1 /* 2 * OMAP2+ DMA driver 3 * 4 * Copyright (C) 2003 - 2008 Nokia Corporation 5 * Author: Juha Yrjölä <juha.yrjola@nokia.com> 6 * DMA channel linking for 1610 by Samuel Ortiz <samuel.ortiz@nokia.com> 7 * Graphics DMA and LCD DMA graphics tranformations 8 * by Imre Deak <imre.deak@nokia.com> 9 * OMAP2/3 support Copyright (C) 2004-2007 Texas Instruments, Inc. 10 * Some functions based on earlier dma-omap.c Copyright (C) 2001 RidgeRun, Inc. 11 * 12 * Copyright (C) 2009 Texas Instruments 13 * Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com> 14 * 15 * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ 16 * Converted DMA library into platform driver 17 * - G, Manjunath Kondaiah <manjugk@ti.com> 18 * 19 * This program is free software; you can redistribute it and/or modify 20 * it under the terms of the GNU General Public License version 2 as 21 * published by the Free Software Foundation. 22 */ 23 24 #include <linux/err.h> 25 #include <linux/io.h> 26 #include <linux/slab.h> 27 #include <linux/module.h> 28 #include <linux/init.h> 29 #include <linux/device.h> 30 31 #include <plat/omap_hwmod.h> 32 #include <plat/omap_device.h> 33 #include <plat/dma.h> 34 35 #define OMAP2_DMA_STRIDE 0x60 36 37 static u32 errata; 38 static u8 dma_stride; 39 40 static struct omap_dma_dev_attr *d; 41 42 static enum omap_reg_offsets dma_common_ch_start, dma_common_ch_end; 43 44 static u16 reg_map[] = { 45 [REVISION] = 0x00, 46 [GCR] = 0x78, 47 [IRQSTATUS_L0] = 0x08, 48 [IRQSTATUS_L1] = 0x0c, 49 [IRQSTATUS_L2] = 0x10, 50 [IRQSTATUS_L3] = 0x14, 51 [IRQENABLE_L0] = 0x18, 52 [IRQENABLE_L1] = 0x1c, 53 [IRQENABLE_L2] = 0x20, 54 [IRQENABLE_L3] = 0x24, 55 [SYSSTATUS] = 0x28, 56 [OCP_SYSCONFIG] = 0x2c, 57 [CAPS_0] = 0x64, 58 [CAPS_2] = 0x6c, 59 [CAPS_3] = 0x70, 60 [CAPS_4] = 0x74, 61 62 /* Common register offsets */ 63 [CCR] = 0x80, 64 [CLNK_CTRL] = 0x84, 65 [CICR] = 0x88, 66 [CSR] = 0x8c, 67 [CSDP] = 0x90, 68 [CEN] = 0x94, 69 [CFN] = 0x98, 70 [CSEI] = 0xa4, 71 [CSFI] = 0xa8, 72 [CDEI] = 0xac, 73 [CDFI] = 0xb0, 74 [CSAC] = 0xb4, 75 [CDAC] = 0xb8, 76 77 /* Channel specific register offsets */ 78 [CSSA] = 0x9c, 79 [CDSA] = 0xa0, 80 [CCEN] = 0xbc, 81 [CCFN] = 0xc0, 82 [COLOR] = 0xc4, 83 84 /* OMAP4 specific registers */ 85 [CDP] = 0xd0, 86 [CNDP] = 0xd4, 87 [CCDN] = 0xd8, 88 }; 89 90 static void __iomem *dma_base; 91 static inline void dma_write(u32 val, int reg, int lch) 92 { 93 u8 stride; 94 u32 offset; 95 96 stride = (reg >= dma_common_ch_start) ? dma_stride : 0; 97 offset = reg_map[reg] + (stride * lch); 98 __raw_writel(val, dma_base + offset); 99 } 100 101 static inline u32 dma_read(int reg, int lch) 102 { 103 u8 stride; 104 u32 offset, val; 105 106 stride = (reg >= dma_common_ch_start) ? dma_stride : 0; 107 offset = reg_map[reg] + (stride * lch); 108 val = __raw_readl(dma_base + offset); 109 return val; 110 } 111 112 static inline void omap2_disable_irq_lch(int lch) 113 { 114 u32 val; 115 116 val = dma_read(IRQENABLE_L0, lch); 117 val &= ~(1 << lch); 118 dma_write(val, IRQENABLE_L0, lch); 119 } 120 121 static void omap2_clear_dma(int lch) 122 { 123 int i = dma_common_ch_start; 124 125 for (; i <= dma_common_ch_end; i += 1) 126 dma_write(0, i, lch); 127 } 128 129 static void omap2_show_dma_caps(void) 130 { 131 u8 revision = dma_read(REVISION, 0) & 0xff; 132 printk(KERN_INFO "OMAP DMA hardware revision %d.%d\n", 133 revision >> 4, revision & 0xf); 134 return; 135 } 136 137 static u32 configure_dma_errata(void) 138 { 139 140 /* 141 * Errata applicable for OMAP2430ES1.0 and all omap2420 142 * 143 * I. 144 * Erratum ID: Not Available 145 * Inter Frame DMA buffering issue DMA will wrongly 146 * buffer elements if packing and bursting is enabled. This might 147 * result in data gets stalled in FIFO at the end of the block. 148 * Workaround: DMA channels must have BUFFERING_DISABLED bit set to 149 * guarantee no data will stay in the DMA FIFO in case inter frame 150 * buffering occurs 151 * 152 * II. 153 * Erratum ID: Not Available 154 * DMA may hang when several channels are used in parallel 155 * In the following configuration, DMA channel hanging can occur: 156 * a. Channel i, hardware synchronized, is enabled 157 * b. Another channel (Channel x), software synchronized, is enabled. 