1 /* 2 * linux/arch/arm/mach-pxa/gumstix.c 3 * 4 * Support for the Gumstix motherboards. 5 * 6 * Original Author: Craig Hughes 7 * Created: Feb 14, 2008 8 * Copyright: Craig Hughes 9 * 10 * This program is free software; you can redistribute it and/or modify 11 * it under the terms of the GNU General Public License version 2 as 12 * published by the Free Software Foundation. 13 * 14 * Implemented based on lubbock.c by Nicolas Pitre and code from Craig 15 * Hughes 16 */ 17 18 #include <linux/module.h> 19 #include <linux/kernel.h> 20 #include <linux/init.h> 21 #include <linux/platform_device.h> 22 #include <linux/interrupt.h> 23 #include <linux/delay.h> 24 #include <linux/mtd/mtd.h> 25 #include <linux/mtd/partitions.h> 26 #include <linux/gpio.h> 27 #include <linux/err.h> 28 #include <linux/clk.h> 29 #include <linux/usb/gpio_vbus.h> 30 31 #include <asm/setup.h> 32 #include <asm/memory.h> 33 #include <asm/mach-types.h> 34 #include <mach/hardware.h> 35 #include <asm/irq.h> 36 #include <asm/sizes.h> 37 38 #include <asm/mach/arch.h> 39 #include <asm/mach/map.h> 40 #include <asm/mach/irq.h> 41 #include <asm/mach/flash.h> 42 43 #include "pxa25x.h" 44 #include <linux/platform_data/mmc-pxamci.h> 45 #include "udc.h" 46 #include "gumstix.h" 47 48 #include "generic.h" 49 50 static struct resource flash_resource = { 51 .start = 0x00000000, 52 .end = SZ_64M - 1, 53 .flags = IORESOURCE_MEM, 54 }; 55 56 static struct mtd_partition gumstix_partitions[] = { 57 { 58 .name = "Bootloader", 59 .size = 0x00040000, 60 .offset = 0, 61 .mask_flags = MTD_WRITEABLE /* force read-only */ 62 } , { 63 .name = "rootfs", 64 .size = MTDPART_SIZ_FULL, 65 .offset = MTDPART_OFS_APPEND 66 } 67 }; 68 69 static struct flash_platform_data gumstix_flash_data = { 70 .map_name = "cfi_probe", 71 .parts = gumstix_partitions, 72 .nr_parts = ARRAY_SIZE(gumstix_partitions), 73 .width = 2, 74 }; 75 76 static struct platform_device gumstix_flash_device = { 77 .name = "pxa2xx-flash", 78 .id = 0, 79 .dev = { 80 .platform_data = &gumstix_flash_data, 81 }, 82 .resource = &flash_resource, 83 .num_resources = 1, 84 }; 85 86 static struct platform_device *devices[] __initdata = { 87 &gumstix_flash_device, 88 }; 89 90 #ifdef CONFIG_MMC_PXA 91 static struct pxamci_platform_data gumstix_mci_platform_data = { 92 .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34, 93 .gpio_card_detect = -1, 94 .gpio_card_ro = -1, 95 .gpio_power = -1, 96 }; 97 98 static void __init gumstix_mmc_init(void) 99 { 100 pxa_set_mci_info(&gumstix_mci_platform_data); 101 } 102 #else 103 static void __init gumstix_mmc_init(void) 104 { 105 pr_debug("Gumstix mmc disabled\n"); 106 } 107 #endif 108 109 #ifdef CONFIG_USB_PXA25X 110 static struct gpio_vbus_mach_info gumstix_udc_info = { 111 .gpio_vbus = GPIO_GUMSTIX_USB_GPIOn, 112 .gpio_pullup = GPIO_GUMSTIX_USB_GPIOx, 113 }; 114 115 static struct platform_device gumstix_gpio_vbus = { 116 .name = "gpio-vbus", 117 .id = -1, 118 .dev = { 119 .platform_data = &gumstix_udc_info, 120 }, 121 }; 122 123 static void __init gumstix_udc_init(void) 124 { 125 platform_device_register(&gumstix_gpio_vbus); 126 } 127 #else 128 static void gumstix_udc_init(void) 129 { 130 pr_debug("Gumstix udc is disabled\n"); 131 } 132 #endif 133 134 #ifdef CONFIG_BT 135 /* Normally, the bootloader would have enabled this 32kHz clock but many 136 ** boards still have u-boot 1.1.4 so we check if it has been turned on and 137 ** if not, we turn it on with a warning message. */ 138 static void gumstix_setup_bt_clock(void) 139 { 140 int timeout = 500; 141 142 if (!(readl(OSCC) & OSCC_OOK)) 143 pr_warn("32kHz clock was not on. Bootloader may need to be updated\n"); 144 else 145 return; 146 147 writel(readl(OSCC) | OSCC_OON, OSCC); 148 do { 149 if (readl(OSCC) & OSCC_OOK) 150 break; 151 udelay(1); 152 } while (--timeout); 153 if (!timeout) 154 pr_err("Failed to start 32kHz clock\n"); 155 } 156 157 static void __init gumstix_bluetooth_init(void) 158 { 159 int err; 160 161 gumstix_setup_bt_clock(); 162 163 err = gpio_request(GPIO_GUMSTIX_BTRESET, "BTRST"); 164 if (err) { 165 pr_err("gumstix: failed request gpio for bluetooth reset\n"); 166 return; 167 } 168 169 err = gpio_direction_output(GPIO_GUMSTIX_BTRESET, 1); 170 if (err) { 171 pr_err("gumstix: can't reset bluetooth\n"); 172 return; 173 } 174 gpio_set_value(GPIO_GUMSTIX_BTRESET, 0); 175 udelay(100); 176 gpio_set_value(GPIO_GUMSTIX_BTRESET, 1); 177 } 178 #else 179 static void gumstix_bluetooth_init(void) 180 { 181 pr_debug("Gumstix Bluetooth is disabled\n"); 182 } 183 #endif 184 185 static unsigned long gumstix_pin_config[] __initdata = { 186 GPIO12_32KHz, 187 /* BTUART */ 188 GPIO42_HWUART_RXD, 189 GPIO43_HWUART_TXD, 190 GPIO44_HWUART_CTS, 191 GPIO45_HWUART_RTS, 192 /* MMC */ 193 GPIO6_MMC_CLK, 194 GPIO53_MMC_CLK, 195 GPIO8_MMC_CS0, 196 }; 197 198 int __attribute__((weak)) am200_init(void) 199 { 200 return 0; 201 } 202 203 int __attribute__((weak)) am300_init(void) 204 { 205 return 0; 206 } 207 208 static void __init carrier_board_init(void) 209 { 210 /* 211 * put carrier/expansion board init here if 212 * they cannot be detected programatically 213 */ 214 am200_init(); 215 am300_init(); 216 } 217 218 static void __init gumstix_init(void) 219 { 220 pxa2xx_mfp_config(ARRAY_AND_SIZE(gumstix_pin_config)); 221 222 pxa_set_ffuart_info(NULL); 223 pxa_set_btuart_info(NULL); 224 pxa_set_stuart_info(NULL); 225 pxa_set_hwuart_info(NULL); 226 227 gumstix_bluetooth_init(); 228 gumstix_udc_init(); 229 gumstix_mmc_init(); 230 (void) platform_add_devices(devices, ARRAY_SIZE(devices)); 231 carrier_board_init(); 232 } 233 234 MACHINE_START(GUMSTIX, "Gumstix") 235 .atag_offset = 0x100, /* match u-boot bi_boot_params */ 236 .map_io = pxa25x_map_io, 237 .nr_irqs = PXA_NR_IRQS, 238 .init_irq = pxa25x_init_irq, 239 .handle_irq = pxa25x_handle_irq, 240 .init_time = pxa_timer_init, 241 .init_machine = gumstix_init, 242 .restart = pxa_restart, 243 MACHINE_END 244