1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Device Tree Source for the Lager board
4 *
5 * Copyright (C) 2013-2014 Renesas Solutions Corp.
6 * Copyright (C) 2014 Cogent Embedded, Inc.
7 * Copyright (C) 2015-2016 Renesas Electronics Corporation
8 */
9
10/*
11 * SSI-AK4643
12 *
13 * SW1: 1: AK4643
14 *      2: CN22
15 *      3: ADV7511
16 *
17 * This command is required when Playback/Capture
18 *
19 *	amixer set "LINEOUT Mixer DACL" on
20 *	amixer set "DVC Out" 100%
21 *	amixer set "DVC In" 100%
22 *
23 * You can use Mute
24 *
25 *	amixer set "DVC Out Mute" on
26 *	amixer set "DVC In Mute" on
27 *
28 * You can use Volume Ramp
29 *
30 *	amixer set "DVC Out Ramp Up Rate"   "0.125 dB/64 steps"
31 *	amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
32 *	amixer set "DVC Out Ramp" on
33 *	aplay xxx.wav &
34 *	amixer set "DVC Out"  80%  // Volume Down
35 *	amixer set "DVC Out" 100%  // Volume Up
36 */
37
38/dts-v1/;
39#include "r8a7790.dtsi"
40#include <dt-bindings/gpio/gpio.h>
41#include <dt-bindings/input/input.h>
42
43/ {
44	model = "Lager";
45	compatible = "renesas,lager", "renesas,r8a7790";
46
47	aliases {
48		serial0 = &scif0;
49		serial1 = &scifa1;
50		i2c8 = &gpioi2c1;
51		i2c9 = &gpioi2c2;
52		i2c10 = &i2cexio0;
53		i2c11 = &i2cexio1;
54		i2c12 = &i2chdmi;
55		i2c13 = &i2cpwr;
56		mmc0 = &mmcif1;
57		mmc1 = &sdhi0;
58		mmc2 = &sdhi2;
59	};
60
61	chosen {
62		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
63		stdout-path = "serial0:115200n8";
64	};
65
66	memory@40000000 {
67		device_type = "memory";
68		reg = <0 0x40000000 0 0x40000000>;
69	};
70
71	memory@140000000 {
72		device_type = "memory";
73		reg = <1 0x40000000 0 0xc0000000>;
74	};
75
76	lbsc {
77		#address-cells = <1>;
78		#size-cells = <1>;
79	};
80
81	keyboard {
82		compatible = "gpio-keys";
83
84		pinctrl-0 = <&keyboard_pins>;
85		pinctrl-names = "default";
86
87		one {
88			linux,code = <KEY_1>;
89			label = "SW2-1";
90			wakeup-source;
91			debounce-interval = <20>;
92			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
93		};
94		two {
95			linux,code = <KEY_2>;
96			label = "SW2-2";
97			wakeup-source;
98			debounce-interval = <20>;
99			gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
100		};
101		three {
102			linux,code = <KEY_3>;
103			label = "SW2-3";
104			wakeup-source;
105			debounce-interval = <20>;
106			gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
107		};
108		four {
109			linux,code = <KEY_4>;
110			label = "SW2-4";
111			wakeup-source;
112			debounce-interval = <20>;
113			gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
114		};
115	};
116
117	leds {
118		compatible = "gpio-leds";
119		led6 {
120			gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
121		};
122		led7 {
123			gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
124		};
125		led8 {
126			gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>;
127		};
128	};
129
130	fixedregulator3v3: regulator-3v3 {
131		compatible = "regulator-fixed";
132		regulator-name = "fixed-3.3V";
133		regulator-min-microvolt = <3300000>;
134		regulator-max-microvolt = <3300000>;
135		regulator-boot-on;
136		regulator-always-on;
137	};
138
139	vcc_sdhi0: regulator-vcc-sdhi0 {
140		compatible = "regulator-fixed";
141
142		regulator-name = "SDHI0 Vcc";
143		regulator-min-microvolt = <3300000>;
144		regulator-max-microvolt = <3300000>;
145
146		gpio = <&gpio5 24 GPIO_ACTIVE_HIGH>;
147		enable-active-high;
148	};
149
150	vccq_sdhi0: regulator-vccq-sdhi0 {
151		compatible = "regulator-gpio";
152
153		regulator-name = "SDHI0 VccQ";
