1// SPDX-License-Identifier: GPL-2.0
2#include "qcom-msm8974pro.dtsi"
3#include "qcom-pm8841.dtsi"
4#include "qcom-pm8941.dtsi"
5#include <dt-bindings/input/input.h>
6#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
7
8/ {
9	model = "OnePlus One";
10	compatible = "oneplus,bacon", "qcom,msm8974pro", "qcom,msm8974";
11	chassis-type = "handset";
12	qcom,msm-id = <194 0x10000>;
13	qcom,board-id = <8 0>;
14
15	aliases {
16		serial0 = &blsp1_uart2;
17	};
18
19	chosen {
20		stdout-path = "serial0:115200n8";
21	};
22
23	gpio-keys {
24		compatible = "gpio-keys";
25
26		pinctrl-0 = <&gpio_keys_default>, <&gpio_hall_sensor_default>;
27		pinctrl-names = "default";
28
29		key-volume-down {
30			label = "Volume Down";
31			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
32			linux,code = <KEY_VOLUMEDOWN>;
33			wakeup-source;
34			debounce-interval = <15>;
35		};
36
37		key-volume-up {
38			label = "Volume Up";
39			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
40			linux,code = <KEY_VOLUMEUP>;
41			wakeup-source;
42			debounce-interval = <15>;
43		};
44
45		event-hall-sensor {
46			label = "Hall Effect Sensor";
47			gpios = <&tlmm 68 GPIO_ACTIVE_LOW>;
48			linux,input-type = <EV_SW>;
49			linux,code = <SW_LID>;
50			linux,can-disable;
51			debounce-interval = <150>;
52		};
53	};
54};
55
56&blsp1_i2c1 {
57	status = "okay";
58
59	fuel-gauge@55 {
60		compatible = "ti,bq27541";
61		reg = <0x55>;
62		power-supplies = <&bq24196_charger>;
63	};
64};
65
66&blsp1_i2c2 {
67	status = "okay";
68
69	rmi4-i2c-dev@20 {
70		compatible = "syna,rmi4-i2c";
71		reg = <0x20>;
72
73		syna,startup-delay-ms = <100>;
74
75		interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>;
76		vdd-supply = <&pm8941_l22>;
77		vio-supply = <&pm8941_lvs3>;
78
79		pinctrl-names = "default";
80		pinctrl-0 = <&touch_default_state>;
81
82		#address-cells = <1>;
83		#size-cells = <0>;
84
85		rmi4-f01@1 {
86			reg = <0x1>;
87			syna,nosleep-mode = <1>;
88		};
89
90		rmi4-f12@12 {
91			reg = <0x12>;
92			syna,sensor-type = <1>;
93			/*
94			 * Touchscreen size is 2040x1080, y-values between
95			 * 1920-2040 are used for touchkey (menu, home & back).
96			 * For now clip it off so we don't get touch events
97			 * outside of the display area.
98			 */
99			syna,clip-y-high = <1920>;
100		};
101	};
102
103	led-controller@36 {
104		compatible = "ti,lm3630a";
105		reg = <0x36>;
106
107		#address-cells = <1>;
108		#size-cells = <0>;
109
110		led@0 {
111			reg = <0>;
112			led-sources = <0 1>;
113			label = "lcd-backlight";
114			default-brightness = <80>;
115		};
116	};
117
118	led-controller@68 {
119		compatible = "si-en,sn3193";
120		reg = <0x68>;
121
122		shutdown-gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
123
124		#address-cells = <1>;
125		#size-cells = <0>;
126
127		led@1 {
128			reg = <1>;
129			label = "red:status";
130			led-max-microamp = <17500>;
131		};
132
133		led@2 {
134			reg = <2>;
135			label = "green:status";
136			led-max-microamp = <17500>;
137		};
138
139		led@3 {
140			reg = <3>;
141			label = "blue:status";
142			led-max-microamp = <17500>;
143		};
144	};
145};
146
147&blsp1_i2c6 {
148	status = "okay";
149
150	bq24196_charger: charger@6b {
151		compatible = "ti,bq24196";
152		reg = <0x6b>;
153		interrupts-extended = <&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
154		omit-battery-class;
155	};
156};
157
158&blsp1_uart2 {
159	status = "okay";
160};
161
162&gcc {
163	compatible = "qcom,gcc-msm8974pro-ac";
164};
165
166&pm8941_coincell {
167	qcom,rset-ohms = <800>;
168	qcom,vset-millivolts = <3200>;
169
170	status = "okay";
171};
172
173&pm8941_gpios {
174	gpio_keys_default: gpio-keys-active-state {
175		pins = "gpio2", "gpio5";
