1/* 2 * linux/arch/arm/mach-omap2/sram243x.S 3 * 4 * Omap2 specific functions that need to be run in internal SRAM 5 * 6 * (C) Copyright 2004 7 * Texas Instruments, <www.ti.com> 8 * Richard Woodruff <r-woodruff2@ti.com> 9 * 10 * This program is free software; you can redistribute it and/or 11 * modify it under the terms of the GNU General Public License as 12 * published by the Free Software Foundation; either version 2 of 13 * the License, or (at your option) any later version. 14 * 15 * This program is distributed in the hope that it will be useful, 16 * but WITHOUT ANY WARRANTY; without even the implied warranty of 17 * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the 18 * GNU General Public License for more details. 19 * 20 * You should have received a copy of the GNU General Public License 21 * along with this program; if not, write to the Free Software 22 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 23 * MA 02111-1307 USA 24 * 25 * Richard Woodruff notes that any changes to this code must be carefully 26 * audited and tested to ensure that they don't cause a TLB miss while 27 * the SDRAM is inaccessible. Such a situation will crash the system 28 * since it will cause the ARM MMU to attempt to walk the page tables. 29 * These crashes may be intermittent. 30 */ 31#include <linux/linkage.h> 32 33#include <asm/assembler.h> 34 35#include "soc.h" 36#include "iomap.h" 37#include "prm2xxx.h" 38#include "cm2xxx.h" 39#include "sdrc.h" 40 41 .text 42 43 .align 3 44ENTRY(omap243x_sram_ddr_init) 45 stmfd sp!, {r0 - r12, lr} @ save registers on stack 46 47 mov r12, r2 @ capture CS1 vs CS0 48 mov r8, r3 @ capture force parameter 49 50 /* frequency shift down */ 51 ldr r2, omap243x_sdi_cm_clksel2_pll @ get address of dpllout reg 52 mov r3, #0x1 @ value for 1x operation 53 str r3, [r2] @ go to L1-freq operation 54 55 /* voltage shift down */ 56 mov r9, #0x1 @ set up for L1 voltage call 57 bl voltage_shift @ go drop voltage 58 59 /* dll lock mode */ 60 ldr r11, omap243x_sdi_sdrc_dlla_ctrl @ addr of dlla ctrl 61 ldr r10, [r11] @ get current val 62 cmp r12, #0x1 @ cs1 base (2422 es2.05/1) 63 addeq r11, r11, #0x8 @ if cs1 base, move to DLLB 64 mvn r9, #0x4 @ mask to get clear bit2 65 and r10, r10, r9 @ clear bit2 for lock mode. 66 orr r10, r10, #0x8 @ make sure DLL on (es2 bit pos) 67 orr r10, r10, #0x2 @ 90 degree phase for all below 133Mhz 68 str r10, [r11] @ commit to DLLA_CTRL 69 bl i_dll_wait @ wait for dll to lock 70 71 /* get dll value */ 72 add r11, r11, #0x4 @ get addr of status reg 73 ldr r10, [r11] @ get locked value 74 75 /* voltage shift up */ 76 mov r9, #0x0 @ shift back to L0-voltage 77 bl voltage_shift @ go raise voltage 78 79 /* frequency shift up */ 80 mov r3, #0x2 @ value for 2x operation 81 str r3, [r2] @ go to L0-freq operation 82 83 /* reset entry