154		regulator-min-microvolt = <1800000>;
155		regulator-max-microvolt = <3300000>;
156
157		gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
158		gpios-states = <1>;
159		states = <3300000 1>, <1800000 0>;
160	};
161
162	vcc_sdhi2: regulator-vcc-sdhi2 {
163		compatible = "regulator-fixed";
164
165		regulator-name = "SDHI2 Vcc";
166		regulator-min-microvolt = <3300000>;
167		regulator-max-microvolt = <3300000>;
168
169		gpio = <&gpio5 25 GPIO_ACTIVE_HIGH>;
170		enable-active-high;
171	};
172
173	vccq_sdhi2: regulator-vccq-sdhi2 {
174		compatible = "regulator-gpio";
175
176		regulator-name = "SDHI2 VccQ";
177		regulator-min-microvolt = <1800000>;
178		regulator-max-microvolt = <3300000>;
179
180		gpios = <&gpio5 30 GPIO_ACTIVE_HIGH>;
181		gpios-states = <1>;
182		states = <3300000 1>, <1800000 0>;
183	};
184
185	audio_clock: audio_clock {
186		compatible = "fixed-clock";
187		#clock-cells = <0>;
188		clock-frequency = <11289600>;
189	};
190
191	rsnd_ak4643: sound {
192		compatible = "simple-audio-card";
193
194		simple-audio-card,format = "left_j";
195		simple-audio-card,bitclock-master = <&sndcodec>;
196		simple-audio-card,frame-master = <&sndcodec>;
197
198		sndcpu: simple-audio-card,cpu {
199			sound-dai = <&rcar_sound>;
200		};
201
202		sndcodec: simple-audio-card,codec {
203			sound-dai = <&ak4643>;
204			clocks = <&audio_clock>;
205		};
206	};
207
208	vga-encoder {
209		compatible = "adi,adv7123";
210
211		ports {
212			#address-cells = <1>;
213			#size-cells = <0>;
214
215			port@0 {
216				reg = <0>;
217				adv7123_in: endpoint {
218					remote-endpoint = <&du_out_rgb>;
219				};
220			};
221			port@1 {
222				reg = <1>;
223				adv7123_out: endpoint {
224					remote-endpoint = <&vga_in>;
225				};
226			};
227		};
228	};
229
230	vga {
231		compatible = "vga-connector";
232
233		port {
234			vga_in: endpoint {
235				remote-endpoint = <&adv7123_out>;
236			};
237		};
238	};
239
240	hdmi-in {
241		compatible = "hdmi-connector";
242		type = "a";
243
244		port {
245			hdmi_con_in: endpoint {
246				remote-endpoint = <&adv7612_in>;
247			};
248		};
249	};
250
251	cec_clock: cec-clock {
252		compatible = "fixed-clock";
253		#clock-cells = <0>;
254		clock-frequency = <12000000>;
255	};
256
257	hdmi-out {
258		compatible = "hdmi-connector";
259		type = "a";
260
261		port {
262			hdmi_con_out: endpoint {
263				remote-endpoint = <&adv7511_out>;
264			};
265		};
266	};
267
268	x2_clk: x2-clock {
269		compatible = "fixed-clock";
270		#clock-cells = <0>;
271		clock-frequency = <148500000>;
272	};
273
274	x13_clk: x13-clock {
275		compatible = "fixed-clock";
276		#clock-cells = <0>;
277		clock-frequency = <148500000>;
278	};
279
280	gpioi2c1: i2c-8 {
281		#address-cells = <1>;
282		#size-cells = <0>;
283		compatible = "i2c-gpio";
284		status = "disabled";
285		scl-gpios = <&gpio1 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
286		sda-gpios = <&gpio1 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
287		i2c-gpio,delay-us = <5>;
288	};
289
290	gpioi2c2: i2c-9 {
291		#address-cells = <1>;
292		#size-cells = <0>;
293		compatible = "i2c-gpio";
294		status = "disabled";
295		scl-gpios = <&gpio5 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
296		sda-gpios = <&gpio5 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
297		i2c-gpio,delay-us = <5>;
298	};
299
300	/*
301	 * IIC0/I2C0 is routed to EXIO connector A, pins 114 (SCL) + 116 (SDA) only.
302	 * We use the I2C demuxer, so the desired IP core can be selected at runtime
303	 * depending on the use case (e.g. DMA with IIC0 or slave support with I2C0).
