1// SPDX-License-Identifier: GPL-2.0-or-later 2/* 3 * Copyright 2011 ST-Ericsson AB 4 */ 5 6/dts-v1/; 7#include "ste-db9500.dtsi" 8#include "ste-href-ab8500.dtsi" 9#include "ste-href-family-pinctrl.dtsi" 10 11/ { 12 model = "Calao Systems Snowball platform with device tree"; 13 compatible = "calaosystems,snowball-a9500", "st-ericsson,u9500"; 14 15 memory { 16 device_type = "memory"; 17 reg = <0x00000000 0x20000000>; 18 }; 19 20 battery: battery { 21 compatible = "simple-battery"; 22 battery-type = "lithium-ion-polymer"; 23 }; 24 25 thermal-zones { 26 battery-thermal { 27 /* This zone will be polled by the battery temperature code */ 28 polling-delay = <0>; 29 polling-delay-passive = <0>; 30 thermal-sensors = <&bat_therm>; 31 32 trips { 33 battery-crit-hi { 34 temperature = <70000>; 35 hysteresis = <2000>; 36 type = "critical"; 37 }; 38 }; 39 }; 40 }; 41 42 bat_therm: thermistor { 43 compatible = "murata,ncp18wb473"; 44 io-channels = <&gpadc 0x02>; /* BatTemp */ 45 pullup-uv = <1800000>; 46 pullup-ohm = <230000>; 47 pulldown-ohm = <0>; 48 #thermal-sensor-cells = <0>; 49 }; 50 51 en_3v3_reg: en_3v3 { 52 compatible = "regulator-fixed"; 53 regulator-name = "en-3v3-fixed-supply"; 54 regulator-min-microvolt = <3300000>; 55 regulator-max-microvolt = <3300000>; 56 /* AB8500 GPIOs start from 1 - offset 25 is GPIO26. */ 57 gpio = <&ab8500_gpio 25 0x4>; 58 startup-delay-us = <5000>; 59 enable-active-high; 60 }; 61 62 gpio_keys { 63 compatible = "gpio-keys"; 64 #address-cells = <1>; 65 #size-cells = <0>; 66 67 button@1 { 68 debounce-interval = <50>; 69 wakeup-source; 70 linux,code = <2>; 71 label = "userpb"; 72 gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>; 73 }; 74 button@2 { 75 debounce-interval = <50>; 76 wakeup-source; 77 linux,code = <3>; 78 label = "extkb1"; 79 gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>; 80 }; 81 button@3 { 82 debounce-interval = <50>; 83 wakeup-source; 84 linux,code = <4>; 85 label = "extkb2"; 86 gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>; 87 }; 88 button@4 { 89 debounce-interval = <50>; 90 wakeup-source; 91 linux,code = <5>; 92 label = "extkb3"; 93 gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>; 94 }; 95 button@5 { 96 debounce-interval = <50>; 97 wakeup-source; 98 linux,code = <6>; 99 label = "extkb4"; 100 gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>; 101 }; 102 }; 103 104 leds { 105 compatible = "gpio-leds"; 106 pinctrl-names = "default"; 107 pinctrl-0 = <&gpioled_snowball_mode>; 108 used-led { 109 label = "user_led"; 110 gpios = <&gpio4 14 GPIO_ACTIVE_HIGH>; 111 default-state = "on"; 112 linux,default-trigger = "heartbeat"; 113 }; 114 }; 115 116 