mode for dllctrl */ 84 sub r11, r11, #0x4 @ move from status to ctrl 85 cmp r12, #0x1 @ normalize if cs1 based 86 subeq r11, r11, #0x8 @ possibly back to DLLA 87 cmp r8, #0x1 @ if forced unlock exit 88 orreq r1, r1, #0x4 @ make sure exit with unlocked value 89 str r1, [r11] @ restore DLLA_CTRL high value 90 add r11, r11, #0x8 @ move to DLLB_CTRL addr 91 str r1, [r11] @ set value DLLB_CTRL 92 bl i_dll_wait @ wait for possible lock 93 94 /* set up for return, DDR should be good */ 95 str r10, [r0] @ write dll_status and return counter 96 ldmfd sp!, {r0 - r12, pc} @ restore regs and return 97 98 /* ensure the DLL has relocked */ 99i_dll_wait: 100 mov r4, #0x800 @ delay DLL relock, min 0x400 L3 clocks 101i_dll_delay: 102 subs r4, r4, #0x1 103 bne i_dll_delay 104 ret lr 105 106 /* 107 * shift up or down voltage, use R9 as input to tell level. 108 * wait for it to finish, use 32k sync counter, 1tick=31uS. 109 */ 110voltage_shift: 111 ldr r4, omap243x_sdi_prcm_voltctrl @ get addr of volt ctrl. 112 ldr r5, [r4] @ get value. 113 ldr r6, prcm_mask_val @ get value of mask 114 and r5, r5, r6 @ apply mask to clear bits 115 orr r5, r5, r9 @ bulld value for L0/L1-volt operation. 116 str r5, [r4] @ set up for change. 117 mov r3, #0x4000 @ get val for force 118 orr r5, r5, r3 @ build value for force 119 str r5, [r4] @ Force transition to L1 120 121 ldr r3, omap243x_sdi_timer_32ksynct_cr @ get addr of counter 122 ldr r5, [r3] @ get value 123 add r5, r5, #0x3 @ give it at most 93uS 124volt_delay: 125 ldr r7, [r3] @ get timer value 126 cmp r5, r7 @ time up? 127 bhi volt_delay @ not yet->branch 128 ret lr @ back to caller. 129 130omap243x_sdi_cm_clksel2_pll: 131 .word OMAP2430_CM_REGADDR(PLL_MOD, CM_CLKSEL2) 132omap243x_sdi_sdrc_dlla_ctrl: 133 .word OMAP243X_SDRC_REGADDR(SDRC_DLLA_CTRL) 134omap243x_sdi_prcm_voltctrl: 135 .word OMAP2430_PRCM_VOLTCTRL 136prcm_mask_val: 137 .word 0xFFFF3FFC 138omap243x_sdi_timer_32ksynct_cr: 139 .word OMAP2_L4_IO_ADDRESS(OMAP2430_32KSYNCT_BASE + 0x010) 140ENTRY(omap243x_sram_ddr_init_sz) 141 .word . - omap243x_sram_ddr_init 142 143/* 144 * Reprograms memory timings. 145 * r0 = [PRCM_FULL | PRCM_HALF] r1 = SDRC_DLLA_CTRL value r2 = [DDR | SDR] 146 * PRCM_FULL = 2, PRCM_HALF = 1, DDR = 1, SDR = 0 147 */ 148 .align 3 149ENTRY(omap243x_sram_reprogram_sdrc) 150 stmfd sp!, {r0 - r10, lr} @ save registers on stack 151 mov r3, #0x0 @ clear for mrc call 152 mcr p15, 0, r3, c7, c10, 4 @ memory barrier, finish ARM SDR/DDR 153 nop 154 nop 155 ldr r6, omap243x_srs_sdrc_rfr_ctrl @ get addr of refresh reg 156 ldr r5, [r6] @ get value 157 mov r5, r5, lsr #8 @ isolate rfr field and drop burst 158 159 cmp r0, #0x1 @ going to half speed? 