304	 * Note: For testing the I2C slave feature, it is convenient to connect this
305	 * bus with IIC3 on pins 110 (SCL) + 112 (SDA), select I2C0 at runtime, and
306	 * instantiate the slave device at runtime according to the documentation.
307	 * You can then communicate with the slave via IIC3.
308	 *
309	 * IIC0/I2C0 does not appear to support fallback to GPIO.
310	 */
311	i2cexio0: i2c-10 {
312		compatible = "i2c-demux-pinctrl";
313		i2c-parent = <&iic0>, <&i2c0>;
314		i2c-bus-name = "i2c-exio0";
315		#address-cells = <1>;
316		#size-cells = <0>;
317	};
318
319	/*
320	 * IIC1/I2C1 is routed to EXIO connector A, pins 78 (SCL) + 80 (SDA).
321	 * This is similar to the arangement described for i2cexio0 (above)
322	 * with a fallback to GPIO also provided.
323	 */
324	i2cexio1: i2c-11 {
325		compatible = "i2c-demux-pinctrl";
326		i2c-parent = <&iic1>, <&i2c1>, <&gpioi2c1>;
327		i2c-bus-name = "i2c-exio1";
328		#address-cells = <1>;
329		#size-cells = <0>;
330	};
331
332	/*
333	 * IIC2 and I2C2 may be switched using pinmux.
334	 * A fallback to GPIO is also provided.
335	 */
336	i2chdmi: i2c-12 {
337		compatible = "i2c-demux-pinctrl";
338		i2c-parent = <&iic2>, <&i2c2>, <&gpioi2c2>;
339		i2c-bus-name = "i2c-hdmi";
340		#address-cells = <1>;
341		#size-cells = <0>;
342
343		ak4643: codec@12 {
344			compatible = "asahi-kasei,ak4643";
345			#sound-dai-cells = <0>;
346			reg = <0x12>;
347		};
348
349		composite-in@20 {
350			compatible = "adi,adv7180";
351			reg = <0x20>;
352
353			port {
354				adv7180: endpoint {
355					bus-width = <8>;
356					remote-endpoint = <&vin1ep0>;
357				};
358			};
359		};
360
361		hdmi@39 {
362			compatible = "adi,adv7511w";
363			reg = <0x39>;
364			interrupt-parent = <&gpio1>;
365			interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
366			clocks = <&cec_clock>;
367			clock-names = "cec";
368
369			adi,input-depth = <8>;
370			adi,input-colorspace = "rgb";
371			adi,input-clock = "1x";
372
373			ports {
374				#address-cells = <1>;
375				#size-cells = <0>;
376
377				port@0 {
378					reg = <0>;
379					adv7511_in: endpoint {
380						remote-endpoint = <&lvds0_out>;
381					};
382				};
383
384				port@1 {
385					reg = <1>;
386					adv7511_out: endpoint {
387						remote-endpoint = <&hdmi_con_out>;
388					};
389				};
390			};
391		};
392
393		hdmi-in@4c {
394			compatible = "adi,adv7612";
395			reg = <0x4c>;
396			interrupt-parent = <&gpio1>;
397			interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
398			default-input = <0>;
399
400			ports {
401				#address-cells = <1>;
402				#size-cells = <0>;
403
404				port@0 {
405					reg = <0>;
406					adv7612_in: endpoint {
407						remote-endpoint = <&hdmi_con_in>;
408					};
409				};
410
411				port@2 {
412					reg = <2>;
413					adv7612_out: endpoint {
414						remote-endpoint = <&vin0ep2>;
415					};
416				};
417			};
418		};
419	};
420
421	/*
422	 * IIC3 and I2C3 may be switched using pinmux.
423	 * IIC3/I2C3 does not appear to support fallback to GPIO.
