1/* SPDX-License-Identifier: GPL-2.0-only */ 2/* 3 * arch/arm/mach-at91/pm_slow_clock.S 4 * 5 * Copyright (C) 2006 Savin Zlobec 6 * 7 * AT91SAM9 support: 8 * Copyright (C) 2007 Anti Sullin <anti.sullin@artecdesign.ee> 9 */ 10#include <linux/linkage.h> 11#include <linux/clk/at91_pmc.h> 12#include "pm.h" 13#include "pm_data-offsets.h" 14 15#define SRAMC_SELF_FRESH_ACTIVE 0x01 16#define SRAMC_SELF_FRESH_EXIT 0x00 17 18pmc .req r0 19tmp1 .req r4 20tmp2 .req r5 21tmp3 .req r6 22 23/* 24 * Wait until master clock is ready (after switching master clock source) 25 * 26 * @r_mckid: register holding master clock identifier 27 * 28 * Side effects: overwrites r7, r8 29 */ 30 .macro wait_mckrdy r_mckid 31#ifdef CONFIG_SOC_SAMA7 32 cmp \r_mckid, #0 33 beq 1f 34 mov r7, #AT91_PMC_MCKXRDY 35 b 2f 36#endif 371: mov r7, #AT91_PMC_MCKRDY 382: ldr r8, [pmc, #AT91_PMC_SR] 39 and r8, r7 40 cmp r8, r7 41 bne 2b 42 .endm 43 44/* 45 * Wait until master oscillator has stabilized. 46 * 47 * Side effects: overwrites r7 48 */ 49 .macro wait_moscrdy 501: ldr r7, [pmc, #AT91_PMC_SR] 51 tst r7, #AT91_PMC_MOSCS 52 beq 1b 53 .endm 54 55/* 56 * Wait for main oscillator selection is done 57 * 58 * Side effects: overwrites r7 59 */ 60 .macro wait_moscsels 611: ldr r7, [pmc, #AT91_PMC_SR] 62 tst r7, #AT91_PMC_MOSCSELS 63 beq 1b 64 .endm 65 66/* 67 * Put the processor to enter the idle state 68 * 69 * Side effects: overwrites r7 70 */ 71 .macro at91_cpu_idle 72 73#if defined(CONFIG_CPU_V7) 74 mov r7, #AT91_PMC_PCK 75 str r7, [pmc, #AT91_PMC_SCDR] 76 77 dsb 78 79 wfi @ Wait For Interrupt 80#else 81 mcr p15, 0, tmp1, c7, c0, 4 82#endif 83 84 .endm 85 86/** 87 * Set state for 2.5V low power regulator 88 * @ena: 0 - disable regulator 89 * 1 - enable regulator 90 * 91 * Side effects: overwrites r7, r8, r9, r10 92 */ 93 .macro at91_2_5V_reg_set_low_power ena 94#ifdef CONFIG_SOC_SAMA7 95 ldr r7, .sfrbu 96 mov r8, #\ena 97 ldr r9, [r7, #AT91_SFRBU_25LDOCR] 98 orr r9, r9, #AT91_SFRBU_25LDOCR_LP 99 cmp r8, #1 100 beq lp_done_\ena 101 bic r9, r9, #AT91_SFRBU_25LDOCR_LP 102lp_done_\ena: 103 ldr r10, =AT91_SFRBU_25LDOCR_LDOANAKEY 104 orr r9, r9, r10 105 str r9, [r7, #AT91_SFRBU_25LDOCR] 106#endif 107 .endm 108 109 .macro at91_backup_set_lpm reg 110#ifdef CONFIG_SOC_SAMA7 111 orr \reg, \reg, #0x200000 112#endif 113 .endm 114 115 .text 116 117 .arm 118 119#ifdef CONFIG_SOC_SAMA7 120/** 121 * Enable self-refresh 122 * 123 * Side effects: overwrites r2, r3, tmp1, tmp2, tmp3, r7 124 */ 125.macro at91_sramc_self_refresh_ena 126 ldr r2, .sramc_base 127 ldr r3, .sramc_phy_base 128 ldr r7, .pm_mode 129 130 dsb 131 132 /* Disable all AXI ports. */ 133 ldr tmp1, [r2, #UDDRC_PCTRL_0] 134 bic tmp1, tmp1, #0x1 135 str tmp1, [r2, #UDDRC_PCTRL_0] 136 137 ldr tmp1, [r2, #UDDRC_PCTRL_1] 138 bic tmp1, tmp1, #0x1 139 str tmp1, [r2, #UDDRC_PCTRL_1] 140 141 ldr tmp1, [r2, #UDDRC_PCTRL_2] 142 bic tmp1, tmp1, #0x1 143 str tmp1, [r2, #UDDRC_PCTRL_2] 144 145 ldr tmp1, [r2, #UDDRC_PCTRL_3] 146 bic tmp1, tmp1, #0x1 147 str tmp1, [r2, #UDDRC_PCTRL_3] 148 149 ldr tmp1, [r2, #UDDRC_PCTRL_4] 150 bic tmp1, tmp1, #0x1 151 str tmp1, [r2, #UDDRC_PCTRL_4] 152 153sr_ena_1: 154 /* Wait for all ports to disable. */ 155 ldr tmp1, [r2, #UDDRC_PSTAT] 156 ldr tmp2, =UDDRC_PSTAT_ALL_PORTS 157 tst tmp1, tmp2 158 bne sr_ena_1 159 160 /* Switch to self-refresh. */ 161 ldr tmp1, [r2, #UDDRC_PWRCTL] 162 orr tmp1, tmp1, #UDDRC_PWRCTRL_SELFREF_SW 