176		function = "normal";
177		input-enable;
178		bias-disable;
179		power-source = <PM8941_GPIO_S3>;
180	};
181};
182
183&pm8941_vib {
184	status = "okay";
185};
186
187&pronto {
188	vddmx-supply = <&pm8841_s1>;
189	vddcx-supply = <&pm8841_s2>;
190	vddpx-supply = <&pm8941_s3>;
191
192	pinctrl-names = "default";
193	pinctrl-0 = <&wcnss_pin_a>;
194
195	status = "okay";
196
197	iris {
198		vddxo-supply = <&pm8941_l6>;
199		vddrfa-supply = <&pm8941_l11>;
200		vddpa-supply = <&pm8941_l19>;
201		vdddig-supply = <&pm8941_s3>;
202	};
203
204	smd-edge {
205		qcom,remote-pid = <4>;
206		label = "pronto";
207
208		wcnss {
209			status = "okay";
210		};
211	};
212};
213
214&remoteproc_adsp {
215	cx-supply = <&pm8841_s2>;
216
217	status = "okay";
218};
219
220&rpm_requests {
221	regulators-0 {
222		compatible = "qcom,rpm-pm8841-regulators";
223
224		pm8841_s1: s1 {
225			regulator-min-microvolt = <675000>;
226			regulator-max-microvolt = <1050000>;
227		};
228
229		pm8841_s2: s2 {
230			regulator-min-microvolt = <875000>;
231			regulator-max-microvolt = <1050000>;
232			regulator-always-on;
233		};
234
235		pm8841_s3: s3 {
236			regulator-min-microvolt = <1050000>;
237			regulator-max-microvolt = <1050000>;
238		};
239	};
240
241	regulators-1 {
242		compatible = "qcom,rpm-pm8941-regulators";
243
244		vdd_l1_l3-supply = <&pm8941_s1>;
245		vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
246		vdd_l4_l11-supply = <&pm8941_s1>;
247		vdd_l5_l7-supply = <&pm8941_s2>;
248		vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
249		vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>;
250		vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
251		vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
252		vdd_l21-supply = <&vreg_boost>;
253
254		pm8941_s1: s1 {
255			regulator-min-microvolt = <1300000>;
256			regulator-max-microvolt = <1300000>;
257
258			regulator-always-on;
259			regulator-boot-on;
260		};
261
262		pm8941_s2: s2 {
263			regulator-min-microvolt = <2150000>;
264			regulator-max-microvolt = <2150000>;
265
266			regulator-boot-on;
267		};
268
269		pm8941_s3: s3 {
270			regulator-min-microvolt = <1800000>;
271			regulator-max-microvolt = <1800000>;
272			regulator-system-load = <154000>;
273
274			regulator-always-on;
275			regulator-boot-on;
276			regulator-allow-set-load;
277		};
278
279		pm8941_l1: l1 {
280			regulator-min-microvolt = <1225000>;
281			regulator-max-microvolt = <1225000>;
282
283			regulator-always-on;
284			regulator-boot-on;
285		};
286
287		pm8941_l2: l2 {
288			regulator-min-microvolt = <1200000>;
289			regulator-max-microvolt = <1200000>;
290		};
291
292		pm8941_l3: l3 {
293			regulator-min-microvolt = <1225000>;
294			regulator-max-microvolt = <1225000>;
295		};
296
297		pm8941_l4: l4 {
298			regulator-min-microvolt = <1225000>;
299			regulator-max-microvolt = <1225000>;
300		};
301
302		pm8941_l5: l5 {
303			regulator-min-microvolt = <1800000>;
304			regulator-max-microvolt = <1800000>;
305		};
306
307		pm8941_l6: l6 {
308			regulator-min-microvolt = <1800000>;
309			regulator-max-microvolt = <1800000>;
310
311			regulator-boot-on;
312		};
313
314		pm8941_l7: l7 {
315			regulator-min-microvolt = <1800000>;
316			regulator-max-microvolt = <1800000>;
317
318			regulator-boot-on;
319		};
320
321		pm8941_l8: l8 {
322			regulator-min-microvolt = <1800000>;
323			regulator-max-microvolt = <1800000>;
324		};
325
326		pm8941_l9: l9 {
327			regulator-min-microvolt = <1800000>;
328			regulator-max-microvolt = <2950000>;
329		};
330
331		pm8941_l10: l10 {
332			regulator-min-microvolt = <1800000>;
333			regulator-max-microvolt = <2950000>;
334		};
335
336		pm8941_l11: l11 {
337			regulator-min-microvolt = <1225000>;
