1 /* 2 * OMAP2+ DMA driver 3 * 4 * Copyright (C) 2003 - 2008 Nokia Corporation 5 * Author: Juha Yrjölä <juha.yrjola@nokia.com> 6 * DMA channel linking for 1610 by Samuel Ortiz <samuel.ortiz@nokia.com> 7 * Graphics DMA and LCD DMA graphics tranformations 8 * by Imre Deak <imre.deak@nokia.com> 9 * OMAP2/3 support Copyright (C) 2004-2007 Texas Instruments, Inc. 10 * Some functions based on earlier dma-omap.c Copyright (C) 2001 RidgeRun, Inc. 11 * 12 * Copyright (C) 2009 Texas Instruments 13 * Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com> 14 * 15 * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ 16 * Converted DMA library into platform driver 17 * - G, Manjunath Kondaiah <manjugk@ti.com> 18 * 19 * This program is free software; you can redistribute it and/or modify 20 * it under the terms of the GNU General Public License version 2 as 21 * published by the Free Software Foundation. 22 */ 23 24 #include <linux/err.h> 25 #include <linux/io.h> 26 #include <linux/slab.h> 27 #include <linux/module.h> 28 #include <linux/init.h> 29 #include <linux/device.h> 30 #include <linux/dma-mapping.h> 31 #include <linux/of.h> 32 #include <linux/omap-dma.h> 33 34 #include "soc.h" 35 #include "omap_hwmod.h" 36 #include "omap_device.h" 37 38 static enum omap_reg_offsets dma_common_ch_end; 39 40 static const struct omap_dma_reg reg_map[] = { 41 [REVISION] = { 0x0000, 0x00, OMAP_DMA_REG_32BIT }, 42 [GCR] = { 0x0078, 0x00, OMAP_DMA_REG_32BIT }, 43 [IRQSTATUS_L0] = { 0x0008, 0x00, OMAP_DMA_REG_32BIT }, 44 [IRQSTATUS_L1] = { 0x000c, 0x00, OMAP_DMA_REG_32BIT }, 45 [IRQSTATUS_L2] = { 0x0010, 0x00, OMAP_DMA_REG_32BIT }, 46 [IRQSTATUS_L3] = { 0x0014, 0x00, OMAP_DMA_REG_32BIT }, 47 [IRQENABLE_L0] = { 0x0018, 0x00, OMAP_DMA_REG_32BIT }, 48 [IRQENABLE_L1] = { 0x001c, 0x00, OMAP_DMA_REG_32BIT }, 49 [IRQENABLE_L2] = { 0x0020, 0x00, OMAP_DMA_REG_32BIT }, 50 [IRQENABLE_L3] = { 0x0024, 0x00, OMAP_DMA_REG_32BIT }, 51 [SYSSTATUS] = { 0x0028, 0x00, OMAP_DMA_REG_32BIT }, 52 [OCP_SYSCONFIG] = { 0x002c, 0x00, OMAP_DMA_REG_32BIT }, 53 [CAPS_0] = { 0x0064, 0x00, OMAP_DMA_REG_32BIT }, 54 [CAPS_2] = { 0x006c, 0x00, OMAP_DMA_REG_32BIT }, 55 [CAPS_3] = { 0x0070, 0x00, OMAP_DMA_REG_32BIT }, 56 [CAPS_4] = { 0x0074, 0x00, OMAP_DMA_REG_32BIT }, 57 58 /* Common register offsets */ 59 [CCR] = { 0x0080, 0x60, OMAP_DMA_REG_32BIT }, 60 [CLNK_CTRL] = { 0x0084, 0x60, OMAP_DMA_REG_32BIT }, 61 [CICR] = { 0x0088, 0x60, OMAP_DMA_REG_32BIT }, 62 [CSR] = { 0x008c, 0x60, OMAP_DMA_REG_32BIT }, 63 [CSDP] = { 0x0090, 0x60, OMAP_DMA_REG_32BIT }, 64 [CEN] = { 0x0094, 0x60, OMAP_DMA_REG_32BIT }, 65 [CFN] = { 0x0098, 0x60, OMAP_DMA_REG_32BIT }, 66 [CSEI] = { 0x00a4, 0x60, OMAP_DMA_REG_32BIT }, 67 [CSFI] = { 0x00a8, 0x60, OMAP_DMA_REG_32BIT }, 68 [CDEI] = { 0x00ac, 0x60, OMAP_DMA_REG_32BIT }, 69 [CDFI] = { 0x00b0, 0x60, OMAP_DMA_REG_32BIT }, 70 [CSAC] = { 0x00b4, 0x60, OMAP_DMA_REG_32BIT }, 71 [CDAC] = { 0x00b8, 0x60, OMAP_DMA_REG_32BIT }, 72 73 /* Channel specific register offsets */ 74 [CSSA] = { 0x009c, 0x60, OMAP_DMA_REG_32BIT }, 75 [CDSA] = { 0x00a0, 0x60, OMAP_DMA_REG_32BIT }, 76 [CCEN] = { 0x00bc, 0x60, OMAP_DMA_REG_32BIT }, 77 [CCFN] = { 0x00c0, 0x60, OMAP_DMA_REG_32BIT }, 78 [COLOR] = { 0x00c4, 