soc { 117 /* Name the GPIO muxed rails on the Snowball board */ 118 gpio@8012e000 { 119 /* GPIOs 0 - 31 */ 120 gpio-line-names = "", "", "", "", "", "", "", "", 121 "", "", "", "", "", "", "", "", 122 "", "", "", "", "", "", "", "", 123 "", "", "", "", "", "", "", 124 "AP_GPIO31"; 125 }; 126 127 gpio@8012e080 { 128 /* GPIOs 32 - 63 */ 129 gpio-line-names = "USR PB", "", "", "", "", "", "", "", 130 "", "", "", "", "", "", "", "", 131 "", "", "", "", "", "", "", "", 132 "", "", "", "", "", "", "", ""; 133 }; 134 135 gpio@8000e000 { 136 /* GPIOs 64 - 95 */ 137 gpio-line-names = "", "", "", "", "AP_GPIO68", "", "", "", 138 "", "", "", "", "", "", "", "", 139 "", "", "", "", "", "", "", "", 140 "", "", "", "", "", "", "", ""; 141 }; 142 143 gpio@8000e100 { 144 /* GPIOs 128 - 159 */ 145 gpio-line-names = "", "", "", "", "", "", "", "", 146 "", "", "", "", "IRQ_LAN", "RSTn_LAN", 147 "USR_LED", "", "", "", "", "", "", 148 "", "", "AP_GPIO151", "AP_GPIO152", 149 "", "", "", "", "", "", ""; 150 }; 151 152 gpio@8000e180 { 153 /* GPIOs 160 - 191 */ 154 gpio-line-names = "", "AP_GPIO161", "AP_GPIO162", 155 "ACCELEROMETER_INT1_RDY", 156 "ACCELEROMETER_INT2", "MAG_DRDY", 157 "GYRO_DRDY", "RSTn_MLC", "RSTn_SLC", 158 "GYRO_INT", "UART_WAKE", "GBF_RESET", 159 "", "", "", "", 160 "", "", "", "", "", "", "", "", 161 "", "", "", "", "", "", "", ""; 162 }; 163 164 gpio@8011e000 { 165 /* GPIOs 192 - 223 */ 166 gpio-line-names = "HDTV_INTn", "", "", "", "HDTV_RST", 167 "", "", "", "", "", "", "", "", "", 168 "", "", "", "", "", "", "", "", "", 169 "WLAN_RESETN", "WLAN_IRQ", "MMC_EN", 170 "MMC_CD", "", "", "", "", ""; 171 }; 172 173 gpio@8011e080 { 174 /* GPIOs 224 - 255 */ 175 gpio-line-names = "", "", "", "", "SD_SEL", "", "", "", 176 "", "", "", "", "", "", "", "", 177 "", "", "", "", "", "", "", "", 178 "", "", "", "", "", "", "", ""; 179 }; 180 181 msp0: msp@80123000 { 182 pinctrl-names = "default"; 183 pinctrl-0 = <&msp0txrxtfstck_a_1_default>; 184 status = "okay"; 185 }; 186 187 msp1: msp@80124000 { 188 pinctrl-names = "default"; 189 pinctrl-0 = <&msp1txrx_a_1_default>; 190 status = "okay"; 191 }; 192 193 msp2: msp@80117000 { 194 pinctrl-names = "default"; 195 pinctrl-0 = <&msp2_a_1_default>; 196 }; 197 198 msp3: msp@80125000 { 199 status = "okay"; 200 }; 201 202 external-bus@50000000 { 203 status = "okay"; 204 205 ethernet@0 { 206 compatible = "smsc,lan9115"; 207 reg = <0 0x10000>; 208 interrupts = <12 IRQ_TYPE_EDGE_RISING>; 209 interrupt-parent = <&gpio4>; 210 vdd33a-supply = <&en_3v3_reg>; 211 vddvario-supply = <&db8500_vape_reg>; 212 pinctrl-names = "default"; 213 pinctrl-0 = <ð_snowball_mode>; 214 215 reg-shift = <1>; 216 