338			regulator-max-microvolt = <1350000>;
339		};
340
341		pm8941_l12: l12 {
342			regulator-min-microvolt = <1800000>;
343			regulator-max-microvolt = <1800000>;
344
345			regulator-always-on;
346			regulator-boot-on;
347			regulator-allow-set-load;
348		};
349
350		pm8941_l13: l13 {
351			regulator-min-microvolt = <1800000>;
352			regulator-max-microvolt = <2950000>;
353
354			regulator-boot-on;
355		};
356
357		pm8941_l14: l14 {
358			regulator-min-microvolt = <1800000>;
359			regulator-max-microvolt = <1800000>;
360		};
361
362		pm8941_l15: l15 {
363			regulator-min-microvolt = <2050000>;
364			regulator-max-microvolt = <2050000>;
365		};
366
367		pm8941_l16: l16 {
368			regulator-min-microvolt = <2700000>;
369			regulator-max-microvolt = <2700000>;
370		};
371
372		pm8941_l17: l17 {
373			regulator-min-microvolt = <2850000>;
374			regulator-max-microvolt = <2850000>;
375		};
376
377		pm8941_l18: l18 {
378			regulator-min-microvolt = <2850000>;
379			regulator-max-microvolt = <2850000>;
380		};
381
382		pm8941_l19: l19 {
383			regulator-min-microvolt = <2900000>;
384			regulator-max-microvolt = <3350000>;
385		};
386
387		pm8941_l20: l20 {
388			regulator-min-microvolt = <2950000>;
389			regulator-max-microvolt = <2950000>;
390
391			regulator-system-load = <200000>;
392			regulator-allow-set-load;
393			regulator-boot-on;
394		};
395
396		pm8941_l21: l21 {
397			regulator-min-microvolt = <2950000>;
398			regulator-max-microvolt = <2950000>;
399
400			regulator-boot-on;
401		};
402
403		pm8941_l22: l22 {
404			regulator-min-microvolt = <3000000>;
405			regulator-max-microvolt = <3000000>;
406			regulator-allow-set-load;
407		};
408
409		pm8941_l23: l23 {
410			regulator-min-microvolt = <3000000>;
411			regulator-max-microvolt = <3000000>;
412		};
413
414		pm8941_l24: l24 {
415			regulator-min-microvolt = <3075000>;
416			regulator-max-microvolt = <3075000>;
417
418			regulator-boot-on;
419		};
420
421		pm8941_lvs3: lvs3 {};
422	};
423};
424
425&sdhc_1 {
426	vmmc-supply = <&pm8941_l20>;
427	vqmmc-supply = <&pm8941_s3>;
428
429	pinctrl-names = "default", "sleep";
430	pinctrl-0 = <&sdc1_on>;
431	pinctrl-1 = <&sdc1_off>;
432
433	status = "okay";
434};
435
436&tlmm {
437	gpio_hall_sensor_default: gpio-hall-sensor-default-state {
438		pins = "gpio68";
439		function = "gpio";
440		drive-strength = <8>;
441		bias-pull-up;
442	};
443
444	sdc1_on: sdc1-on-state {
445		clk-pins {
446			pins = "sdc1_clk";
447			drive-strength = <4>;
448			bias-disable;
449		};
450
451		cmd-data-pins {
452			pins = "sdc1_cmd", "sdc1_data";
453			drive-strength = <4>;
454			bias-pull-up;
455		};
456	};
457
458	touch_default_state: touch-default-state {
459		int-pins {
460			pins = "gpio61";
461			function = "gpio";
462			drive-strength = <2>;
463			bias-disable;
464		};
465
466		reset-pins {
467			pins = "gpio60";
468			function = "gpio";
469			drive-strength = <2>;
470			bias-pull-up;
471		};
472	};
473
474	wcnss_pin_a: wcnss-pin-active-state {
475		wlan-pins {
476			pins = "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
477			function = "wlan";
478			drive-strength = <6>;
479			bias-pull-down;
480		};
481
482		bt-pins {
483			pins = "gpio35", "gpio43", "gpio44";
484			function = "bt";
485			drive-strength = <2>;
486			bias-pull-down;
487		};
488	};
489};
490
491&usb {
492	phys = <&usb_hs1_phy>;
493	phy-select = <&tcsr 0xb000 0>;
494	extcon = <&smbb>, <&usb_id>;
495	vbus-supply = <&chg_otg>;
496
497	hnp-disable;
498	srp-disable;
499	adp-disable;
500
501	status = "okay";
502};
503
504&usb_hs1_phy {
505	status = "okay";
506
507	v1p8-supply = <&pm8941_l6>;
508	v3p3-supply = <&pm8941_l24>;
509
510	extcon = <&smbb>;
511	qcom,init-seq = /bits/ 8 <0x1 0x64>;
512};
513