0x60, OMAP_DMA_REG_32BIT }, 79 80 /* OMAP4 specific registers */ 81 [CDP] = { 0x00d0, 0x60, OMAP_DMA_REG_32BIT }, 82 [CNDP] = { 0x00d4, 0x60, OMAP_DMA_REG_32BIT }, 83 [CCDN] = { 0x00d8, 0x60, OMAP_DMA_REG_32BIT }, 84 }; 85 86 static void __iomem *dma_base; 87 static inline void dma_write(u32 val, int reg, int lch) 88 { 89 void __iomem *addr = dma_base; 90 91 addr += reg_map[reg].offset; 92 addr += reg_map[reg].stride * lch; 93 94 writel_relaxed(val, addr); 95 } 96 97 static inline u32 dma_read(int reg, int lch) 98 { 99 void __iomem *addr = dma_base; 100 101 addr += reg_map[reg].offset; 102 addr += reg_map[reg].stride * lch; 103 104 return readl_relaxed(addr); 105 } 106 107 static void omap2_clear_dma(int lch) 108 { 109 int i; 110 111 for (i = CSDP; i <= dma_common_ch_end; i += 1) 112 dma_write(0, i, lch); 113 } 114 115 static void omap2_show_dma_caps(void) 116 { 117 u8 revision = dma_read(REVISION, 0) & 0xff; 118 printk(KERN_INFO "OMAP DMA hardware revision %d.%d\n", 119 revision >> 4, revision & 0xf); 120 return; 121 } 122 123 static unsigned configure_dma_errata(void) 124 { 125 unsigned errata = 0; 126 127 /* 128 * Errata applicable for OMAP2430ES1.0 and all omap2420 129 * 130 * I. 131 * Erratum ID: Not Available 132 * Inter Frame DMA buffering issue DMA will wrongly 133 * buffer elements if packing and bursting is enabled. This might 134 * result in data gets stalled in FIFO at the end of the block. 135 * Workaround: DMA channels must have BUFFERING_DISABLED bit set to 136 * guarantee no data will stay in the DMA FIFO in case inter frame 137 * buffering occurs 138 * 139 * II. 140 * Erratum ID: Not Available 141 * DMA may hang when several channels are used in parallel 142 * In the following configuration, DMA channel hanging can occur: 143 * a. Channel i, hardware synchronized, is enabled 144 * b. Another channel (Channel x), software synchronized, is enabled. 145 * c. Channel i is disabled before end of transfer 146 * d. Channel i is reenabled. 147 * e. Steps 1 to 4 are repeated a certain number of times. 148 * f. A third channel (Channel y), software synchronized, is enabled. 149 * Channel x and Channel y may hang immediately after step 'f'. 150 * Workaround: 151 * For any channel used - make sure NextLCH_ID is set to the value j. 152 */ 153 if (cpu_is_omap2420() || (cpu_is_omap2430() && 154 (omap_type() == OMAP2430_REV_ES1_0))) { 155 156 SET_DMA_ERRATA(DMA_ERRATA_IFRAME_BUFFERING); 157 SET_DMA_ERRATA(DMA_ERRATA_PARALLEL_CHANNELS); 158 } 159 160 /* 161 * Erratum ID: i378: OMAP2+: sDMA Channel is not disabled 162 * after a transaction error. 163 * Workaround: SW should explicitely disable the channel. 164 */ 165 if (cpu_class_is_omap2()) 166 SET_DMA_ERRATA(DMA_ERRATA_i378); 167 168 /* 169 * Erratum ID: i541: sDMA FIFO draining does not finish 170 * If sDMA channel is disabled on the fly, sDMA enters standby even 171 * through FIFO Drain is still in progress 172 * Workaround: Put sDMA in NoStandby more before a logical channel is 173 * disabled, then put it back to SmartStandby right after the channel 174 * finishes FIFO draining. 175 */ 176 if (cpu_is_omap34xx()) 177 SET_DMA_ERRATA(DMA_ERRATA_i541); 178 179 /* 180 * Erratum ID: i88 : Special programming model needed to disable DMA 181 * before end of block. 