reg-io-width = <2>; 217 smsc,force-internal-phy; 218 smsc,irq-active-high; 219 smsc,irq-push-pull; 220 221 clocks = <&prcc_pclk 3 0>; 222 }; 223 }; 224 225 /* ST6G3244ME level translator for 1.8/2.9 V */ 226 vmmci: regulator-gpio { 227 compatible = "regulator-gpio"; 228 229 /* GPIO228 SD_SEL */ 230 gpios = <&gpio7 4 GPIO_ACTIVE_HIGH>; 231 /* GPIO217 MMC_EN */ 232 enable-gpio = <&gpio6 25 GPIO_ACTIVE_HIGH>; 233 enable-active-high; 234 235 regulator-min-microvolt = <1800000>; 236 regulator-max-microvolt = <2900000>; 237 regulator-name = "mmci-reg"; 238 regulator-type = "voltage"; 239 240 startup-delay-us = <100>; 241 242 states = <1800000 0x1 243 2900000 0x0>; 244 }; 245 246 // External Micro SD slot 247 mmc@80126000 { 248 arm,primecell-periphid = <0x10480180>; 249 max-frequency = <100000000>; 250 bus-width = <4>; 251 cap-sd-highspeed; 252 cap-mmc-highspeed; 253 sd-uhs-sdr12; 254 sd-uhs-sdr25; 255 /* All direction control is used */ 256 st,sig-dir-cmd; 257 st,sig-dir-dat0; 258 st,sig-dir-dat2; 259 st,sig-dir-dat31; 260 st,sig-pin-fbclk; 261 full-pwr-cycle; 262 vmmc-supply = <&ab8500_ldo_aux3_reg>; 263 vqmmc-supply = <&vmmci>; 264 pinctrl-names = "default", "sleep"; 265 pinctrl-0 = <&mc0_a_1_default &sdi0_default_mode>; 266 pinctrl-1 = <&mc0_a_1_sleep>; 267 268 /* GPIO218 MMC_CD */ 269 cd-gpios = <&gpio6 26 GPIO_ACTIVE_LOW>; 270 271 status = "okay"; 272 }; 273 274 // WLAN SDIO channel 275 mmc@80118000 { 276 arm,primecell-periphid = <0x10480180>; 277 max-frequency = <100000000>; 278 bus-width = <4>; 279 pinctrl-names = "default", "sleep"; 280 pinctrl-0 = <&mc1_a_1_default>; 281 pinctrl-1 = <&mc1_a_1_sleep>; 282 283 status = "okay"; 284 }; 285 286 // Unused PoP eMMC - register and put it to sleep by default */ 287 mmc@80005000 { 288 arm,primecell-periphid = <0x10480180>; 289 pinctrl-names = "default"; 290 pinctrl-0 = <&mc2_a_1_sleep>; 291 292 status = "okay"; 293 }; 294 295 // On-board eMMC 296 mmc@80114000 { 297 arm,primecell-periphid = <0x10480180>; 298 max-frequency = <100000000>; 299 bus-width = <8>; 300 cap-mmc-highspeed; 301 no-sdio; 302 no-sd; 303 vmmc-supply = <&ab8500_ldo_aux2_reg>; 304 pinctrl-names = "default", "sleep"; 305 pinctrl-0 = <&mc4_a_1_default>; 306 pinctrl-1 = <&mc4_a_1_sleep>; 307 308 status = "okay"; 309 }; 310 311 serial@80120000 { 312 pinctrl-names = "default", "sleep"; 313 pinctrl-0 = <&u0_a_1_default>; 314 pinctrl-1 = <&u0_a_1_sleep>; 315 status = "okay"; 316 }; 317 318 /* This UART is unused and thus left disabled */ 319 serial@80121000 { 320 pinctrl-names = "default", "sleep"; 321 pinctrl-0 = <&u1rxtx_a_1_default>; 322 pinctrl-1 = <&u1rxtx_a_1_sleep>; 323 }; 324 325 serial@80007000 { 326 