163 str tmp1, [r2, #UDDRC_PWRCTL] 164 165sr_ena_2: 166 /* Wait for self-refresh enter. */ 167 ldr tmp1, [r2, #UDDRC_STAT] 168 bic tmp1, tmp1, #~UDDRC_STAT_SELFREF_TYPE_MSK 169 cmp tmp1, #UDDRC_STAT_SELFREF_TYPE_SW 170 bne sr_ena_2 171 172 /* Put DDR PHY's DLL in bypass mode for non-backup modes. */ 173 cmp r7, #AT91_PM_BACKUP 174 beq sr_ena_3 175 ldr tmp1, [r3, #DDR3PHY_PIR] 176 orr tmp1, tmp1, #DDR3PHY_PIR_DLLBYP 177 str tmp1, [r3, #DDR3PHY_PIR] 178 179sr_ena_3: 180 /* Power down DDR PHY data receivers. */ 181 ldr tmp1, [r3, #DDR3PHY_DXCCR] 182 orr tmp1, tmp1, #DDR3PHY_DXCCR_DXPDR 183 str tmp1, [r3, #DDR3PHY_DXCCR] 184 185 /* Power down ADDR/CMD IO. */ 186 ldr tmp1, [r3, #DDR3PHY_ACIOCR] 187 orr tmp1, tmp1, #DDR3PHY_ACIORC_ACPDD 188 orr tmp1, tmp1, #DDR3PHY_ACIOCR_CKPDD_CK0 189 orr tmp1, tmp1, #DDR3PHY_ACIOCR_CSPDD_CS0 190 str tmp1, [r3, #DDR3PHY_ACIOCR] 191 192 /* Power down ODT. */ 193 ldr tmp1, [r3, #DDR3PHY_DSGCR] 194 orr tmp1, tmp1, #DDR3PHY_DSGCR_ODTPDD_ODT0 195 str tmp1, [r3, #DDR3PHY_DSGCR] 196.endm 197 198/** 199 * Disable self-refresh 200 * 201 * Side effects: overwrites r2, r3, tmp1, tmp2, tmp3 202 */ 203.macro at91_sramc_self_refresh_dis 204 ldr r2, .sramc_base 205 ldr r3, .sramc_phy_base 206 207 /* Power up DDR PHY data receivers. */ 208 ldr tmp1, [r3, #DDR3PHY_DXCCR] 209 bic tmp1, tmp1, #DDR3PHY_DXCCR_DXPDR 210 str tmp1, [r3, #DDR3PHY_DXCCR] 211 212 /* Power up the output of CK and CS pins. */ 213 ldr tmp1, [r3, #DDR3PHY_ACIOCR] 214 bic tmp1, tmp1, #DDR3PHY_ACIORC_ACPDD 215 bic tmp1, tmp1, #DDR3PHY_ACIOCR_CKPDD_CK0 216 bic tmp1, tmp1, #DDR3PHY_ACIOCR_CSPDD_CS0 217 str tmp1, [r3, #DDR3PHY_ACIOCR] 218 219 /* Power up ODT. */ 220 ldr tmp1, [r3, #DDR3PHY_DSGCR] 221 bic tmp1, tmp1, #DDR3PHY_DSGCR_ODTPDD_ODT0 222 str tmp1, [r3, #DDR3PHY_DSGCR] 223 224 /* Take DDR PHY's DLL out of bypass mode. */ 225 ldr tmp1, [r3, #DDR3PHY_PIR] 226 bic tmp1, tmp1, #DDR3PHY_PIR_DLLBYP 227 str tmp1, [r3, #DDR3PHY_PIR] 228 229 /* Enable quasi-dynamic programming. */ 230 mov tmp1, #0 231 str tmp1, [r2, #UDDRC_SWCTRL] 232 233 /* De-assert SDRAM initialization. */ 234 ldr tmp1, [r2, #UDDRC_DFIMISC] 235 bic tmp1, tmp1, #UDDRC_DFIMISC_DFI_INIT_COMPLETE_EN 236 str tmp1, [r2, #UDDRC_DFIMISC] 237 238 /* Quasi-dynamic programming done. */ 239 mov tmp1, #UDDRC_SWCTRL_SW_DONE 240 str tmp1, [r2, #UDDRC_SWCTRL] 241 242sr_dis_1: 243 ldr tmp1, [r2, #UDDRC_SWSTAT] 244 tst tmp1, #UDDRC_SWSTAT_SW_DONE_ACK 245 beq sr_dis_1 246 247 /* DLL soft-reset + DLL lock wait + ITM reset */ 248 mov tmp1, #(DDR3PHY_PIR_INIT | DDR3PHY_PIR_DLLSRST | \ 249 DDR3PHY_PIR_DLLLOCK | DDR3PHY_PIR_ITMSRST) 250 str tmp1, [r3, #DDR3PHY_PIR] 251 252sr_dis_4: 253 /* Wait for it. */ 254 ldr tmp1, [r3, #DDR3PHY_PGSR] 255 tst tmp1, #DDR3PHY_PGSR_IDONE 256 beq sr_dis_4 257 258 /* Enable quasi-dynamic programming. */ 259 mov tmp1, #0 260 str tmp1, [r2, #UDDRC_SWCTRL] 261 262 /* Assert PHY init complete enable signal. */ 263 ldr tmp1, [r2, #UDDRC_DFIMISC] 264 orr tmp1, tmp1, #UDDRC_DFIMISC_DFI_INIT_COMPLETE_EN 265 str tmp1, [r2, #UDDRC_DFIMISC] 266 267 /* Programming is done. Set sw_done. */ 268 mov tmp1, #UDDRC_SWCTRL_SW_DONE 269 str tmp1, [r2, #UDDRC_SWCTRL] 270 271sr_dis_5: 272 /* Wait for it. */ 273 ldr tmp1, [r2, #UDDRC_SWSTAT] 274 tst tmp1, #UDDRC_SWSTAT_SW_DONE_ACK 275 beq sr_dis_5 276 277 /* Trigger self-refresh exit. */ 278 ldr tmp1, [r2, #UDDRC_PWRCTL] 279 bic tmp1, tmp1, #UDDRC_PWRCTRL_SELFREF_SW 