182 * Workaround: software must ensure that the DMA is configured in No 183 * Standby mode(DMAx_OCP_SYSCONFIG.MIDLEMODE = "01") 184 */ 185 if (omap_type() == OMAP3430_REV_ES1_0) 186 SET_DMA_ERRATA(DMA_ERRATA_i88); 187 188 /* 189 * Erratum 3.2/3.3: sometimes 0 is returned if CSAC/CDAC is 190 * read before the DMA controller finished disabling the channel. 191 */ 192 SET_DMA_ERRATA(DMA_ERRATA_3_3); 193 194 /* 195 * Erratum ID: Not Available 196 * A bug in ROM code leaves IRQ status for channels 0 and 1 uncleared 197 * after secure sram context save and restore. 198 * Work around: Hence we need to manually clear those IRQs to avoid 199 * spurious interrupts. This affects only secure devices. 200 */ 201 if (cpu_is_omap34xx() && (omap_type() != OMAP2_DEVICE_TYPE_GP)) 202 SET_DMA_ERRATA(DMA_ROMCODE_BUG); 203 204 return errata; 205 } 206 207 static struct omap_system_dma_plat_info dma_plat_info __initdata = { 208 .reg_map = reg_map, 209 .channel_stride = 0x60, 210 .show_dma_caps = omap2_show_dma_caps, 211 .clear_dma = omap2_clear_dma, 212 .dma_write = dma_write, 213 .dma_read = dma_read, 214 }; 215 216 static struct platform_device_info omap_dma_dev_info = { 217 .name = "omap-dma-engine", 218 .id = -1, 219 .dma_mask = DMA_BIT_MASK(32), 220 }; 221 222 /* One time initializations */ 223 static int __init omap2_system_dma_init_dev(struct omap_hwmod *oh, void *unused) 224 { 225 struct platform_device *pdev; 226 struct omap_system_dma_plat_info p; 227 struct omap_dma_dev_attr *d; 228 struct resource *mem; 229 char *name = "omap_dma_system"; 230 231 p = dma_plat_info; 232 p.dma_attr = (struct omap_dma_dev_attr *)oh->dev_attr; 233 p.errata = configure_dma_errata(); 234 235 pdev = omap_device_build(name, 0, oh, &p, sizeof(p)); 236 if (IS_ERR(pdev)) { 237 pr_err("%s: Can't build omap_device for %s:%s.\n", 238 __func__, name, oh->name); 239 return PTR_ERR(pdev); 240 } 241 242 omap_dma_dev_info.res = pdev->resource; 243 omap_dma_dev_info.num_res = pdev->num_resources; 244 245 mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); 246 if (!mem) { 247 dev_err(&pdev->dev, "%s: no mem resource\n", __func__); 248 return -EINVAL; 249 } 250 251 dma_base = ioremap(mem->start, resource_size(mem)); 252 if (!dma_base) { 253 dev_err(&pdev->dev, "%s: ioremap fail\n", __func__); 254 return -ENOMEM; 255 } 256 257 d = oh->dev_attr; 258 259 if (cpu_is_omap34xx() && (omap_type() != OMAP2_DEVICE_TYPE_GP)) 260 d->dev_caps |= HS_CHANNELS_RESERVED; 261 262 /* Check the capabilities register for descriptor loading feature */ 263 if (dma_read(CAPS_0, 0) & DMA_HAS_DESCRIPTOR_CAPS) 264 dma_common_ch_end = CCDN; 265 else 266 dma_common_ch_end = CCFN; 267 268 return 0; 269 } 270 271 static int __init omap2_system_dma_init(void) 272 { 273 struct platform_device *pdev; 274 int res; 275 276 res = omap_hwmod_for_each_by_class("dma", 277 omap2_system_dma_init_dev, NULL); 278 if (res) 279 return res; 280 281 if (of_have_populated_dt()) 282 return res; 283 284 pdev = platform_device_register_full(&omap_dma_dev_info); 285 if (IS_ERR(pdev)) 286 return PTR_ERR(pdev); 287 288 return res; 289 } 290 omap_arch_initcall(omap2_system_dma_init); 291