pinctrl-names = "default", "sleep"; 327 pinctrl-0 = <&u2rxtx_c_1_default>; 328 pinctrl-1 = <&u2rxtx_c_1_sleep>; 329 status = "okay"; 330 }; 331 332 i2c@80004000 { 333 pinctrl-names = "default","sleep"; 334 pinctrl-0 = <&i2c0_a_1_default>; 335 pinctrl-1 = <&i2c0_a_1_sleep>; 336 status = "okay"; 337 }; 338 339 i2c@80122000 { 340 pinctrl-names = "default","sleep"; 341 pinctrl-0 = <&i2c1_b_2_default>; 342 pinctrl-1 = <&i2c1_b_2_sleep>; 343 status = "okay"; 344 }; 345 346 i2c@80128000 { 347 pinctrl-names = "default","sleep"; 348 pinctrl-0 = <&i2c2_b_2_default>; 349 pinctrl-1 = <&i2c2_b_2_sleep>; 350 status = "okay"; 351 lsm303dlh@18 { 352 /* Accelerometer */ 353 compatible = "st,lsm303dlh-accel"; 354 st,drdy-int-pin = <1>; 355 reg = <0x18>; 356 vdd-supply = <&ab8500_ldo_aux1_reg>; 357 vddio-supply = <&db8500_vsmps2_reg>; 358 pinctrl-names = "default"; 359 pinctrl-0 = <&accel_snowball_mode>; 360 interrupt-parent = <&gpio5>; 361 interrupts = <3 IRQ_TYPE_EDGE_RISING>, /* INT1 */ 362 <4 IRQ_TYPE_EDGE_RISING>; /* INT2 */ 363 }; 364 lsm303dlh@1e { 365 /* Magnetometer */ 366 compatible = "st,lsm303dlh-magn"; 367 reg = <0x1e>; 368 vdd-supply = <&ab8500_ldo_aux1_reg>; 369 vddio-supply = <&db8500_vsmps2_reg>; 370 pinctrl-names = "default"; 371 pinctrl-0 = <&magneto_snowball_mode>; 372 interrupt-parent = <&gpio5>; 373 interrupts = <5 IRQ_TYPE_EDGE_RISING>; /* DRDY line */ 374 }; 375 l3g4200d@68 { 376 /* Gyroscope */ 377 compatible = "st,l3g4200d-gyro"; 378 st,drdy-int-pin = <2>; 379 reg = <0x68>; 380 vdd-supply = <&ab8500_ldo_aux1_reg>; 381 vddio-supply = <&db8500_vsmps2_reg>; 382 pinctrl-names = "default"; 383 pinctrl-0 = <&gyro_snowball_mode>; 384 interrupt-parent = <&gpio5>; 385 interrupts = <6 IRQ_TYPE_EDGE_RISING>, /* DRDY line */ 386 <9 IRQ_TYPE_EDGE_RISING>; /* INT1 */ 387 }; 388 lsp001wm@5c { 389 /* Barometer/pressure sensor */ 390 compatible = "st,lps001wp-press"; 391 reg = <0x5c>; 392 vdd-supply = <&ab8500_ldo_aux1_reg>; 393 vddio-supply = <&db8500_vsmps2_reg>; 394 }; 395 }; 396 397 i2c@80110000 { 398 pinctrl-names = "default","sleep"; 399 pinctrl-0 = <&i2c3_c_2_default>; 400 pinctrl-1 = <&i2c3_c_2_sleep>; 401 status = "okay"; 402 }; 403 404 spi@80002000 { 405 pinctrl-names = "default"; 406 pinctrl-0 = <&ssp0_snowball_mode>; 407 status = "okay"; 408 }; 409 410 prcmu@80157000 { 411 ab8500 { 412 gpio { 413 /* 414 * AB8500 GPIOs are numbered starting from 1, so the first 415 * index 0 is what in the datasheet is called "GPIO1", and 416 * the second is "GPIO2" and so forth. Confusingly, the 417 * Snowball schematic then names the "GPIO2" line "PM_GPIO1". 418 * while later naming "GPIO4" as "PM_GPIO4". 