424	 */
425	i2cpwr: i2c-13 {
426		compatible = "i2c-demux-pinctrl";
427		pinctrl-names = "default";
428		pinctrl-0 = <&pmic_irq_pins>;
429		i2c-parent = <&iic3>, <&i2c3>;
430		i2c-bus-name = "i2c-pwr";
431		#address-cells = <1>;
432		#size-cells = <0>;
433
434		pmic@58 {
435			compatible = "dlg,da9063";
436			reg = <0x58>;
437			interrupt-parent = <&irqc0>;
438			interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
439			interrupt-controller;
440
441			rtc {
442				compatible = "dlg,da9063-rtc";
443			};
444
445			watchdog {
446				compatible = "dlg,da9063-watchdog";
447			};
448		};
449
450		vdd_dvfs: regulator@68 {
451			compatible = "dlg,da9210";
452			reg = <0x68>;
453			interrupt-parent = <&irqc0>;
454			interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
455
456			regulator-min-microvolt = <1000000>;
457			regulator-max-microvolt = <1000000>;
458			regulator-boot-on;
459			regulator-always-on;
460		};
461	};
462};
463
464&du {
465	pinctrl-0 = <&du_pins>;
466	pinctrl-names = "default";
467	status = "okay";
468
469	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 722>,
470		 <&x13_clk>, <&x2_clk>;
471	clock-names = "du.0", "du.1", "du.2", "dclkin.0", "dclkin.1";
472
473	ports {
474		port@0 {
475			endpoint {
476				remote-endpoint = <&adv7123_in>;
477			};
478		};
479	};
480};
481
482&lvds0 {
483	status = "okay";
484
485	ports {
486		port@1 {
487			endpoint {
488				remote-endpoint = <&adv7511_in>;
489			};
490		};
491	};
492};
493
494&lvds1 {
495	ports {
496		port@1 {
497			lvds_connector: endpoint {
498			};
499		};
500	};
501};
502
503&extal_clk {
504	clock-frequency = <20000000>;
505};
506
507&pfc {
508	pinctrl-0 = <&scif_clk_pins>;
509	pinctrl-names = "default";
510
511	du_pins: du {
512		groups = "du_rgb666", "du_sync_1", "du_clk_out_0";
513		function = "du";
514	};
515
516	scif0_pins: scif0 {
517		groups = "scif0_data";
518		function = "scif0";
519	};
520
521	scif_clk_pins: scif_clk {
522		groups = "scif_clk";
523		function = "scif_clk";
524	};
525
526	ether_pins: ether {
527		groups = "eth_link", "eth_mdio", "eth_rmii";
528		function = "eth";
529	};
530
531	phy1_pins: phy1 {
532		groups = "intc_irq0";
533		function = "intc";
534	};
535
536	scifa1_pins: scifa1 {
537		groups = "scifa1_data";
538		function = "scifa1";
539	};
540
541	sdhi0_pins: sd0 {
542		groups = "sdhi0_data4", "sdhi0_ctrl";
543		function = "sdhi0";
544		power-source = <3300>;
545	};
546
547	sdhi0_pins_uhs: sd0_uhs {
548		groups = "sdhi0_data4", "sdhi0_ctrl";
549		function = "sdhi0";
550		power-source = <1800>;
551	};
552
553	sdhi2_pins: sd2 {
554		groups = "sdhi2_data4", "sdhi2_ctrl";
555		function = "sdhi2";
556		power-source = <3300>;
557	};
558
559	sdhi2_pins_uhs: sd2_uhs {
560		groups = "sdhi2_data4", "sdhi2_ctrl";
561		function = "sdhi2";
562		power-source = <1800>;
563	};
564
565	mmc1_pins: mmc1 {
566		groups = "mmc1_data8", "mmc1_ctrl";
567		function = "mmc1";
568	};
569
570	qspi_pins: qspi {
571		groups = "qspi_ctrl", "qspi_data4";
572		function = "qspi";
573	};
574
575	msiof1_pins: msiof1 {
576		groups = "msiof1_clk", "msiof1_sync", "msiof1_rx",
577				 "msiof1_tx";
578		function = "msiof1";
579	};
580
581	i2c0_pins: i2c0 {
582		groups = "i2c0";
583		function = "i2c0";
584	};
585
586	iic0_pins: iic0 {
587		groups = "iic0";
588		function = "iic0";
589	};
