1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * OMAP2xxx DVFS virtual clock functions 4 * 5 * Copyright (C) 2005-2008, 2012 Texas Instruments, Inc. 6 * Copyright (C) 2004-2010 Nokia Corporation 7 * 8 * Contacts: 9 * Richard Woodruff <r-woodruff2@ti.com> 10 * Paul Walmsley 11 * 12 * Based on earlier work by Tuukka Tikkanen, Tony Lindgren, 13 * Gordon McNutt and RidgeRun, Inc. 14 * 15 * XXX Some of this code should be replaceable by the upcoming OPP layer 16 * code. However, some notion of "rate set" is probably still necessary 17 * for OMAP2xxx at least. Rate sets should be generalized so they can be 18 * used for any OMAP chip, not just OMAP2xxx. In particular, Richard Woodruff 19 * has in the past expressed a preference to use rate sets for OPP changes, 20 * rather than dynamically recalculating the clock tree, so if someone wants 21 * this badly enough to write the code to handle it, we should support it 22 * as an option. 23 */ 24 #undef DEBUG 25 26 #include <linux/kernel.h> 27 #include <linux/errno.h> 28 #include <linux/clk.h> 29 #include <linux/io.h> 30 #include <linux/cpufreq.h> 31 #include <linux/slab.h> 32 33 #include "soc.h" 34 #include "clock.h" 35 #include "clock2xxx.h" 36 #include "opp2xxx.h" 37 #include "cm2xxx.h" 38 #include "cm-regbits-24xx.h" 39 #include "sdrc.h" 40 #include "sram.h" 41 42 const struct prcm_config *curr_prcm_set; 43 const struct prcm_config *rate_table; 44 45 /* 46 * sys_ck_rate: the rate of the external high-frequency clock 47 * oscillator on the board. Set by the SoC-specific clock init code. 48 * Once set during a boot, will not change. 49 */ 50 static unsigned long sys_ck_rate; 51 52 /** 53 * omap2_table_mpu_recalc - just return the MPU speed 54 * @clk: virt_prcm_set struct clk 55 * 56 * Set virt_prcm_set's rate to the mpu_speed field of the current PRCM set. 57 */ 58 unsigned long omap2_table_mpu_recalc(struct clk_hw *clk, 59 unsigned long parent_rate) 60 { 61 return curr_prcm_set->mpu_speed; 62 } 63 64 /* 65 * Look for a rate equal or less than the target rate given a configuration set. 66 * 67 * What's not entirely clear is "which" field represents the key field. 68 * Some might argue L3-DDR, others ARM, others IVA. This code is simple and 69 * just uses the ARM rates. 70 */ 71 long omap2_round_to_table_rate(struct clk_hw *hw, unsigned long rate, 72 unsigned long *parent_rate) 73 { 74 const struct prcm_config *ptr; 75 long highest_rate; 76 77 highest_rate = -EINVAL; 78 79 for (ptr = rate_table; ptr->mpu_speed; ptr++) { 80 if (!(ptr->flags & cpu_mask)) 81 continue; 82 if (ptr->xtal_speed != sys_ck_rate) 83 continue; 84 85 highest_rate = ptr->mpu_speed; 86 87 /* Can check only after xtal frequency check */ 88 if (ptr->mpu_speed <= rate) 89 break; 90 } 91 return highest_rate; 92 } 93 94 /* Sets basic clocks based on the specified rate */ 95 int omap2_select_table_rate(struct clk_hw *hw, unsigned long rate, 96 unsigned long parent_rate) 97 { 98 u32 cur_rate, done_rate, bypass = 0; 99 const struct prcm_config *prcm; 100 unsigned long found_speed = 0; 101 unsigned long flags; 102 103 for (prcm = rate_table; prcm->mpu_speed; prcm++) { 104 if (!