1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * OMAP2+ DMA driver 4 * 5 * Copyright (C) 2003 - 2008 Nokia Corporation 6 * Author: Juha Yrjölä <juha.yrjola@nokia.com> 7 * DMA channel linking for 1610 by Samuel Ortiz <samuel.ortiz@nokia.com> 8 * Graphics DMA and LCD DMA graphics tranformations 9 * by Imre Deak <imre.deak@nokia.com> 10 * OMAP2/3 support Copyright (C) 2004-2007 Texas Instruments, Inc. 11 * Some functions based on earlier dma-omap.c Copyright (C) 2001 RidgeRun, Inc. 12 * 13 * Copyright (C) 2009 Texas Instruments 14 * Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com> 15 * 16 * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ 17 * Converted DMA library into platform driver 18 * - G, Manjunath Kondaiah <manjugk@ti.com> 19 */ 20 21 #include <linux/err.h> 22 #include <linux/io.h> 23 #include <linux/slab.h> 24 #include <linux/module.h> 25 #include <linux/init.h> 26 #include <linux/device.h> 27 #include <linux/dma-mapping.h> 28 #include <linux/dmaengine.h> 29 #include <linux/of.h> 30 #include <linux/omap-dma.h> 31 32 #include "soc.h" 33 #include "omap_hwmod.h" 34 #include "omap_device.h" 35 36 static enum omap_reg_offsets dma_common_ch_end; 37 38 static const struct omap_dma_reg reg_map[] = { 39 [REVISION] = { 0x0000, 0x00, OMAP_DMA_REG_32BIT }, 40 [GCR] = { 0x0078, 0x00, OMAP_DMA_REG_32BIT }, 41 [IRQSTATUS_L0] = { 0x0008, 0x00, OMAP_DMA_REG_32BIT }, 42 [IRQSTATUS_L1] = { 0x000c, 0x00, OMAP_DMA_REG_32BIT }, 43 [IRQSTATUS_L2] = { 0x0010, 0x00, OMAP_DMA_REG_32BIT }, 44 [IRQSTATUS_L3] = { 0x0014, 0x00, OMAP_DMA_REG_32BIT }, 45 [IRQENABLE_L0] = { 0x0018, 0x00, OMAP_DMA_REG_32BIT }, 46 [IRQENABLE_L1] = { 0x001c, 0x00, OMAP_DMA_REG_32BIT }, 47 [IRQENABLE_L2] = { 0x0020, 0x00, OMAP_DMA_REG_32BIT }, 48 [IRQENABLE_L3] = { 0x0024, 0x00, OMAP_DMA_REG_32BIT }, 49 [SYSSTATUS] = { 0x0028, 0x00, OMAP_DMA_REG_32BIT }, 50 [OCP_SYSCONFIG] = { 0x002c, 0x00, OMAP_DMA_REG_32BIT }, 51 [CAPS_0] = { 0x0064, 0x00, OMAP_DMA_REG_32BIT }, 52 [CAPS_2] = { 0x006c, 0x00, OMAP_DMA_REG_32BIT }, 53 [CAPS_3] = { 0x0070, 0x00, OMAP_DMA_REG_32BIT }, 54 [CAPS_4] = { 0x0074, 0x00, OMAP_DMA_REG_32BIT }, 55 56 /* Common register offsets */ 57 [CCR] = { 0x0080, 0x60, OMAP_DMA_REG_32BIT }, 58 [CLNK_CTRL] = { 0x0084, 0x60, OMAP_DMA_REG_32BIT }, 59 [CICR] = { 0x0088, 0x60, OMAP_DMA_REG_32BIT }, 60 [CSR] = { 0x008c, 0x60, OMAP_DMA_REG_32BIT }, 61 [CSDP] = { 0x0090, 0x60, OMAP_DMA_REG_32BIT }, 62 [CEN] = { 0x0094, 0x60, OMAP_DMA_REG_32BIT }, 63 [CFN] = { 0x0098, 0x60, OMAP_DMA_REG_32BIT }, 64 [CSEI] = { 0x00a4, 0x60, OMAP_DMA_REG_32BIT }, 65 [CSFI] = { 0x00a8, 0x60, OMAP_DMA_REG_32BIT }, 66 [CDEI] = { 0x00ac, 0x60, OMAP_DMA_REG_32BIT }, 67 [CDFI] = { 0x00b0, 0x60, OMAP_DMA_REG_32BIT }, 68 [CSAC] = { 0x00b4, 0x60, OMAP_DMA_REG_32BIT }, 69 [CDAC] = { 0x00b8, 0x60, OMAP_DMA_REG_32BIT }, 70 71 /* Channel specific register offsets */ 72 [CSSA] = { 0x009c, 0x60, OMAP_DMA_REG_32BIT }, 73 [CDSA] = { 0x00a0, 0x60, OMAP_DMA_REG_32BIT }, 74 [CCEN] = { 0x00bc, 0x60, OMAP_DMA_REG_32BIT }, 75 [CCFN] = { 0x00c0, 0x60, OMAP_DMA_REG_32BIT }, 76 [COLOR] = { 0x00c4, 0x60, OMAP_DMA_REG_32BIT }, 77 78 /* OMAP4 specific registers */ 79 [CDP] = { 0x00d0, 0x60, OMAP_DMA_REG_32BIT }, 80 [CNDP] = { 0x00d4, 0x60, OMAP_DMA_REG_32BIT }, 81 [CCDN] = { 0x00d8, 0x60, OMAP_DMA_REG_32BIT }, 82 }; 83 84 static void __iomem *dma_base; 85 static inline void