCD_MODE_VGA, 532 .max_intensity = 0x2f, 533 .default_intensity = 0x1f, 534 .limit_mask = 0x0b, 535 .gpio_backlight_cont = SPITZ_GPIO_BACKLIGHT_CONT, 536 .gpio_backlight_on = SPITZ_GPIO_BACKLIGHT_ON, 537 .kick_battery = spitz_bl_kick_battery, 538 }; 539 540 static struct pxa2xx_spi_chip spitz_lcdcon_chip = { 541 .gpio_cs = SPITZ_GPIO_LCDCON_CS, 542 }; 543 544 static struct pxa2xx_spi_chip spitz_max1111_chip = { 545 .gpio_cs = SPITZ_GPIO_MAX1111_CS, 546 }; 547 548 static struct spi_board_info spitz_spi_devices[] = { 549 { 550 .modalias = "ads7846", 551 .max_speed_hz = 1200000, 552 .bus_num = 2, 553 .chip_select = 0, 554 .platform_data = &spitz_ads7846_info, 555 .controller_data = &spitz_ads7846_chip, 556 .irq = PXA_GPIO_TO_IRQ(SPITZ_GPIO_TP_INT), 557 }, { 558 .modalias = "corgi-lcd", 559 .max_speed_hz = 50000, 560 .bus_num = 2, 561 .chip_select = 1, 562 .platform_data = &spitz_lcdcon_info, 563 .controller_data = &spitz_lcdcon_chip, 564 }, { 565 .modalias = "max1111", 566 .max_speed_hz = 450000, 567 .bus_num = 2, 568 .chip_select = 2, 569 .controller_data = &spitz_max1111_chip, 570 }, 571 }; 572 573 static struct pxa2xx_spi_master spitz_spi_info = { 574 .num_chipselect = 3, 575 }; 576 577 static void __init spitz_spi_init(void) 578 { 579 struct corgi_lcd_platform_data *lcd_data = &spitz_lcdcon_info; 580 581 if (machine_is_akita()) { 582 lcd_data->gpio_backlight_cont = AKITA_GPIO_BACKLIGHT_CONT; 583 lcd_data->gpio_backlight_on = AKITA_GPIO_BACKLIGHT_ON; 584 } 585 586 pxa2xx_set_spi_info(2, &spitz_spi_info); 587 spi_register_board_info(ARRAY_AND_SIZE(spitz_spi_devices)); 588 } 589 #else 590 static inline void spitz_spi_init(void) {} 591 #endif 592 593 /****************************************************************************** 594 * SD/MMC card controller 595 ******************************************************************************/ 596 #if defined(CONFIG_MMC_PXA) || defined(CONFIG_MMC_PXA_MODULE) 597 /* 598 * NOTE: The card detect interrupt isn't debounced so we delay it by 250ms to 599 * give the card a chance to fully insert/eject. 600 */ 601 static int spitz_mci_setpower(struct device *dev, unsigned int vdd) 602 { 603 struct pxamci_platform_data* p_d = dev->platform_data; 604 605 if ((1 << vdd) & p_d->ocr_mask) 606 spitz_card_pwr_ctrl(SCOOP_CPR_SD_3V, SCOOP_CPR_SD_3V); 607 else 608 spitz_card_pwr_ctrl(SCOOP_CPR_SD_3V, 0x0); 609 610 return 0; 611 } 612 613 static struct pxamci_platform_data spitz_mci_platform_data = { 614 .detect_delay_ms = 250, 615 .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34, 616 .setpower = spitz_mci_setpower, 617 .gpio_card_detect = SPITZ_GPIO_nSD_DETECT, 618 .gpio_card_ro = SPITZ_GPIO_nSD_WP, 619 .gpio_power = -1, 620 }; 621 622 static void __init spitz_mmc_init(void) 623 { 624 pxa_set_mci_info(&spitz_mci_platform_data); 625 } 626 #else 627 static inline void spitz_mmc_init(void) {} 628 #endif 629 630 /****************************************************************************** 631 * USB Host 632 ******************************************************************************/ 633 #if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) 634 static int spitz_ohci_init(struct device *dev) 635 { 636 int err; 637 638 err = gpio_request(SPITZ_GPIO_USB_HOST, "USB_HOST"); 639 if (err) 640 return err; 641 642 /* Only Port 2 is connected, setup USB Port 2 Output Control Register */ 643 UP2OCR = UP2OCR_HXS | UP2OCR_HXOE | UP2OCR_DPPDE | UP2OCR_DMPDE; 644 645 return gpio_direction_output(SPITZ_GPIO_USB_HOST, 1); 646 } 647 648 static void spitz_ohci_exit(struct device *dev) 649 { 650 gpio_free(SPITZ_GPIO_USB_HOST); 651 } 652 653 static struct pxaohci_platform_data spitz_ohci_platform_data = { 654 .port_mode = PMM_NPS_MODE, 655 .init = spitz_ohci_init, 656 .exit = spitz_ohci_exit, 657 .flags = ENABLE_PORT_ALL | NO_OC_PROTECTION, 658 .power_budget = 150, 659 }; 660 661 static void __init spitz_uhc_init(void) 662 { 663 pxa_set_ohci_info(&spitz_ohci_platform_data); 664 } 665 #else 666 static inline void spitz_uhc_init(void) {} 667 #endif 668 669 /****************************************************************************** 670 * IrDA 671 ******************************************************************************/ 672 #if defined(CONFIG_PXA_FICP) || defined(CONFIG_PXA_FICP_MODULE) 673 static struct pxaficp_platform_data spitz_ficp_platform_data = { 674 .transceiver_cap = IR_SIRMODE | IR_OFF, 675 }; 676 677 static void __init spitz_irda_init(void) 678 { 679 if (machine_is_akita()) 680 spitz_ficp_platform_data.gpio_pwdown = AKITA_GPIO_IR_ON; 681 else 682 spitz_ficp_platform_data.gpio_pwdown = SPITZ_GPIO_IR_ON; 683 684 pxa_set_ficp_info(&spitz_ficp_platform_data); 685 } 686 #else 687 static inline void spitz_irda_init(void) {} 688 #endif 689 690 /****************************************************************************** 691 * Framebuffer 692 ******************************************************************************/ 693 #if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE) 694 static struct pxafb_mode_info spitz_pxafb_modes[] = { 695 { 696 .pixclock = 19231, 697 .xres = 480, 698 .yres = 640, 699 .bpp = 16, 700 .hsync_len = 40, 701 .left_margin = 46, 702 .right_margin = 125, 703 .vsync_len = 3, 704 .upper_margin = 1, 705 .lower_margin = 0, 706 .sync = 0, 707 }, { 708 .pixclock = 134617, 709 .xres = 240, 710 .yres = 320, 711 .bpp = 16, 712 .hsync_len = 20, 713 .left_margin = 20, 714 .right_margin = 46, 715 .vsync_len = 2, 716 .upper_margin = 1, 717 .lower_margin = 0, 718 .sync = 0, 719 }, 720 }; 721 722 static struct pxafb_mach_info spitz_pxafb_info = { 723 .modes = spitz_pxafb_modes, 724 .num_modes = ARRAY_SIZE(spitz_pxafb_modes), 725 .fixed_modes = 1, 726 .lcd_conn = LCD_COLOR_TFT_16BPP | LCD_ALTERNATE_MAPPING, 727 }; 728 729 static void __init spitz_lcd_init(void) 730 { 731 pxa_set_fb_info(NULL, &spitz_pxafb_info); 732 } 733 #else 734 static inline void spitz_lcd_init(void) {} 735 #endif 736 737 /****************************************************************************** 738 * NAND Flash 739 ******************************************************************************/ 740 #if defined(CONFIG_MTD_NAND_SHARPSL) || defined(CONFIG_MTD_NAND_SHARPSL_MODULE) 741 static struct mtd_partition spitz_nand_partitions[] = { 742 { 743 .name = "System Area", 744 .offset = 0, 745 .size = 7 * 1024 * 1024, 746 }, { 747 .name = "Root Filesystem", 748 .offset = 7 * 1024 * 1024, 749 }, { 750 .name = "Home Filesystem", 751 .offset = MTDPART_OFS_APPEND, 752 .size = MTDPART_SIZ_FULL, 753 }, 754 }; 755 756 static uint8_t scan_ff_pattern[] = { 0xff, 0xff }; 757 758 static struct nand_bbt_descr spitz_nand_bbt = { 759 .options = 0, 760 .offs = 4, 761 .len = 2, 762 .pattern = scan_ff_pattern 763 }; 764 765 static struct nand_ecclayout akita_oobinfo = { 766 .oobfree = { {0x08, 0x09} }, 767 .eccbytes = 24, 768 .eccpos = { 769 0x05, 0x01, 0x02, 0x03, 0x06, 0x07, 0x15, 0x11, 770 0x12, 0x13, 0x16, 0x17, 0x25, 0x21, 0x22, 0x23, 771 0x26, 0x27, 0x35, 0x31, 0x32, 0x33, 0x36, 0x37, 772 }, 773 }; 774 775 static struct sharpsl_nand_platform_data spitz_nand_pdata = { 776 .badblock_pattern = &spitz_nand_bbt, 777 .partitions = spitz_nand_partitions, 778 .nr_partitions = ARRAY_SIZE(spitz_nand_partitions), 779 }; 780 781 static struct resource spitz_nand_resources[] = { 782 { 783 .start = PXA_CS3_PHYS, 784 .end = PXA_CS3_PHYS + SZ_4K - 1, 785 .flags = IORESOURCE_MEM, 786 }, 787 }; 788 789 static struct platform_device spitz_nand_device = { 790 .name = "sharpsl-nand", 791 .id = -1, 792 .resource = spitz_nand_resources, 793 .num_resources = ARRAY_SIZE(spitz_nand_resources), 794 .dev = { 795 .platform_data = &spitz_nand_pdata, 796 } 797 }; 798 799 static void __init spitz_nand_init(void) 800 { 801 if (machine_is_spitz()) { 802 spitz_nand_partitions[1].size = 5 * 1024 * 1024; 803 } else if (machine_is_akita()) { 804 spitz_nand_partitions[1].size = 58 * 1024 * 1024; 805 spitz_nand_bbt.len = 1; 806 spitz_nand_pdata.ecc_layout = &akita_oobinfo; 807 } else if (machine_is_borzoi()) { 808 spitz_nand_partitions[1].size = 32 * 1024 * 1024; 809 spitz_nand_bbt.len = 1; 810 spitz_nand_pdata.ecc_layout = &akita_oobinfo; 811 } 812 813 platform_device_register(&spitz_nand_device); 814 } 815 #else 816 static inline void spitz_nand_init(void) {} 817 #endif 818 819 /****************************************************************************** 820 * NOR Flash 821 ******************************************************************************/ 822 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE) 823 static struct mtd_partition spitz_rom_parts[] = { 824 { 825 .name ="Boot PROM Filesystem", 826 .offset = 0x00140000, 827 .size = MTDPART_SIZ_FULL, 828 }, 829 }; 830 831 static struct physmap_flash_data spitz_rom_data = { 832 .width = 2, 833 .nr_parts = ARRAY_SIZE(spitz_rom_parts), 834 .parts = spitz_rom_parts, 835 }; 836 837 static struct resource spitz_rom_resources[] = { 838 { 839 .start = PXA_CS0_PHYS, 840 .end = PXA_CS0_PHYS + SZ_8M - 1, 841 .flags = IORESOURCE_MEM, 842 }, 843 }; 844 845 static struct platform_device spitz_rom_device = { 846 .name = "physmap-flash", 847 .id = -1, 848 .resource = spitz_rom_resources, 849 .num_resources = ARRAY_SIZE(spitz_rom_resources), 850 .dev = { 851 .platform_data = &spitz_rom_data, 852 }, 853 }; 854 855 static void __init spitz_nor_init(void) 856 { 857 platform_device_register(&spitz_rom_device); 858 } 859 #else 860 static inline void spitz_nor_init(void) {} 861 #endif 862 863 /****************************************************************************** 864 * I2C devices 865 ******************************************************************************/ 866 #if defined(CONFIG_I2C_PXA) || defined(CONFIG_I2C_PXA_MODULE) 867 static struct pca953x_platform_data akita_pca953x_pdata = { 868 .gpio_base = AKITA_IOEXP_GPIO_BASE, 869 }; 870 871 static struct i2c_board_info spitz_i2c_devs[] = { 872 { 873 .type = "wm8750", 874 .addr = 0x1b, 875 }, { 876 .type = "max7310", 877 .addr = 0x18, 878 .platform_data = &akita_pca953x_pdata, 879 }, 880 }; 881 882 static struct regulator_consumer_supply isl6271a_consumers[] = { 883 REGULATOR_SUPPLY("vcc_core", NULL), 884 }; 885 886 static struct regulator_init_data isl6271a_info[] = { 887 { 888 .constraints = { 889 .name = "vcc_core range", 890 .min_uV = 850000, 891 .max_uV = 1600000, 892 .always_on = 1, 893 .