280 str tmp1, [r2, #UDDRC_PWRCTL] 281 282sr_dis_6: 283 /* Wait for self-refresh exit done. */ 284 ldr tmp1, [r2, #UDDRC_STAT] 285 bic tmp1, tmp1, #~UDDRC_STAT_OPMODE_MSK 286 cmp tmp1, #UDDRC_STAT_OPMODE_NORMAL 287 bne sr_dis_6 288 289 /* Enable all AXI ports. */ 290 ldr tmp1, [r2, #UDDRC_PCTRL_0] 291 orr tmp1, tmp1, #0x1 292 str tmp1, [r2, #UDDRC_PCTRL_0] 293 294 ldr tmp1, [r2, #UDDRC_PCTRL_1] 295 orr tmp1, tmp1, #0x1 296 str tmp1, [r2, #UDDRC_PCTRL_1] 297 298 ldr tmp1, [r2, #UDDRC_PCTRL_2] 299 orr tmp1, tmp1, #0x1 300 str tmp1, [r2, #UDDRC_PCTRL_2] 301 302 ldr tmp1, [r2, #UDDRC_PCTRL_3] 303 orr tmp1, tmp1, #0x1 304 str tmp1, [r2, #UDDRC_PCTRL_3] 305 306 ldr tmp1, [r2, #UDDRC_PCTRL_4] 307 orr tmp1, tmp1, #0x1 308 str tmp1, [r2, #UDDRC_PCTRL_4] 309 310 dsb 311.endm 312#else 313/** 314 * Enable self-refresh 315 * 316 * register usage: 317 * @r1: memory type 318 * @r2: base address of the sram controller 319 * @r3: temporary 320 */ 321.macro at91_sramc_self_refresh_ena 322 ldr r1, .memtype 323 ldr r2, .sramc_base 324 325 cmp r1, #AT91_MEMCTRL_MC 326 bne sr_ena_ddrc_sf 327 328 /* Active SDRAM self-refresh mode */ 329 mov r3, #1 330 str r3, [r2, #AT91_MC_SDRAMC_SRR] 331 b sr_ena_exit 332 333sr_ena_ddrc_sf: 334 cmp r1, #AT91_MEMCTRL_DDRSDR 335 bne sr_ena_sdramc_sf 336 337 /* 338 * DDR Memory controller 339 */ 340 341 /* LPDDR1 --> force DDR2 mode during self-refresh */ 342 ldr r3, [r2, #AT91_DDRSDRC_MDR] 343 str r3, .saved_sam9_mdr 344 bic r3, r3, #~AT91_DDRSDRC_MD 345 cmp r3, #AT91_DDRSDRC_MD_LOW_POWER_DDR 346 ldreq r3, [r2, #AT91_DDRSDRC_MDR] 347 biceq r3, r3, #AT91_DDRSDRC_MD 348 orreq r3, r3, #AT91_DDRSDRC_MD_DDR2 349 streq r3, [r2, #AT91_DDRSDRC_MDR] 350 351 /* Active DDRC self-refresh mode */ 352 ldr r3, [r2, #AT91_DDRSDRC_LPR] 353 str r3, .saved_sam9_lpr 354 bic r3, r3, #AT91_DDRSDRC_LPCB 355 orr r3, r3, #AT91_DDRSDRC_LPCB_SELF_REFRESH 356 str r3, [r2, #AT91_DDRSDRC_LPR] 357 358 /* If using the 2nd ddr controller */ 359 ldr r2, .sramc1_base 360 cmp r2, #0 361 beq sr_ena_no_2nd_ddrc 362 363 ldr r3, [r2, #AT91_DDRSDRC_MDR] 364 str r3, .saved_sam9_mdr1 365 bic r3, r3, #~AT91_DDRSDRC_MD 366 cmp r3, #AT91_DDRSDRC_MD_LOW_POWER_DDR 367 ldreq r3, [r2, #AT91_DDRSDRC_MDR] 368 biceq r3, r3, #AT91_DDRSDRC_MD 369 orreq r3, r3, #AT91_DDRSDRC_MD_DDR2 370 streq r3, [r2, #AT91_DDRSDRC_MDR] 371 372 /* Active DDRC self-refresh mode */ 373 ldr r3, [r2, #AT91_DDRSDRC_LPR] 374 str r3, .saved_sam9_lpr1 375 bic r3, r3, #AT91_DDRSDRC_LPCB 376 orr r3, r3, #AT91_DDRSDRC_LPCB_SELF_REFRESH 377 str r3, [r2, #AT91_DDRSDRC_LPR] 378 379sr_ena_no_2nd_ddrc: 380 b sr_ena_exit 381 382 /* 383 * SDRAMC Memory controller 384 */ 385sr_ena_sdramc_sf: 386 /* Active SDRAMC self-refresh mode */ 387 ldr r3, [r2, #AT91_SDRAMC_LPR] 388 str r3, .saved_sam9_lpr 389 bic r3, r3, #AT91_SDRAMC_LPCB 390 orr r3, r3, #AT91_SDRAMC_LPCB_SELF_REFRESH 391 str r3, [r2, #AT91_SDRAMC_LPR] 392 393 ldr r3, .saved_sam9_lpr 394 str r3, [r2, #AT91_SDRAMC_LPR] 395 396sr_ena_exit: 397.endm 398 399/** 400 * Disable self-refresh 401 * 402 * register usage: 403 * @r1: memory type 404 * @r2: base address of the sram controller 405 * @r3: temporary 406 */ 407.macro at91_sramc_self_refresh_dis 408 ldr r1, .memtype 409 ldr r2, .sramc_base 410 411 cmp r1, #AT91_MEMCTRL_MC 412 bne sr_dis_ddrc_exit_sf 413 414 /* 415 * at91rm9200 Memory controller 416 */ 417 418 /* 419 * For exiting the self-refresh mode, do