590
591	i2c1_pins: i2c1 {
592		groups = "i2c1";
593		function = "i2c1";
594	};
595
596	iic1_pins: iic1 {
597		groups = "iic1";
598		function = "iic1";
599	};
600
601	i2c2_pins: i2c2 {
602		groups = "i2c2";
603		function = "i2c2";
604	};
605
606	iic2_pins: iic2 {
607		groups = "iic2";
608		function = "iic2";
609	};
610
611	i2c3_pins: i2c3 {
612		groups = "i2c3";
613		function = "i2c3";
614	};
615
616	iic3_pins: iic3 {
617		groups = "iic3";
618		function = "iic3";
619	};
620
621	pmic_irq_pins: pmicirq {
622		groups = "intc_irq2";
623		function = "intc";
624	};
625
626	hsusb_pins: hsusb {
627		groups = "usb0_ovc_vbus";
628		function = "usb0";
629	};
630
631	usb0_pins: usb0 {
632		groups = "usb0";
633		function = "usb0";
634	};
635
636	usb1_pins: usb1 {
637		groups = "usb1";
638		function = "usb1";
639	};
640
641	usb2_pins: usb2 {
642		groups = "usb2";
643		function = "usb2";
644	};
645
646	vin0_pins: vin0 {
647		groups = "vin0_data24", "vin0_sync", "vin0_clkenb", "vin0_clk";
648		function = "vin0";
649	};
650
651	vin1_pins: vin1 {
652		groups = "vin1_data8", "vin1_clk";
653		function = "vin1";
654	};
655
656	sound_pins: sound {
657		groups = "ssi0129_ctrl", "ssi0_data", "ssi1_data";
658		function = "ssi";
659	};
660
661	sound_clk_pins: sound_clk {
662		groups = "audio_clk_a";
663		function = "audio_clk";
664	};
665
666	keyboard_pins: keyboard {
667		pins = "GP_1_14", "GP_1_24", "GP_1_26", "GP_1_28";
668		bias-pull-up;
669	};
670};
671
672&ether {
673	pinctrl-0 = <&ether_pins>, <&phy1_pins>;
674	pinctrl-names = "default";
675
676	phy-handle = <&phy1>;
677	renesas,ether-link-active-low;
678	status = "okay";
679
680	phy1: ethernet-phy@1 {
681		compatible = "ethernet-phy-id0022.1537",
682			     "ethernet-phy-ieee802.3-c22";
683		reg = <1>;
684		interrupt-parent = <&irqc0>;
685		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
686		micrel,led-mode = <1>;
687		reset-gpios = <&gpio5 31 GPIO_ACTIVE_LOW>;
688	};
689};
690
691&cmt0 {
692	status = "okay";
693};
694
695&mmcif1 {
696	pinctrl-0 = <&mmc1_pins>;
697	pinctrl-names = "default";
698
699	vmmc-supply = <&fixedregulator3v3>;
700	bus-width = <8>;
701	non-removable;
702	status = "okay";
703};
704
705&sata1 {
706	status = "okay";
707};
708
709&qspi {
710	pinctrl-0 = <&qspi_pins>;
711	pinctrl-names = "default";
712
713	status = "okay";
714
715	flash: flash@0 {
716		compatible = "spansion,s25fl512s", "jedec,spi-nor";
717		reg = <0>;
718		spi-max-frequency = <30000000>;
719		spi-tx-bus-width = <4>;
720		spi-rx-bus-width = <4>;
721		spi-cpha;
722		spi-cpol;
723		m25p,fast-read;
724
725		partitions {
726			compatible = "fixed-partitions";
727			#address-cells = <1>;
728			#size-cells = <1>;
729
730			partition@0 {
731				label = "loader";
732				reg = <0x00000000 0x00040000>;
733				read-only;
734			};
735			partition@40000 {
736				label = "user";
737				reg = <0x00040000 0x00400000>;
738				read-only;
739			};
740			partition@440000 {
741				label = "flash";
742				reg = <0x00440000 0x03bc0000>;
743			};
744		};
745	};
746};
747
748&scif0 {
749	pinctrl-0 = <&scif0_pins>;
750	pinctrl-names = "default";
751
752	status = "okay";
753};
754
755&scifa1 {
756	pinctrl-0 = <&scifa1_pins>;
757	pinctrl-names = "default";
758
759	status = "okay";
760};
761
762&scif_clk {
763	clock-frequency = <14745600>;
764};
765
766&msiof1 {