160 movne r9, #0x0 @ if up set flag up for pre up, hi volt 161 162 blne voltage_shift_c @ adjust voltage 163 164 cmp r0, #0x1 @ going to half speed (post branch link) 165 moveq r5, r5, lsr #1 @ divide by 2 if to half 166 movne r5, r5, lsl #1 @ mult by 2 if to full 167 mov r5, r5, lsl #8 @ put rfr field back into place 168 add r5, r5, #0x1 @ turn on burst of 1 169 ldr r4, omap243x_srs_cm_clksel2_pll @ get address of out reg 170 ldr r3, [r4] @ get curr value 171 orr r3, r3, #0x3 172 bic r3, r3, #0x3 @ clear lower bits 173 orr r3, r3, r0 @ new state value 174 str r3, [r4] @ set new state (pll/x, x=1 or 2) 175 nop 176 nop 177 178 moveq r9, #0x1 @ if speed down, post down, drop volt 179 bleq voltage_shift_c 180 181 mcr p15, 0, r3, c7, c10, 4 @ memory barrier 182 str r5, [r6] @ set new RFR_1 value 183 add r6, r6, #0x30 @ get RFR_2 addr 184 str r5, [r6] @ set RFR_2 185 nop 186 cmp r2, #0x1 @ (SDR or DDR) do we need to adjust DLL 187 bne freq_out @ leave if SDR, no DLL function 188 189 /* With DDR, we need to take care of the DLL for the frequency change */ 190 ldr r2, omap243x_srs_sdrc_dlla_ctrl @ addr of dlla ctrl 191 str r1, [r2] @ write out new SDRC_DLLA_CTRL 192 add r2, r2, #0x8 @ addr to SDRC_DLLB_CTRL 193 str r1, [r2] @ commit to SDRC_DLLB_CTRL 194 mov r1, #0x2000 @ wait DLL relock, min 0x400 L3 clocks 195dll_wait: 196 subs r1, r1, #0x1 197 bne dll_wait 198freq_out: 199 ldmfd sp!, {r0 - r10, pc} @ restore regs and return 200 201 /* 202 * shift up or down voltage, use R9 as input to tell level. 203 * wait for it to finish, use 32k sync counter, 1tick=31uS. 204 */ 205voltage_shift_c: 206 ldr r10, omap243x_srs_prcm_voltctrl @ get addr of volt ctrl 207 ldr r8, [r10] @ get value 208 ldr r7, ddr_prcm_mask_val @ get value of mask 209 and r8, r8, r7 @ apply mask to clear bits 210 orr r8, r8, r9 @ bulld value for L0/L1-volt operation. 211 str r8, [r10] @ set up for change. 212 mov r7, #0x4000 @ get val for force 213 orr r8, r8, r7 @ build value for force 214 str r8, [r10] @ Force transition to L1 215 216 ldr r10, omap243x_srs_timer_32ksynct @ get addr of counter 217 ldr r8, [r10] @ get value 218 add r8, r8, #0x2 @ give it at most 62uS (min 31+) 219volt_delay_c: 220 ldr r7, [r10] @ get timer value 221 cmp r8, r7 @ time up? 222 bhi volt_delay_c @ not yet->branch 223 ret lr @ back to caller 224 225omap243x_srs_cm_clksel2_pll: 226 .word OMAP2430_CM_REGADDR(PLL_MOD, CM_CLKSEL2) 227omap243x_srs_sdrc_dlla_ctrl: 228 .word OMAP243X_SDRC_REGADDR(SDRC_DLLA_CTRL) 229omap243x_srs_sdrc_rfr_ctrl: 230 .word OMAP243X_SDRC_REGADDR(SDRC_RFR_CTRL_0) 231omap243x_srs_prcm_voltctrl: 232 .word OMAP2430_PRCM_VOLTCTRL 233ddr_prcm_mask_val: 234 .word 0xFFFF3FFC 235omap243x_srs_timer_32ksynct: 236 .word OMAP2_L4_IO_ADDRESS(OMAP2430_32KSYNCT_BASE + 0x010) 237 238ENTRY(omap243x_sram_reprogram_sdrc_sz) 239 .word . - omap243x_sram_reprogram_sdrc 240 241/* 242 * Set dividers and pll. Also recalculate DLL value for DDR and unlock mode. 243 */ 244 .align 3 