nothing, 420 * automatically exit the self-refresh mode. 421 */ 422 b sr_dis_exit 423 424sr_dis_ddrc_exit_sf: 425 cmp r1, #AT91_MEMCTRL_DDRSDR 426 bne sdramc_exit_sf 427 428 /* DDR Memory controller */ 429 430 /* Restore MDR in case of LPDDR1 */ 431 ldr r3, .saved_sam9_mdr 432 str r3, [r2, #AT91_DDRSDRC_MDR] 433 /* Restore LPR on AT91 with DDRAM */ 434 ldr r3, .saved_sam9_lpr 435 str r3, [r2, #AT91_DDRSDRC_LPR] 436 437 /* If using the 2nd ddr controller */ 438 ldr r2, .sramc1_base 439 cmp r2, #0 440 ldrne r3, .saved_sam9_mdr1 441 strne r3, [r2, #AT91_DDRSDRC_MDR] 442 ldrne r3, .saved_sam9_lpr1 443 strne r3, [r2, #AT91_DDRSDRC_LPR] 444 445 b sr_dis_exit 446 447sdramc_exit_sf: 448 /* SDRAMC Memory controller */ 449 ldr r3, .saved_sam9_lpr 450 str r3, [r2, #AT91_SDRAMC_LPR] 451 452sr_dis_exit: 453.endm 454#endif 455 456.macro at91_pm_ulp0_mode 457 ldr pmc, .pmc_base 458 ldr tmp2, .pm_mode 459 ldr tmp3, .mckr_offset 460 461 /* Check if ULP0 fast variant has been requested. */ 462 cmp tmp2, #AT91_PM_ULP0_FAST 463 bne 0f 464 465 /* Set highest prescaler for power saving */ 466 ldr tmp1, [pmc, tmp3] 467 bic tmp1, tmp1, #AT91_PMC_PRES 468 orr tmp1, tmp1, #AT91_PMC_PRES_64 469 str tmp1, [pmc, tmp3] 470 471 mov tmp3, #0 472 wait_mckrdy tmp3 473 b 1f 474 4750: 476 /* Turn off the crystal oscillator */ 477 ldr tmp1, [pmc, #AT91_CKGR_MOR] 478 bic tmp1, tmp1, #AT91_PMC_MOSCEN 479 orr tmp1, tmp1, #AT91_PMC_KEY 480 str tmp1, [pmc, #AT91_CKGR_MOR] 481 482 /* Save RC oscillator state */ 483 ldr tmp1, [pmc, #AT91_PMC_SR] 484 str tmp1, .saved_osc_status 485 tst tmp1, #AT91_PMC_MOSCRCS 486 bne 1f 487 488 /* Turn off RC oscillator */ 489 ldr tmp1, [pmc, #AT91_CKGR_MOR] 490 bic tmp1, tmp1, #AT91_PMC_MOSCRCEN 491 bic tmp1, tmp1, #AT91_PMC_KEY_MASK 492 orr tmp1, tmp1, #AT91_PMC_KEY 493 str tmp1, [pmc, #AT91_CKGR_MOR] 494 495 /* Wait main RC disabled done */ 4962: ldr tmp1, [pmc, #AT91_PMC_SR] 497 tst tmp1, #AT91_PMC_MOSCRCS 498 bne 2b 499 500 /* Wait for interrupt */ 5011: at91_cpu_idle 502 503 /* Check if ULP0 fast variant has been requested. */ 504 cmp tmp2, #AT91_PM_ULP0_FAST 505 bne 5f 506 507 /* Set lowest prescaler for fast resume. */ 508 ldr tmp3, .mckr_offset 509 ldr tmp1, [pmc, tmp3] 510 bic tmp1, tmp1, #AT91_PMC_PRES 511 str tmp1, [pmc, tmp3] 512 513 mov tmp3, #0 514 wait_mckrdy tmp3 515 b 6f 516 5175: /* Restore RC oscillator state */ 518 ldr tmp1, .saved_osc_status 519 tst tmp1, #AT91_PMC_MOSCRCS 520 beq 4f 521 522 /* Turn on RC oscillator */ 523 ldr tmp1, [pmc, #AT91_CKGR_MOR] 524 orr tmp1, tmp1, #AT91_PMC_MOSCRCEN 525 bic tmp1, tmp1, #AT91_PMC_KEY_MASK 526 orr tmp1, tmp1, #AT91_PMC_KEY 527 str tmp1, [pmc, #AT91_CKGR_MOR] 528 529 /* Wait main RC stabilization */ 5303: ldr tmp1, [pmc, #AT91_PMC_SR] 531 tst tmp1, #AT91_PMC_MOSCRCS 532 beq 3b 533 534 /* Turn on the crystal oscillator */ 5354: ldr tmp1, [pmc, #AT91_CKGR_MOR] 536 orr tmp1, tmp1, #AT91_PMC_MOSCEN 537 orr tmp1, tmp1, #AT91_PMC_KEY 538 str tmp1, [pmc, #AT91_CKGR_MOR] 539 540 wait_moscrdy 5416: 542.endm 543 544/** 545 * Note: This procedure only applies on the platform which uses 546 * the external crystal oscillator as a main clock source. 