419 */ 420 gpio-line-names = "", /* AB8500 GPIO1 */ 421 "PM_GPIO1", /* AB8500 GPIO2 */ 422 "WLAN_CLK_REQ", /* AB8500 GPIO3 */ 423 "PM_GPIO4", /* AB8500 GPIO4 */ 424 "", "", "", "", "", "", "", "", "", "", "", 425 "EN_3V6", /* AB8500 GPIO16 */ 426 "", "", "", "" ,"", "", "", "", "", 427 "EN_3V3", /* AB8500 GPIO26 */ 428 "", "", "", "", "", "", "", "", "", "", "", "", "", 429 "PM_GPIO40", /* AB8500 GPIO40 */ 430 "PM_GPIO41", /* AB8500 GPIO41 */ 431 "PM_GPIO42"; /* AB8500 GPIO42 */ 432 }; 433 434 phy { 435 pinctrl-names = "default", "sleep"; 436 pinctrl-0 = <&usb_a_1_default>; 437 pinctrl-1 = <&usb_a_1_sleep>; 438 }; 439 440 ext_regulators: regulator-external { 441 ab8500_ext1_reg: ab8500_ext1 { 442 regulator-name = "ab8500-ext-supply1"; 443 }; 444 445 ab8500_ext2_reg_reg: ab8500_ext2 { 446 regulator-name = "ab8500-ext-supply2"; 447 }; 448 449 ab8500_ext3_reg_reg: ab8500_ext3 { 450 regulator-name = "ab8500-ext-supply3"; 451 }; 452 }; 453 454 regulator { 455 ab8500_ldo_aux1_reg: ab8500_ldo_aux1 { 456 regulator-name = "V-DISPLAY"; 457 }; 458 459 ab8500_ldo_aux2_reg: ab8500_ldo_aux2 { 460 regulator-name = "V-eMMC1"; 461 }; 462 463 ab8500_ldo_aux3_reg: ab8500_ldo_aux3 { 464 regulator-name = "V-MMC-SD"; 465 }; 466 467 ab8500_ldo_intcore_reg: ab8500_ldo_intcore { 468 regulator-name = "V-INTCORE"; 469 }; 470 471 ab8500_ldo_tvout_reg: ab8500_ldo_tvout { 472 regulator-name = "V-TVOUT"; 473 }; 474 475 ab8500_ldo_audio_reg: ab8500_ldo_audio { 476 regulator-name = "V-AUD"; 477 }; 478 479 ab8500_ldo_anamic1_reg: ab8500_ldo_anamic1 { 480 regulator-name = "V-AMIC1"; 481 }; 482 483 ab8500_ldo_anamic2_reg: ab8500_ldo_anamic2 { 484 regulator-name = "V-AMIC2"; 485 }; 486 487 ab8500_ldo_dmic_reg: ab8500_ldo_dmic { 488 regulator-name = "V-DMIC"; 489 }; 490 491 ab8500_ldo_ana_reg: ab8500_ldo_ana { 492 regulator-name = "V-CSI/DSI"; 493 }; 494 }; 495 }; 496 }; 497 498 pinctrl { 499 /* 500 * Set this up using hogs, as time goes by and as seems fit, these 501 * can be moved over to being controlled by respective device. 502 */ 503 pinctrl-names = "default"; 504 pinctrl-0 = <&gbf_snowball_mode>, 505 <&wlan_snowball_mode>; 506 507 ethernet { 508 /* 509 * Mux in "SM" which is used for the 510 * SMSC911x Ethernet adapter 511 */ 512 eth_snowball_mode: eth_snowball { 513 snowball_mux { 514 function = "sm"; 515 groups = "sm_b_1"; 516 }; 517 /* LAN IRQ pin */ 518 snowball_cfg1 { 519 pins = "GPIO140_B11"; 520 ste,config = <&in_nopull>; 521 }; 522 /* LAN reset pin */ 523 snowball_cfg2 { 524 pins = "GPIO141_C12"; 525 ste,config = <&gpio_out_hi>; 526 }; 527 528 }; 529 }; 530 sdi0 { 531 sdi0_default_mode: sdi0_default { 532 snowball_mux { 533 function = "mc0"; 534 /* Add the DAT31 pin