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE, 894 }, 895 .consumer_supplies = isl6271a_consumers, 896 .num_consumer_supplies = ARRAY_SIZE(isl6271a_consumers), 897 } 898 }; 899 900 static struct i2c_board_info spitz_pi2c_devs[] = { 901 { 902 .type = "isl6271a", 903 .addr = 0x0c, 904 .platform_data = &isl6271a_info, 905 }, 906 }; 907 908 static void __init spitz_i2c_init(void) 909 { 910 int size = ARRAY_SIZE(spitz_i2c_devs); 911 912 /* Only Akita has the max7310 chip */ 913 if (!machine_is_akita()) 914 size--; 915 916 pxa_set_i2c_info(NULL); 917 pxa27x_set_i2c_power_info(NULL); 918 i2c_register_board_info(0, spitz_i2c_devs, size); 919 i2c_register_board_info(1, ARRAY_AND_SIZE(spitz_pi2c_devs)); 920 } 921 #else 922 static inline void spitz_i2c_init(void) {} 923 #endif 924 925 /****************************************************************************** 926 * Machine init 927 ******************************************************************************/ 928 static void spitz_poweroff(void) 929 { 930 pxa_restart(REBOOT_GPIO, NULL); 931 } 932 933 static void spitz_restart(enum reboot_mode mode, const char *cmd) 934 { 935 uint32_t msc0 = __raw_readl(MSC0); 936 /* Bootloader magic for a reboot */ 937 if ((msc0 & 0xffff0000) == 0x7ff00000) 938 __raw_writel((msc0 & 0xffff) | 0x7ee00000, MSC0); 939 940 spitz_poweroff(); 941 } 942 943 static void __init spitz_init(void) 944 { 945 init_gpio_reset(SPITZ_GPIO_ON_RESET, 1, 0); 946 pm_power_off = spitz_poweroff; 947 948 PMCR = 0x00; 949 950 /* Stop 3.6MHz and drive HIGH to PCMCIA and CS */ 951 PCFR |= PCFR_OPDE; 952 953 pxa2xx_mfp_config(ARRAY_AND_SIZE(spitz_pin_config)); 954 955 pxa_set_ffuart_info(NULL); 956 pxa_set_btuart_info(NULL); 957 pxa_set_stuart_info(NULL); 958 959 spitz_spi_init(); 960 spitz_scoop_init(); 961 spitz_mkp_init(); 962 spitz_keys_init(); 963 spitz_leds_init(); 964 spitz_mmc_init(); 965 spitz_pcmcia_init(); 966 spitz_irda_init(); 967 spitz_uhc_init(); 968 spitz_lcd_init(); 969 spitz_nor_init(); 970 spitz_nand_init(); 971 spitz_i2c_init(); 972 } 973 974 static void __init spitz_fixup(struct tag *tags, char **cmdline, 975 struct meminfo *mi) 976 { 977 sharpsl_save_param(); 978 mi->nr_banks = 1; 979 mi->bank[0].start = 0xa0000000; 980 mi->bank[0].size = (64*1024*1024); 981 } 982 983 #ifdef CONFIG_MACH_SPITZ 984 MACHINE_START(SPITZ, "SHARP Spitz") 985 .fixup = spitz_fixup, 986 .map_io = pxa27x_map_io, 987 .nr_irqs = PXA_NR_IRQS, 988 .init_irq = pxa27x_init_irq, 989 .handle_irq = pxa27x_handle_irq, 990 .init_machine = spitz_init, 991 .init_time = pxa_timer_init, 992 .restart = spitz_restart, 993 MACHINE_END 994 #endif 995 996 #ifdef CONFIG_MACH_BORZOI 997 MACHINE_START(BORZOI, "SHARP Borzoi") 998 .fixup = spitz_fixup, 999 .map_io = pxa27x_map_io, 1000 .nr_irqs = PXA_NR_IRQS, 1001 .init_irq = pxa27x_init_irq, 1002 .handle_irq = pxa27x_handle_irq, 1003 .init_machine = spitz_init, 1004 .init_time = pxa_timer_init, 1005 .restart = spitz_restart, 1006 MACHINE_END 1007 #endif 1008 1009 #ifdef CONFIG_MACH_AKITA 1010 MACHINE_START(AKITA, "SHARP Akita") 1011 .fixup = spitz_fixup, 1012 .map_io = pxa27x_map_io, 1013 .nr_irqs = PXA_NR_IRQS, 1014 .init_irq = pxa27x_init_irq, 1015 .handle_irq = pxa27x_handle_irq, 1016 .init_machine = spitz_init, 1017 .init_time = pxa_timer_init, 1018 .restart = spitz_restart, 1019 MACHINE_END 1020 #endif 1021