547 */ 548.macro at91_pm_ulp1_mode 549 ldr pmc, .pmc_base 550 ldr tmp2, .mckr_offset 551 mov tmp3, #0 552 553 /* Save RC oscillator state and check if it is enabled. */ 554 ldr tmp1, [pmc, #AT91_PMC_SR] 555 str tmp1, .saved_osc_status 556 tst tmp1, #AT91_PMC_MOSCRCS 557 bne 2f 558 559 /* Enable RC oscillator */ 560 ldr tmp1, [pmc, #AT91_CKGR_MOR] 561 orr tmp1, tmp1, #AT91_PMC_MOSCRCEN 562 bic tmp1, tmp1, #AT91_PMC_KEY_MASK 563 orr tmp1, tmp1, #AT91_PMC_KEY 564 str tmp1, [pmc, #AT91_CKGR_MOR] 565 566 /* Wait main RC stabilization */ 5671: ldr tmp1, [pmc, #AT91_PMC_SR] 568 tst tmp1, #AT91_PMC_MOSCRCS 569 beq 1b 570 571 /* Switch the main clock source to 12-MHz RC oscillator */ 5722: ldr tmp1, [pmc, #AT91_CKGR_MOR] 573 bic tmp1, tmp1, #AT91_PMC_MOSCSEL 574 bic tmp1, tmp1, #AT91_PMC_KEY_MASK 575 orr tmp1, tmp1, #AT91_PMC_KEY 576 str tmp1, [pmc, #AT91_CKGR_MOR] 577 578 wait_moscsels 579 580 /* Disable the crystal oscillator */ 581 ldr tmp1, [pmc, #AT91_CKGR_MOR] 582 bic tmp1, tmp1, #AT91_PMC_MOSCEN 583 bic tmp1, tmp1, #AT91_PMC_KEY_MASK 584 orr tmp1, tmp1, #AT91_PMC_KEY 585 str tmp1, [pmc, #AT91_CKGR_MOR] 586 587 /* Switch the master clock source to main clock */ 588 ldr tmp1, [pmc, tmp2] 589 bic tmp1, tmp1, #AT91_PMC_CSS 590 orr tmp1, tmp1, #AT91_PMC_CSS_MAIN 591 str tmp1, [pmc, tmp2] 592 593 wait_mckrdy tmp3 594 595 /* Enter the ULP1 mode by set WAITMODE bit in CKGR_MOR */ 596 ldr tmp1, [pmc, #AT91_CKGR_MOR] 597 orr tmp1, tmp1, #AT91_PMC_WAITMODE 598 bic tmp1, tmp1, #AT91_PMC_KEY_MASK 599 orr tmp1, tmp1, #AT91_PMC_KEY 600 str tmp1, [pmc, #AT91_CKGR_MOR] 601 602 /* Quirk for SAM9X60's PMC */ 603 nop 604 nop 605 606 wait_mckrdy tmp3 607 608 /* Enable the crystal oscillator */ 609 ldr tmp1, [pmc, #AT91_CKGR_MOR] 610 orr tmp1, tmp1, #AT91_PMC_MOSCEN 611 bic tmp1, tmp1, #AT91_PMC_KEY_MASK 612 orr tmp1, tmp1, #AT91_PMC_KEY 613 str tmp1, [pmc, #AT91_CKGR_MOR] 614 615 wait_moscrdy 616 617 /* Switch the master clock source to slow clock */ 618 ldr tmp1, [pmc, tmp2] 619 bic tmp1, tmp1, #AT91_PMC_CSS 620 str tmp1, [pmc, tmp2] 621 622 wait_mckrdy tmp3 623 624 /* Switch main clock source to crystal oscillator */ 625 ldr tmp1, [pmc, #AT91_CKGR_MOR] 626 orr tmp1, tmp1, #AT91_PMC_MOSCSEL 627 bic tmp1, tmp1, #AT91_PMC_KEY_MASK 628 orr tmp1, tmp1, #AT91_PMC_KEY 629 str tmp1, [pmc, #AT91_CKGR_MOR] 630 631 wait_moscsels 632 633 /* Switch the master clock source to main clock */ 634 ldr tmp1, [pmc, tmp2] 635 bic tmp1, tmp1, #AT91_PMC_CSS 636 orr tmp1, tmp1, #AT91_PMC_CSS_MAIN 637 str tmp1, [pmc, tmp2] 638 639 wait_mckrdy tmp3 640 641 /* Restore RC oscillator state */ 642 ldr tmp1, .saved_osc_status 643 tst tmp1, #AT91_PMC_MOSCRCS 644 bne 3f 645 646 /* Disable RC oscillator */ 647 ldr tmp1, [pmc, #AT91_CKGR_MOR] 648 bic tmp1, tmp1, #AT91_PMC_MOSCRCEN 649 bic tmp1, tmp1, #AT91_PMC_KEY_MASK 650 orr tmp1, tmp1, #AT91_PMC_KEY 651 str tmp1, [pmc, #AT91_CKGR_MOR] 652 653 /* Wait RC oscillator disable done */ 6544: ldr tmp1, [pmc, #AT91_PMC_SR] 655 tst tmp1, #AT91_PMC_MOSCRCS 656 bne 4b 657 6583: 659.endm 660 661.macro at91_plla_disable 662 /* Save PLLA setting and disable it */ 663 ldr tmp1, .pmc_version 664 cmp tmp1, #AT91_PMC_V1 665 beq 1f 666 667#ifdef CONFIG_HAVE_AT91_SAM9X60_PLL 668 /* Save PLLA settings. */ 669 ldr tmp2, [pmc, #AT91_PMC_PLL_UPDT] 670 bic tmp2, tmp2, #AT91_PMC_PLL_UPDT_ID 671 str tmp2, [pmc, #AT91_PMC_PLL_UPDT] 672 673 /* save div. */ 674 mov tmp1, #0 675 ldr tmp2, [pmc, #AT91_PMC_PLL_CTRL0] 676 bic tmp2, tmp2, #0xffffff00 677 orr tmp1, tmp1, tmp2 678 679 /* save mul. */ 680 ldr tmp2, [pmc, #AT91_PMC_PLL_CTRL1] 681 bic tmp2, tmp2, #0xffffff 682 orr tmp1, tmp1, tmp2 683 str tmp1, .saved_pllar 684 685 /* step 2. */ 686 ldr tmp1, [pmc, #AT91_PMC_PLL_UPDT] 687 bic tmp1, tmp1, #AT91_PMC_PLL_UPDT_UPDATE 688 bic tmp1, tmp1, #AT91_PMC_PLL_UPDT_ID 689 str tmp1, [pmc, #AT91_PMC_PLL_UPDT] 690 691 /* step 3. */ 692 ldr tmp1, [pmc, #AT91_PMC_PLL_CTRL0] 693 bic tmp1, tmp1, #AT91_PMC_PLL_CTRL0_ENPLLCK 694 orr tmp1, tmp1, #AT91_PMC_PLL_CTRL0_ENPLL 695 str tmp1, [pmc, #AT91_PMC_PLL_CTRL0] 696 697 /* step 4. */ 698 ldr tmp1, [pmc, #AT91_PMC_PLL_UPDT] 699 orr tmp1, tmp1, #AT91_PMC_PLL_UPDT_UPDATE 700 bic tmp1, tmp1, #AT91_PMC_PLL_UPDT_ID 701 str tmp1, [pmc, #AT91_PMC_PLL_UPDT] 702 703 /* step 5. */ 704 ldr tmp1, [pmc, #AT91_PMC_PLL_CTRL0] 705 bic tmp1, tmp1, #AT91_PMC_PLL_CTRL0_ENPLL 706 str tmp1, [pmc, #AT91_PMC_PLL_CTRL0] 707 708 /* step 7. */ 709 ldr tmp1, [pmc, #AT91_PMC_PLL_UPDT] 710 orr tmp1, tmp1, #AT91_PMC_PLL_UPDT_UPDATE 711 bic tmp1, tmp1, #AT91_PMC_PLL_UPDT_ID 712 str tmp1, [pmc, #AT91_PMC_PLL_UPDT] 713 714 b 2f 715#endif 716 7171: /* Save PLLA setting and disable it */ 718 ldr tmp1, [pmc, #AT91_CKGR_PLLAR] 719 str tmp1, .saved_pllar 720 721 /* Disable PLLA. */ 722 mov tmp1, #AT91_PMC_PLLCOUNT 723 orr tmp1, tmp1, #(1 << 29) /* bit 29 always set */ 724 str tmp1, [pmc, #AT91_CKGR_PLLAR] 7252: 726.endm 727 728.macro at91_plla_enable 729 ldr tmp2, .saved_pllar 730 ldr tmp3, .pmc_version 731 cmp tmp3, #AT91_PMC_V1 732 beq 4f 733 734#ifdef CONFIG_HAVE_AT91_SAM9X60_PLL 735 /* step 1. */ 736 ldr tmp1, [pmc, #AT91_PMC_PLL_UPDT] 737 bic tmp1, tmp1, #AT91_PMC_PLL_UPDT_ID 738 bic tmp1, tmp1, #AT91_PMC_PLL_UPDT_UPDATE 739 str tmp1, [pmc, #AT91_PMC_PLL_UPDT] 740 741 /* step 2. */ 742 ldr tmp1, =AT91_PMC_PLL_ACR_DEFAULT_PLLA 743 str tmp1, [pmc, #AT91_PMC_PLL_ACR] 744 745 /* step 3. */ 746 ldr tmp1, [pmc, #AT91_PMC_PLL_CTRL1] 747 mov tmp3, tmp2 748 bic tmp3, tmp3, #0xffffff 749 orr tmp1, tmp1, tmp3 750 str tmp1, [pmc, #AT91_PMC_PLL_CTRL1] 751 752 /* step 8. */ 753 ldr tmp1, [pmc, #AT91_PMC_PLL_UPDT] 754 bic tmp1, tmp1, #AT91_PMC_PLL_UPDT_ID 755 orr tmp1, tmp1, #AT91_PMC_PLL_UPDT_UPDATE 756 str tmp1, [pmc, #AT91_PMC_PLL_UPDT] 757 758 /* step 9. */ 759 ldr tmp1, [pmc, #AT91_PMC_PLL_CTRL0] 760 orr tmp1, tmp1, #AT91_PMC_PLL_CTRL0_ENLOCK 761 orr tmp1, tmp1, #AT91_PMC_PLL_CTRL0_ENPLL 762 orr tmp1, tmp1, #AT91_PMC_PLL_CTRL0_ENPLLCK 763 bic tmp1, tmp1, #0xff 764 mov tmp3, tmp2 765 bic tmp3, tmp3, #0xffffff00 766 orr tmp1, tmp1, tmp3 767 str tmp1, [pmc, #AT91_PMC_PLL_CTRL0] 768 769 /* step 10. */ 770 ldr tmp1, [pmc, #AT91_PMC_PLL_UPDT] 771 orr tmp1, tmp1, #AT91_PMC_PLL_UPDT_UPDATE 772 bic tmp1, tmp1, #AT91_PMC_PLL_UPDT_ID 773 str tmp1, [pmc, #AT91_PMC_PLL_UPDT] 774 775 /* step 11. */ 7763: ldr tmp1, [pmc, #AT91_PMC_PLL_ISR0] 777 tst tmp1, #0x1 778 beq 3b 779 b 2f 780#endif 781 782 /* Restore PLLA setting */ 7834: str tmp2, [pmc, #AT91_CKGR_PLLAR] 784 785 /* Enable PLLA. */ 786 tst tmp2, #(AT91_PMC_MUL & 0xff0000) 787 bne 1f 788 tst tmp2, #(AT91_PMC_MUL & ~0xff0000) 789 beq 2f 790 7911: ldr tmp1, [pmc, #AT91_PMC_SR] 792 tst tmp1, #AT91_PMC_LOCKA 793 beq 1b 7942: 795.endm 796 797/** 798 * at91_mckx_ps_enable: save MCK1..4 settings and switch it to main clock 799 * 800 * Side effects: overwrites tmp1, tmp2 801 */ 802.macro at91_mckx_ps_enable 803#ifdef CONFIG_SOC_SAMA7 804 ldr pmc, .pmc_base 805 806 /* There are 4 MCKs we need to handle: MCK1..4 */ 807 mov tmp1, #1 808e_loop: cmp tmp1, #5 809 beq e_done 810 811 /* Write MCK ID to retrieve the settings. */ 812 str