dma_write(u32 val, int reg, int lch) 86 { 87 void __iomem *addr = dma_base; 88 89 addr += reg_map[reg].offset; 90 addr += reg_map[reg].stride * lch; 91 92 writel_relaxed(val, addr); 93 } 94 95 static inline u32 dma_read(int reg, int lch) 96 { 97 void __iomem *addr = dma_base; 98 99 addr += reg_map[reg].offset; 100 addr += reg_map[reg].stride * lch; 101 102 return readl_relaxed(addr); 103 } 104 105 static void omap2_clear_dma(int lch) 106 { 107 int i; 108 109 for (i = CSDP; i <= dma_common_ch_end; i += 1) 110 dma_write(0, i, lch); 111 } 112 113 static void omap2_show_dma_caps(void) 114 { 115 u8 revision = dma_read(REVISION, 0) & 0xff; 116 printk(KERN_INFO "OMAP DMA hardware revision %d.%d\n", 117 revision >> 4, revision & 0xf); 118 } 119 120 static unsigned configure_dma_errata(void) 121 { 122 unsigned errata = 0; 123 124 /* 125 * Errata applicable for OMAP2430ES1.0 and all omap2420 126 * 127 * I. 128 * Erratum ID: Not Available 129 * Inter Frame DMA buffering issue DMA will wrongly 130 * buffer elements if packing and bursting is enabled. This might 131 * result in data gets stalled in FIFO at the end of the block. 132 * Workaround: DMA channels must have BUFFERING_DISABLED bit set to 133 * guarantee no data will stay in the DMA FIFO in case inter frame 134 * buffering occurs 135 * 136 * II. 137 * Erratum ID: Not Available 138 * DMA may hang when several channels are used in parallel 139 * In the following configuration, DMA channel hanging can occur: 140 * a. Channel i, hardware synchronized, is enabled 141 * b. Another channel (Channel x), software synchronized, is enabled. 142 * c. Channel i is disabled before end of transfer 143 * d. Channel i is reenabled. 144 * e. Steps 1 to 4 are repeated a certain number of times. 145 * f. A third channel (Channel y), software synchronized, is enabled. 146 * Channel x and Channel y may hang immediately after step 'f'. 147 * Workaround: 148 * For any channel used - make sure NextLCH_ID is set to the value j. 149 */ 150 if (cpu_is_omap2420() || (cpu_is_omap2430() && 151 (omap_type() == OMAP2430_REV_ES1_0))) { 152 153 SET_DMA_ERRATA(DMA_ERRATA_IFRAME_BUFFERING); 154 SET_DMA_ERRATA(DMA_ERRATA_PARALLEL_CHANNELS); 155 } 156 157 /* 158 * Erratum ID: i378: OMAP2+: sDMA Channel is not disabled 159 * after a transaction error. 160 * Workaround: SW should explicitely disable the channel. 161 */ 162 if (cpu_class_is_omap2()) 163 SET_DMA_ERRATA(DMA_ERRATA_i378); 164 165 /* 166 * Erratum ID: i541: sDMA FIFO draining does not finish 167 * If sDMA channel is disabled on the fly, sDMA enters standby even 168 * through FIFO Drain is still in progress 169 * Workaround: Put sDMA in NoStandby more before a logical channel is 170 * disabled, then put it back to SmartStandby right after the channel 171 * finishes FIFO draining. 172 */ 173 if (cpu_is_omap34xx()) 174 SET_DMA_ERRATA(DMA_ERRATA_i541); 175 176 /* 177 * Erratum ID: i88 : Special programming model needed to disable DMA 178 * before end of block. 179 * Workaround: software must ensure that the DMA is configured in No 180 * Standby mode(DMAx_OCP_SYSCONFIG.MIDLEMODE = "01") 181 */ 182 if (omap_type() == OMAP3430_REV_ES1_0) 183 SET_DMA_ERRATA(DMA_ERRATA_i88); 184 185 /* 186 * Erratum 3.2/3.3: sometimes 0 is returned if CSAC/CDAC is 187 * read before the DMA controller finished disabling the channel. 