even if it is not really used */ 535 groups = "mc0dat31dir_a_1"; 536 }; 537 snowball_cfg1 { 538 pins = "GPIO21_AB3"; /* DAT31DIR */ 539 ste,config = <&out_hi>; 540 }; 541 /* SD card detect GPIO pin, extend default state */ 542 snowball_cfg2 { 543 pins = "GPIO218_AH11"; 544 ste,config = <&gpio_in_pu>; 545 }; 546 /* VMMCI level-shifter enable */ 547 snowball_cfg3 { 548 pins = "GPIO217_AH12"; 549 ste,config = <&gpio_out_hi>; 550 }; 551 /* VMMCI level-shifter voltage select */ 552 snowball_cfg4 { 553 pins = "GPIO228_AJ6"; 554 ste,config = <&gpio_out_hi>; 555 }; 556 }; 557 }; 558 ssp0 { 559 ssp0_snowball_mode: ssp0_snowball_default { 560 snowball_mux { 561 function = "ssp0"; 562 groups = "ssp0_a_1"; 563 }; 564 snowball_cfg1 { 565 pins = "GPIO144_B13"; /* FRM */ 566 ste,config = <&gpio_out_hi>; 567 }; 568 snowball_cfg2 { 569 pins = "GPIO145_C13"; /* RXD */ 570 ste,config = <&in_pd>; 571 }; 572 snowball_cfg3 { 573 pins = 574 "GPIO146_D13", /* TXD */ 575 "GPIO143_D12"; /* CLK */ 576 ste,config = <&out_lo>; 577 }; 578 579 }; 580 }; 581 gpio_led { 582 gpioled_snowball_mode: gpioled_default { 583 snowball_cfg1 { 584 pins = "GPIO142_C11"; 585 ste,config = <&gpio_out_hi>; 586 }; 587 588 }; 589 }; 590 accelerometer { 591 accel_snowball_mode: accel_snowball { 592 /* Accelerometer lines */ 593 snowball_cfg1 { 594 pins = 595 "GPIO163_C20", /* ACCEL_IRQ1 */ 596 "GPIO164_B21"; /* ACCEL_IRQ2 */ 597 ste,config = <&gpio_in_pu>; 598 }; 599 }; 600 }; 601 gyro { 602 gyro_snowball_mode: gyro_snowball { 603 snowball_cfg1 { 604 pins = 605 "GPIO166_A22", /* DRDY */ 606 "GPIO169_D22"; /* INT */ 607 ste,config = <&gpio_in_pu>; 608 }; 609 }; 610 }; 611 magnetometer { 612 magneto_snowball_mode: magneto_snowball { 613 snowball_cfg1 { 614 pins = "GPIO165_C21"; /* MAG_DRDY */ 615 ste,config = <&gpio_in_pu>; 616 }; 617 }; 618 }; 619 gbf { 620 gbf_snowball_mode: gbf_snowball { 621 /* 622 * GBF (GPS, Bluetooth, FM-radio) interface, 623 * pull low to reset state 624 */ 625 snowball_cfg1 { 626 pins = "GPIO171_D23"; /* GBF_ENA_RESET */ 627 ste,config = <&gpio_out_lo>; 628 }; 629 }; 630 }; 631 wlan { 632 wlan_snowball_mode: wlan_snowball { 633 /* 634 * Activate this mode with the WLAN chip. 635 * These are plain GPIO pins used by WLAN 636 */ 637 snowball_cfg1 { 638 pins = 639 "GPIO161_D21", /* WLAN_PMU_EN */ 640 "GPIO215_AH13"; /* WLAN_ENA */ 641 ste,config = <&gpio_out_lo>; 642 }; 643 snowball_cfg2 { 644 pins = "GPIO216_AG12"; /* WLAN_IRQ */ 645 ste,config = <&gpio_in_pu>; 646 }; 647 }; 648 }; 649 }; 650 651 mcde@a0350000 { 652 pinctrl-names = "default", "sleep"; 653 pinctrl-0 = <&lcd_default_mode>; 654 pinctrl-1 = <&lcd_sleep_mode>; 655 }; 656 }; 657}; 658