(prcm->flags & cpu_mask)) 105 continue; 106 107 if (prcm->xtal_speed != sys_ck_rate) 108 continue; 109 110 if (prcm->mpu_speed <= rate) { 111 found_speed = prcm->mpu_speed; 112 break; 113 } 114 } 115 116 if (!found_speed) { 117 printk(KERN_INFO "Could not set MPU rate to %luMHz\n", 118 rate / 1000000); 119 return -EINVAL; 120 } 121 122 curr_prcm_set = prcm; 123 cur_rate = omap2xxx_clk_get_core_rate(); 124 125 if (prcm->dpll_speed == cur_rate / 2) { 126 omap2xxx_sdrc_reprogram(CORE_CLK_SRC_DPLL, 1); 127 } else if (prcm->dpll_speed == cur_rate * 2) { 128 omap2xxx_sdrc_reprogram(CORE_CLK_SRC_DPLL_X2, 1); 129 } else if (prcm->dpll_speed != cur_rate) { 130 local_irq_save(flags); 131 132 if (prcm->dpll_speed == prcm->xtal_speed) 133 bypass = 1; 134 135 if ((prcm->cm_clksel2_pll & OMAP24XX_CORE_CLK_SRC_MASK) == 136 CORE_CLK_SRC_DPLL_X2) 137 done_rate = CORE_CLK_SRC_DPLL_X2; 138 else 139 done_rate = CORE_CLK_SRC_DPLL; 140 141 omap2xxx_cm_set_mod_dividers(prcm->cm_clksel_mpu, 142 prcm->cm_clksel_dsp, 143 prcm->cm_clksel_gfx, 144 prcm->cm_clksel1_core, 145 prcm->cm_clksel_mdm); 146 147 /* x2 to enter omap2xxx_sdrc_init_params() */ 148 omap2xxx_sdrc_reprogram(CORE_CLK_SRC_DPLL_X2, 1); 149 150 omap2_set_prcm(prcm->cm_clksel1_pll, prcm->base_sdrc_rfr, 151 bypass); 152 153 omap2xxx_sdrc_init_params(omap2xxx_sdrc_dll_is_unlocked()); 154 omap2xxx_sdrc_reprogram(done_rate, 0); 155 156 local_irq_restore(flags); 157 } 158 159 return 0; 160 } 161 162 /** 163 * omap2xxx_clkt_vps_check_bootloader_rate - determine which of the rate 164 * table sets matches the current CORE DPLL hardware rate 165 * 166 * Check the MPU rate set by bootloader. Sets the 'curr_prcm_set' 167 * global to point to the active rate set when found; otherwise, sets 168 * it to NULL. No return value; 169 */ 170 void omap2xxx_clkt_vps_check_bootloader_rates(void) 171 { 172 const struct prcm_config *prcm = NULL; 173 unsigned long rate; 174 175 rate = omap2xxx_clk_get_core_rate(); 176 for (prcm = rate_table; prcm->mpu_speed; prcm++) { 177 if (!(prcm->flags & cpu_mask)) 178 continue; 179 if (prcm->xtal_speed != sys_ck_rate) 180 continue; 181 if (prcm->dpll_speed <= rate) 182 break; 183 } 184 curr_prcm_set = prcm; 185 } 186 187 /** 188 * omap2xxx_clkt_vps_late_init - store a copy of the sys_ck rate 189 * 190 * Store a copy of the sys_ck rate for later use by the OMAP2xxx DVFS 191 * code. (The sys_ck rate does not -- or rather, must not -- change 192 * during kernel runtime.) Must be called after we have a valid 193 * sys_ck rate, but before the virt_prcm_set clock rate is 194 * recalculated. No return value. 195 */ 196 void omap2xxx_clkt_vps_late_init(void) 197 { 198 struct clk *c; 199 200 c = clk_get(NULL, "sys_ck"); 201 if (IS_ERR(c)) { 202 WARN(1, "could not locate sys_ck\n"); 203 } else { 204 sys_ck_rate = clk_get_rate(c); 205 clk_put(c); 206 } 207 } 208 209 #ifdef CONFIG_OF 210 #include <linux/clk-provider.h> 211 #include <linux/clkdev.h> 212 213 static const struct clk_ops virt_prcm_set_ops = { 214 .recalc_rate = &omap2_table_mpu_recalc, 215 .set_rate = &omap2_select_table_rate, 216 .round_rate = &omap2_round_to_table_rate, 217 }; 218 219 /** 220 * omap2xxx_clkt_vps_init - initialize virt_prcm_set clock 221 * 222 * Does a manual init for the virtual prcm DVFS clock for OMAP2. This 223 * function is called only from omap2 DT clock init, as the virtual 224 * node is not modelled in the DT clock data. 225 */ 226 void omap2xxx_clkt_vps_init(void) 227 { 228 struct clk_init_data init = { NULL }; 229 struct clk_hw_omap *hw = NULL; 230 struct clk *clk; 231 const char *parent_name = "mpu_ck"; 232 233 omap2xxx_clkt_vps_late_init(); 234 omap2xxx_clkt_vps_check_bootloader_rates(); 235 236 hw = kzalloc(sizeof(*hw), GFP_KERNEL); 237 if (!hw) 238 goto cleanup; 239 init.name = "virt_prcm_set"; 240 init.ops = &virt_prcm_set_ops; 241 init.parent_names = &parent_name; 242 init.num_parents = 1; 243 244 hw->hw.init = &init; 245 246 clk = clk_register(NULL, &hw->hw); 247 clkdev_create(clk, "cpufreq_ck", NULL); 248 return; 249 cleanup: 250 kfree(hw); 251 } 252 #endif 253