767	pinctrl-0 = <&msiof1_pins>;
768	pinctrl-names = "default";
769
770	status = "okay";
771
772	pmic: pmic@0 {
773		compatible = "renesas,r2a11302ft";
774		reg = <0>;
775		spi-max-frequency = <6000000>;
776		spi-cpol;
777		spi-cpha;
778	};
779};
780
781&sdhi0 {
782	pinctrl-0 = <&sdhi0_pins>;
783	pinctrl-1 = <&sdhi0_pins_uhs>;
784	pinctrl-names = "default", "state_uhs";
785
786	vmmc-supply = <&vcc_sdhi0>;
787	vqmmc-supply = <&vccq_sdhi0>;
788	cd-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
789	sd-uhs-sdr50;
790	sd-uhs-sdr104;
791	status = "okay";
792};
793
794&sdhi2 {
795	pinctrl-0 = <&sdhi2_pins>;
796	pinctrl-1 = <&sdhi2_pins_uhs>;
797	pinctrl-names = "default", "state_uhs";
798
799	vmmc-supply = <&vcc_sdhi2>;
800	vqmmc-supply = <&vccq_sdhi2>;
801	cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>;
802	sd-uhs-sdr50;
803	status = "okay";
804};
805
806&cpu0 {
807	cpu0-supply = <&vdd_dvfs>;
808};
809
810&i2c0	{
811	pinctrl-0 = <&i2c0_pins>;
812	pinctrl-names = "i2c-exio0";
813};
814
815&iic0	{
816	pinctrl-0 = <&iic0_pins>;
817	pinctrl-names = "i2c-exio0";
818};
819
820&i2c1	{
821	pinctrl-0 = <&i2c1_pins>;
822	pinctrl-names = "i2c-exio1";
823};
824
825&iic1	{
826	pinctrl-0 = <&iic1_pins>;
827	pinctrl-names = "i2c-exio1";
828};
829
830&i2c2	{
831	pinctrl-0 = <&i2c2_pins>;
832	pinctrl-names = "i2c-hdmi";
833
834	clock-frequency = <100000>;
835};
836
837&iic2	{
838	pinctrl-0 = <&iic2_pins>;
839	pinctrl-names = "i2c-hdmi";
840
841	clock-frequency = <100000>;
842};
843
844&i2c3	{
845	pinctrl-0 = <&i2c3_pins>;
846	pinctrl-names = "i2c-pwr";
847};
848
849&iic3	{
850	pinctrl-0 = <&iic3_pins>;
851	pinctrl-names = "i2c-pwr";
852};
853
854&pci0 {
855	status = "okay";
856	pinctrl-0 = <&usb0_pins>;
857	pinctrl-names = "default";
858};
859
860&pci1 {
861	status = "okay";
862	pinctrl-0 = <&usb1_pins>;
863	pinctrl-names = "default";
864};
865
866&xhci {
867	status = "okay";
868	pinctrl-0 = <&usb2_pins>;
869	pinctrl-names = "default";
870};
871
872&pci2 {
873	status = "okay";
874	pinctrl-0 = <&usb2_pins>;
875	pinctrl-names = "default";
876};
877
878&hsusb {
879	status = "okay";
880	pinctrl-0 = <&hsusb_pins>;
881	pinctrl-names = "default";
882	renesas,enable-gpio = <&gpio5 18 GPIO_ACTIVE_HIGH>;
883};
884
885&usbphy {
886	status = "okay";
887};
888
889/* HDMI video input */
890&vin0 {
891	pinctrl-0 = <&vin0_pins>;
892	pinctrl-names = "default";
893
894	status = "okay";
895
896	port {
897		vin0ep2: endpoint {
898			remote-endpoint = <&adv7612_out>;
899			bus-width = <24>;
900			hsync-active = <0>;
901			vsync-active = <0>;
902			pclk-sample = <1>;
903			data-active = <1>;
904		};
905	};
906};
907
908/* composite video input */
909&vin1 {
910	pinctrl-0 = <&vin1_pins>;
911	pinctrl-names = "default";
912
913	status = "okay";
914
915	port {
916		vin1ep0: endpoint {
917			remote-endpoint = <&adv7180>;
918			bus-width = <8>;
919		};
920	};
921};
922
923&rcar_sound {
924	pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
925	pinctrl-names = "default";
926
927	/* Single DAI */
928	#sound-dai-cells = <0>;
929
930	status = "okay";
931
932	rcar_sound,dai {
933		dai0 {
934			playback = <&ssi0>, <&src2>, <&dvc0>;
935			capture  = <&ssi1>, <&src3>, <&dvc1>;
936		};
937	};
938};
939
940&rwdt {
941	timeout-sec = <60>;
942	status = "okay";
943};
944
945&ssi1 {
946	shared-pin;
947};
948