tmp1, [pmc, #AT91_PMC_MCR_V2] 813 ldr tmp2, [pmc, #AT91_PMC_MCR_V2] 814 815e_save_mck1: 816 cmp tmp1, #1 817 bne e_save_mck2 818 str tmp2, .saved_mck1 819 b e_ps 820 821e_save_mck2: 822 cmp tmp1, #2 823 bne e_save_mck3 824 str tmp2, .saved_mck2 825 b e_ps 826 827e_save_mck3: 828 cmp tmp1, #3 829 bne e_save_mck4 830 str tmp2, .saved_mck3 831 b e_ps 832 833e_save_mck4: 834 str tmp2, .saved_mck4 835 836e_ps: 837 /* Use CSS=MAINCK and DIV=1. */ 838 bic tmp2, tmp2, #AT91_PMC_MCR_V2_CSS 839 bic tmp2, tmp2, #AT91_PMC_MCR_V2_DIV 840 orr tmp2, tmp2, #AT91_PMC_MCR_V2_CSS_MAINCK 841 orr tmp2, tmp2, #AT91_PMC_MCR_V2_DIV1 842 str tmp2, [pmc, #AT91_PMC_MCR_V2] 843 844 wait_mckrdy tmp1 845 846 add tmp1, tmp1, #1 847 b e_loop 848 849e_done: 850#endif 851.endm 852 853/** 854 * at91_mckx_ps_restore: restore MCK1..4 settings 855 * 856 * Side effects: overwrites tmp1, tmp2 857 */ 858.macro at91_mckx_ps_restore 859#ifdef CONFIG_SOC_SAMA7 860 ldr pmc, .pmc_base 861 862 /* There are 4 MCKs we need to handle: MCK1..4 */ 863 mov tmp1, #1 864r_loop: cmp tmp1, #5 865 beq r_done 866 867r_save_mck1: 868 cmp tmp1, #1 869 bne r_save_mck2 870 ldr tmp2, .saved_mck1 871 b r_ps 872 873r_save_mck2: 874 cmp tmp1, #2 875 bne r_save_mck3 876 ldr tmp2, .saved_mck2 877 b r_ps 878 879r_save_mck3: 880 cmp tmp1, #3 881 bne r_save_mck4 882 ldr tmp2, .saved_mck3 883 b r_ps 884 885r_save_mck4: 886 ldr tmp2, .saved_mck4 887 888r_ps: 889 /* Write MCK ID to retrieve the settings. */ 890 str tmp1, [pmc, #AT91_PMC_MCR_V2] 891 ldr tmp3, [pmc, #AT91_PMC_MCR_V2] 892 893 /* We need to restore CSS and DIV. */ 894 bic tmp3, tmp3, #AT91_PMC_MCR_V2_CSS 895 bic tmp3, tmp3, #AT91_PMC_MCR_V2_DIV 896 orr tmp3, tmp3, tmp2 897 bic tmp3, tmp3, #AT91_PMC_MCR_V2_ID_MSK 898 orr tmp3, tmp3, tmp1 899 orr tmp3, tmp3, #AT91_PMC_MCR_V2_CMD 900 str tmp2, [pmc, #AT91_PMC_MCR_V2] 901 902 wait_mckrdy tmp1 903 904 add tmp1, tmp1, #1 905 b r_loop 906r_done: 907#endif 908.endm 909 910.macro at91_ulp_mode 911 at91_mckx_ps_enable 912 913 ldr pmc, .pmc_base 914 ldr tmp2, .mckr_offset 915 ldr tmp3, .pm_mode 916 917 /* Save Master clock setting */ 918 ldr tmp1, [pmc, tmp2] 919 str tmp1, .saved_mckr 920 921 /* 922 * Set master clock source to: 923 * - MAINCK if using ULP0 fast variant 924 * - slow clock, otherwise 925 */ 926 bic tmp1, tmp1, #AT91_PMC_CSS 927 cmp tmp3, #AT91_PM_ULP0_FAST 928 bne save_mck 929 orr tmp1, tmp1, #AT91_PMC_CSS_MAIN 930save_mck: 931 str tmp1, [pmc, tmp2] 932 933 mov tmp3, #0 934 wait_mckrdy tmp3 935 936 at91_plla_disable 937 938 /* Enable low power mode for 2.5V regulator. */ 939 at91_2_5V_reg_set_low_power 1 940 941 ldr tmp3, .pm_mode 942 cmp tmp3, #AT91_PM_ULP1 943 beq ulp1_mode 944 945 at91_pm_ulp0_mode 946 b ulp_exit 947 948ulp1_mode: 949 at91_pm_ulp1_mode 950 b ulp_exit 951 952ulp_exit: 953 /* Disable low power mode for 2.5V regulator. */ 954 at91_2_5V_reg_set_low_power 0 955 956 ldr pmc, .pmc_base 957 958 at91_plla_enable 959 960 /* 961 * Restore master clock setting 962 */ 963 ldr tmp1, .mckr_offset 964 ldr tmp2, .saved_mckr 965 str tmp2, [pmc, tmp1] 966 967 mov tmp3, #0 968 wait_mckrdy tmp3 969 970 at91_mckx_ps_restore 971.endm 972 973.macro at91_backup_mode 974 /* Switch the master clock source to slow clock. */ 975 ldr pmc, .pmc_base 976 ldr tmp2, .mckr_offset 977 ldr tmp1, [pmc, tmp2] 978 bic tmp1, tmp1, #AT91_PMC_CSS 979 str tmp1, [pmc, tmp2] 980 981 mov tmp3, #0 982 wait_mckrdy tmp3 983 984 /*BUMEN*/ 