1 /* 2 * arch/arm/mach-lpc32xx/pm.c 3 * 4 * Original authors: Vitaly Wool, Dmitry Chigirev <source@mvista.com> 5 * Modified by Kevin Wells <kevin.wells@nxp.com> 6 * 7 * 2005 (c) MontaVista Software, Inc. This file is licensed under 8 * the terms of the GNU General Public License version 2. This program 9 * is licensed "as is" without any warranty of any kind, whether express 10 * or implied. 11 */ 12 13 /* 14 * LPC32XX CPU and system power management 15 * 16 * The LPC32XX has three CPU modes for controlling system power: run, 17 * direct-run, and halt modes. When switching between halt and run modes, 18 * the CPU transistions through direct-run mode. For Linux, direct-run 19 * mode is not used in normal operation. Halt mode is used when the 20 * system is fully suspended. 21 * 22 * Run mode: 23 * The ARM CPU clock (HCLK_PLL), HCLK bus clock, and PCLK bus clocks are 24 * derived from the HCLK PLL. The HCLK and PCLK bus rates are divided from 25 * the HCLK_PLL rate. Linux runs in this mode. 26 * 27 * Direct-run mode: 28 * The ARM CPU clock, HCLK bus clock, and PCLK bus clocks are driven from 29 * SYSCLK. SYSCLK is usually around 13MHz, but may vary based on SYSCLK 30 * source or the frequency of the main oscillator. In this mode, the 31 * HCLK_PLL can be safely enabled, changed, or disabled. 32 * 33 * Halt mode: 34 * SYSCLK is gated off and the CPU and system clocks are halted. 35 * Peripherals based on the 32KHz oscillator clock (ie, RTC, touch, 36 * key scanner, etc.) still operate if enabled. In this state, an enabled 37 * system event (ie, GPIO state change, RTC match, key press, etc.) will 38 * wake the system up back into direct-run mode. 39 * 40 * DRAM refresh 41 * DRAM clocking and refresh are slightly different for systems with DDR 42 * DRAM or regular SDRAM devices. If SDRAM is used in the system, the 43 * SDRAM will still be accessible in direct-run mode. In DDR based systems, 44 * a transition to direct-run mode will stop all DDR accesses (no clocks). 45 * Because of this, the code to switch power modes and the code to enter 46 * and exit DRAM self-refresh modes must not be executed in DRAM. A small 47 * section of IRAM is used instead for this. 48 * 49 * Suspend is handled with the following logic: 50 * Backup a small area of IRAM used for the suspend code 51 * Copy suspend code to IRAM 52 * Transfer control to code in IRAM 53 * Places DRAMs in self-refresh mode 54 * Enter direct-run mode 55 * Save state of HCLK_PLL PLL 56 * Disable HCLK_PLL PLL 57 * Enter halt mode - CPU and buses will stop 58 * System enters direct-run mode when an enabled event occurs 59 * HCLK PLL state is restored 60 * Run mode is entered 61 * DRAMS are placed back into normal mode 62 * Code execution returns from IRAM 63 * IRAM code are used for suspend is restored 64 * Suspend mode is exited 65 */ 66 67 #include <linux/suspend.h> 68 #include <linux/io.h> 69 #include <linux/slab.h> 70 71 #include <asm/cacheflush.h> 72 73 #include <mach/hardware.h> 74 #include <mach/platform.h> 75 #include "common.h" 76 77 #define TEMP_IRAM_AREA IO_ADDRESS(LPC32XX_IRAM_BASE) 78 79 /* 80 * Both STANDBY and MEM suspend states are handled the same with no 81 * loss of CPU or memory state 82 */ 83 static int lpc32xx_pm_enter(suspend_state_t state) 84 { 85 int (*lpc32xx_suspend_ptr) (void); 86 void *iram_swap_area; 87 88 /* Allocate some space for temporary IRAM storage */ 89 iram_swap_area = kmemdup((void *)TEMP_IRAM_AREA, 90 lpc32xx_sys_suspend_sz, GFP_KERNEL); 91 if (!iram_swap_area) 92 return -ENOMEM; 93 94 /* 95 * Copy code to suspend system into IRAM. The suspend code 96 * needs to run from IRAM as DRAM may no longer be available 97 * when the PLL is stopped. 98 */ 99 memcpy((void *) TEMP_IRAM_AREA, &lpc32xx_sys_suspend, 100 lpc32xx_sys_suspend_sz); 101 flush_icache_range((unsigned long)TEMP_IRAM_AREA, 102 (unsigned long)(TEMP_IRAM_AREA) + lpc32xx_sys_suspend_sz); 103 104 /* Transfer to suspend code in IRAM */ 105 lpc32xx_suspend_ptr = (void *) TEMP_IRAM_AREA; 106 flush_cache_all(); 107 (void) lpc32xx_suspend_ptr(); 108 109 /* Restore original IRAM contents */ 110 memcpy((void *) TEMP_IRAM_AREA, iram_swap_area, 111 lpc32xx_sys_suspend_sz); 112 113 kfree(iram_swap_area); 114 115 return 0; 116 } 117 118 static const struct platform_suspend_ops lpc32xx_pm_ops = { 119 .valid = suspend_valid_only_mem, 120 .enter = lpc32xx_pm_enter, 121 }; 122 123 #define EMC_DYN_MEM_CTRL_OFS 0x20 124 #define EMC_SRMMC (1 << 3) 125 #define EMC_CTRL_REG io_p2v(LPC32XX_EMC_BASE + EMC_DYN_MEM_CTRL_OFS) 126 static int __init lpc32xx_pm_init(void) 127 { 128 /* 129 * Setup SDRAM self-refresh clock to automatically disable o 130 * start of self-refresh. This only needs to be done once. 131 */ 132 __raw_writel(__raw_readl(EMC_CTRL_REG) | EMC_SRMMC, EMC_CTRL_REG); 133 134 suspend_set_ops(&lpc32xx_pm_ops); 135 136 return 0; 137 } 138 arch_initcall(lpc32xx_pm_init); 139