158 * c. Channel i is disabled before end of transfer 159 * d. Channel i is reenabled. 160 * e. Steps 1 to 4 are repeated a certain number of times. 161 * f. A third channel (Channel y), software synchronized, is enabled. 162 * Channel x and Channel y may hang immediately after step 'f'. 163 * Workaround: 164 * For any channel used - make sure NextLCH_ID is set to the value j. 165 */ 166 if (cpu_is_omap2420() || (cpu_is_omap2430() && 167 (omap_type() == OMAP2430_REV_ES1_0))) { 168 169 SET_DMA_ERRATA(DMA_ERRATA_IFRAME_BUFFERING); 170 SET_DMA_ERRATA(DMA_ERRATA_PARALLEL_CHANNELS); 171 } 172 173 /* 174 * Erratum ID: i378: OMAP2+: sDMA Channel is not disabled 175 * after a transaction error. 176 * Workaround: SW should explicitely disable the channel. 177 */ 178 if (cpu_class_is_omap2()) 179 SET_DMA_ERRATA(DMA_ERRATA_i378); 180 181 /* 182 * Erratum ID: i541: sDMA FIFO draining does not finish 183 * If sDMA channel is disabled on the fly, sDMA enters standby even 184 * through FIFO Drain is still in progress 185 * Workaround: Put sDMA in NoStandby more before a logical channel is 186 * disabled, then put it back to SmartStandby right after the channel 187 * finishes FIFO draining. 188 */ 189 if (cpu_is_omap34xx()) 190 SET_DMA_ERRATA(DMA_ERRATA_i541); 191 192 /* 193 * Erratum ID: i88 : Special programming model needed to disable DMA 194 * before end of block. 195 * Workaround: software must ensure that the DMA is configured in No 196 * Standby mode(DMAx_OCP_SYSCONFIG.MIDLEMODE = "01") 197 */ 198 if (omap_type() == OMAP3430_REV_ES1_0) 199 SET_DMA_ERRATA(DMA_ERRATA_i88); 200 201 /* 202 * Erratum 3.2/3.3: sometimes 0 is returned if CSAC/CDAC is 203 * read before the DMA controller finished disabling the channel. 204 */ 205 SET_DMA_ERRATA(DMA_ERRATA_3_3); 206 207 /* 208 * Erratum ID: Not Available 209 * A bug in ROM code leaves IRQ status for channels 0 and 1 uncleared 210 * after secure sram context save and restore. 211 * Work around: Hence we need to manually clear those IRQs to avoid 212 * spurious interrupts. This affects only secure devices. 213 */ 214 if (cpu_is_omap34xx() && (omap_type() != OMAP2_DEVICE_TYPE_GP)) 215 SET_DMA_ERRATA(DMA_ROMCODE_BUG); 216 217 return errata; 218 } 219 220 /* One time initializations */ 221 static int __init omap2_system_dma_init_dev(struct omap_hwmod *oh, void *unused) 222 { 223 struct platform_device *pdev; 224 struct omap_system_dma_plat_info *p; 225 struct resource *mem; 226 char *name = "omap_dma_system"; 227 228 dma_stride = OMAP2_DMA_STRIDE; 229 dma_common_ch_start = CSDP; 230 231 p = kzalloc(sizeof(struct omap_system_dma_plat_info), GFP_KERNEL); 232 if (!p) { 233 pr_err("%s: Unable to allocate pdata for %s:%s\n", 234 __func__, name, oh->name); 235 return -ENOMEM; 236 } 237 238 p->dma_attr = (struct omap_dma_dev_attr *)oh->dev_attr; 239 p->disable_irq_lch = omap2_disable_irq_lch; 240 p->show_dma_caps = omap2_show_dma_caps; 241 p->clear_dma = omap2_clear_dma; 242 p->dma_write = dma_write; 243 p->dma_read = dma_read; 244 245 p->clear_lch_regs = NULL; 246 247 p->errata = configure_dma_errata(); 248 249 pdev = omap_device_build(name, 0, oh, p, sizeof(*p), NULL, 0, 0); 250 kfree(p); 251 if (IS_ERR(pdev)) { 252 pr_err("%s: Can't build omap_device for %s:%s.\n", 253 __func__, name, oh->name); 254 return PTR_ERR(pdev); 255 } 256 257 mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); 258 if (!mem) { 259 dev_err(&pdev->dev, "%s: no mem resource\n", __func__); 260 return -EINVAL; 261 } 262 dma_base = ioremap(mem->start, resource_size(mem)); 263 if (!dma_base) { 264 dev_err(&pdev->dev, "%s: ioremap fail\n", __func__); 265 return -ENOMEM; 266 } 267 268 d = oh->dev_attr; 269 d->chan = kzalloc(sizeof(struct omap_dma_lch) * 270 (d->lch_count), GFP_KERNEL); 271 272 if (!d->chan) { 273 dev_err(&pdev->dev, "%s: kzalloc fail\n", __func__); 274 return -ENOMEM; 275 } 276 277 /* Check the capabilities register for descriptor loading feature */ 278 if (dma_read(CAPS_0, 0) & DMA_HAS_DESCRIPTOR_CAPS) 279 dma_common_ch_end = CCDN; 280 else 281 dma_common_ch_end = CCFN; 282 283 return 0; 284 } 285 286 static int __init omap2_system_dma_init(void) 287 { 288 return omap_hwmod_for_each_by_class("dma", 289 omap2_system_dma_init_dev, NULL); 290 } 291 arch_initcall(omap2_system_dma_init); 292