985 ldr r0, .sfrbu 986 mov tmp1, #0x1 987 str tmp1, [r0, #0x10] 988 989 /* Wait for it. */ 9901: ldr tmp1, [r0, #0x10] 991 tst tmp1, #0x1 992 beq 1b 993 994 /* Shutdown */ 995 ldr r0, .shdwc 996 mov tmp1, #0xA5000000 997 add tmp1, tmp1, #0x1 998 at91_backup_set_lpm tmp1 999 str tmp1, [r0, #0] 1000.endm 1001 1002/* 1003 * void at91_suspend_sram_fn(struct at91_pm_data*) 1004 * @input param: 1005 * @r0: base address of struct at91_pm_data 1006 */ 1007/* at91_pm_suspend_in_sram must be 8-byte aligned per the requirements of fncpy() */ 1008 .align 3 1009ENTRY(at91_pm_suspend_in_sram) 1010 /* Save registers on stack */ 1011 stmfd sp!, {r4 - r12, lr} 1012 1013 /* Drain write buffer */ 1014 mov tmp1, #0 1015 mcr p15, 0, tmp1, c7, c10, 4 1016 1017 /* Flush tlb. */ 1018 mov r4, #0 1019 mcr p15, 0, r4, c8, c7, 0 1020 1021 ldr tmp1, [r0, #PM_DATA_PMC_MCKR_OFFSET] 1022 str tmp1, .mckr_offset 1023 ldr tmp1, [r0, #PM_DATA_PMC_VERSION] 1024 str tmp1, .pmc_version 1025 ldr tmp1, [r0, #PM_DATA_MEMCTRL] 1026 str tmp1, .memtype 1027 ldr tmp1, [r0, #PM_DATA_MODE] 1028 str tmp1, .pm_mode 1029 1030 /* 1031 * ldrne below are here to preload their address in the TLB as access 1032 * to RAM may be limited while in self-refresh. 1033 */ 1034 ldr tmp1, [r0, #PM_DATA_PMC] 1035 str tmp1, .pmc_base 1036 cmp tmp1, #0 1037 ldrne tmp2, [tmp1, #0] 1038 1039 ldr tmp1, [r0, #PM_DATA_RAMC0] 1040 str tmp1, .sramc_base 1041 cmp tmp1, #0 1042 ldrne tmp2, [tmp1, #0] 1043 1044 ldr tmp1, [r0, #PM_DATA_RAMC1] 1045 str tmp1, .sramc1_base 1046 cmp tmp1, #0 1047 ldrne tmp2, [tmp1, #0] 1048 1049#ifndef CONFIG_SOC_SAM_V4_V5 1050 /* ldrne below are here to preload their address in the TLB */ 1051 ldr tmp1, [r0, #PM_DATA_RAMC_PHY] 1052 str tmp1, .sramc_phy_base 1053 cmp tmp1, #0 1054 ldrne tmp2, [tmp1, #0] 1055 1056 ldr tmp1, [r0, #PM_DATA_SHDWC] 1057 str tmp1, .shdwc 1058 cmp tmp1, #0 1059 ldrne tmp2, [tmp1, #0] 1060 1061 ldr tmp1, [r0, #PM_DATA_SFRBU] 1062 str tmp1, .sfrbu 1063 cmp tmp1, #0 1064 ldrne tmp2, [tmp1, #0x10] 1065#endif 1066 1067 /* Active the self-refresh mode */ 1068 at91_sramc_self_refresh_ena 1069 1070 ldr r0, .pm_mode 1071 cmp r0, #AT91_PM_STANDBY 1072 beq standby 1073 cmp r0, #AT91_PM_BACKUP 1074 beq backup_mode 1075 1076 at91_ulp_mode 1077 b exit_suspend 1078 1079standby: 1080 /* Wait for interrupt */ 1081 ldr pmc, .pmc_base 1082 at91_cpu_idle 1083 b exit_suspend 1084 1085backup_mode: 1086 at91_backup_mode 1087 1088exit_suspend: 1089 /* Exit the self-refresh mode */ 1090 at91_sramc_self_refresh_dis 1091 1092 /* Restore registers, and return */ 1093 ldmfd sp!, {r4 - r12, pc} 1094ENDPROC(at91_pm_suspend_in_sram) 1095 1096.pmc_base: 1097 .word 0 1098.sramc_base: 1099 .word 0 1100.sramc1_base: 1101 .word 0 1102.sramc_phy_base: 1103 .word 0 1104.shdwc: 1105 .word 0 1106.sfrbu: 1107 .word 0 1108.memtype: 1109 .word 0 1110.pm_mode: 1111 .word 0 1112.mckr_offset: 1113 .word 0 1114.pmc_version: 1115 .word 0 1116.saved_mckr: 1117 .word 0 1118.saved_pllar: 1119 .word 0 1120.saved_sam9_lpr: 1121 .word 0 1122.saved_sam9_lpr1: 1123 .word 0 1124.saved_sam9_mdr: 1125 .word 0 1126.saved_sam9_mdr1: 1127 .word 0 1128.saved_osc_status: 1129 .word 0 1130#ifdef CONFIG_SOC_SAMA7 1131.saved_mck1: 1132 .word 0 1133.saved_mck2: 1134 .word 0 1135.saved_mck3: 1136 .word 0 1137.saved_mck4: 1138 .word 0 1139#endif 1140 1141ENTRY(at91_pm_suspend_in_sram_sz) 1142 .word .-at91_pm_suspend_in_sram 1143