245ENTRY(omap243x_sram_set_prcm) 246 stmfd sp!, {r0-r12, lr} @ regs to stack 247 adr r4, pbegin @ addr of preload start 248 adr r8, pend @ addr of preload end 249 mcrr p15, 1, r8, r4, c12 @ preload into icache 250pbegin: 251 /* move into fast relock bypass */ 252 ldr r8, omap243x_ssp_pll_ctl @ get addr 253 ldr r5, [r8] @ get val 254 mvn r6, #0x3 @ clear mask 255 and r5, r5, r6 @ clear field 256 orr r7, r5, #0x2 @ fast relock val 257 str r7, [r8] @ go to fast relock 258 ldr r4, omap243x_ssp_pll_stat @ addr of stat 259block: 260 /* wait for bypass */ 261 ldr r8, [r4] @ stat value 262 and r8, r8, #0x3 @ mask for stat 263 cmp r8, #0x1 @ there yet 264 bne block @ loop if not 265 266 /* set new dpll dividers _after_ in bypass */ 267 ldr r4, omap243x_ssp_pll_div @ get addr 268 str r0, [r4] @ set dpll ctrl val 269 270 ldr r4, omap243x_ssp_set_config @ get addr 271 mov r8, #1 @ valid cfg msk 272 str r8, [r4] @ make dividers take 273 274 mov r4, #100 @ dead spin a bit 275wait_a_bit: 276 subs r4, r4, #1 @ dec loop 277 bne wait_a_bit @ delay done? 278 279 /* check if staying in bypass */ 280 cmp r2, #0x1 @ stay in bypass? 281 beq pend @ jump over dpll relock 282 283 /* relock DPLL with new vals */ 284 ldr r5, omap243x_ssp_pll_stat @ get addr 285 ldr r4, omap243x_ssp_pll_ctl @ get addr 286 orr r8, r7, #0x3 @ val for lock dpll 287 str r8, [r4] @ set val 288 mov r0, #1000 @ dead spin a bit 289wait_more: 290 subs r0, r0, #1 @ dec loop 291 bne wait_more @ delay done? 292wait_lock: 293 ldr r8, [r5] @ get lock val 294 and r8, r8, #3 @ isolate field 295 cmp r8, #2 @ locked? 296 bne wait_lock @ wait if not 297pend: 298 /* update memory timings & briefly lock dll */ 299 ldr r4, omap243x_ssp_sdrc_rfr @ get addr 300 str r1, [r4] @ update refresh timing 301 ldr r11, omap243x_ssp_dlla_ctrl @ get addr of DLLA ctrl 302 ldr r10, [r11] @ get current val 303 mvn r9, #0x4 @ mask to get clear bit2 304 and r10, r10, r9 @ clear bit2 for lock mode 305 orr r10, r10, #0x8 @ make sure DLL on (es2 bit pos) 306 str r10, [r11] @ commit to DLLA_CTRL 307 add r11, r11, #0x8 @ move to dllb 308 str r10, [r11] @ hit DLLB also 309 310 mov r4, #0x800 @ relock time (min 0x400 L3 clocks) 311wait_dll_lock: 312 subs r4, r4, #0x1 313 bne wait_dll_lock 314 nop 315 ldmfd sp!, {r0-r12, pc} @ restore regs and return 316 317omap243x_ssp_set_config: 318 .word OMAP2430_PRCM_CLKCFG_CTRL 319omap243x_ssp_pll_ctl: 320 .word OMAP2430_CM_REGADDR(PLL_MOD, CM_CLKEN) 321omap243x_ssp_pll_stat: 322 .word OMAP2430_CM_REGADDR(PLL_MOD, CM_IDLEST) 323omap243x_ssp_pll_div: 324 .word OMAP2430_CM_REGADDR(PLL_MOD, CM_CLKSEL1) 325omap243x_ssp_sdrc_rfr: 326 .word OMAP243X_SDRC_REGADDR(SDRC_RFR_CTRL_0) 327omap243x_ssp_dlla_ctrl: 328 .word OMAP243X_SDRC_REGADDR(SDRC_DLLA_CTRL) 329 330ENTRY(omap243x_sram_set_prcm_sz) 331 .word . - omap243x_sram_set_prcm 332