188 */ 189 SET_DMA_ERRATA(DMA_ERRATA_3_3); 190 191 /* 192 * Erratum ID: Not Available 193 * A bug in ROM code leaves IRQ status for channels 0 and 1 uncleared 194 * after secure sram context save and restore. 195 * Work around: Hence we need to manually clear those IRQs to avoid 196 * spurious interrupts. This affects only secure devices. 197 */ 198 if (cpu_is_omap34xx() && (omap_type() != OMAP2_DEVICE_TYPE_GP)) 199 SET_DMA_ERRATA(DMA_ROMCODE_BUG); 200 201 return errata; 202 } 203 204 static const struct dma_slave_map omap24xx_sdma_dt_map[] = { 205 /* external DMA requests when tusb6010 is used */ 206 { "musb-hdrc.1.auto", "dmareq0", SDMA_FILTER_PARAM(2) }, 207 { "musb-hdrc.1.auto", "dmareq1", SDMA_FILTER_PARAM(3) }, 208 { "musb-hdrc.1.auto", "dmareq2", SDMA_FILTER_PARAM(14) }, /* OMAP2420 only */ 209 { "musb-hdrc.1.auto", "dmareq3", SDMA_FILTER_PARAM(15) }, /* OMAP2420 only */ 210 { "musb-hdrc.1.auto", "dmareq4", SDMA_FILTER_PARAM(16) }, /* OMAP2420 only */ 211 { "musb-hdrc.1.auto", "dmareq5", SDMA_FILTER_PARAM(64) }, /* OMAP2420 only */ 212 }; 213 214 static struct omap_system_dma_plat_info dma_plat_info __initdata = { 215 .reg_map = reg_map, 216 .channel_stride = 0x60, 217 .show_dma_caps = omap2_show_dma_caps, 218 .clear_dma = omap2_clear_dma, 219 .dma_write = dma_write, 220 .dma_read = dma_read, 221 }; 222 223 static struct platform_device_info omap_dma_dev_info __initdata = { 224 .name = "omap-dma-engine", 225 .id = -1, 226 .dma_mask = DMA_BIT_MASK(32), 227 }; 228 229 /* One time initializations */ 230 static int __init omap2_system_dma_init_dev(struct omap_hwmod *oh, void *unused) 231 { 232 struct platform_device *pdev; 233 struct omap_system_dma_plat_info p; 234 struct omap_dma_dev_attr *d; 235 struct resource *mem; 236 char *name = "omap_dma_system"; 237 238 p = dma_plat_info; 239 p.dma_attr = (struct omap_dma_dev_attr *)oh->dev_attr; 240 p.errata = configure_dma_errata(); 241 242 if (soc_is_omap24xx()) { 243 /* DMA slave map for drivers not yet converted to DT */ 244 p.slave_map = omap24xx_sdma_dt_map; 245 p.slavecnt = ARRAY_SIZE(omap24xx_sdma_dt_map); 246 } 247 248 pdev = omap_device_build(name, 0, oh, &p, sizeof(p)); 249 if (IS_ERR(pdev)) { 250 pr_err("%s: Can't build omap_device for %s:%s.\n", 251 __func__, name, oh->name); 252 return PTR_ERR(pdev); 253 } 254 255 omap_dma_dev_info.res = pdev->resource; 256 omap_dma_dev_info.num_res = pdev->num_resources; 257 258 mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); 259 if (!mem) { 260 dev_err(&pdev->dev, "%s: no mem resource\n", __func__); 261 return -EINVAL; 262 } 263 264 dma_base = ioremap(mem->start, resource_size(mem)); 265 if (!dma_base) { 266 dev_err(&pdev->dev, "%s: ioremap fail\n", __func__); 267 return -ENOMEM; 268 } 269 270 d = oh->dev_attr; 271 272 if (cpu_is_omap34xx() && (omap_type() != OMAP2_DEVICE_TYPE_GP)) 273 d->dev_caps |= HS_CHANNELS_RESERVED; 274 275 if (platform_get_irq_byname(pdev, "0") < 0) 276 d->dev_caps |= DMA_ENGINE_HANDLE_IRQ; 277 278 /* Check the capabilities register for descriptor loading feature */ 279 if (dma_read(CAPS_0, 0) & DMA_HAS_DESCRIPTOR_CAPS) 280 dma_common_ch_end = CCDN; 281 else 282 dma_common_ch_end = CCFN; 283 284 return 0; 285 } 286 287 static int __init omap2_system_dma_init(void) 288 { 289 return omap_hwmod_for_each_by_class("dma", 290 omap2_system_dma_init_dev, NULL); 291 } 292 omap_arch_initcall(omap2_system_dma_init); 293