1// SPDX-License-Identifier: BSD-3-Clause 2#include <dt-bindings/iio/qcom,spmi-vadc.h> 3#include <dt-bindings/input/linux-event-codes.h> 4#include <dt-bindings/interrupt-controller/irq.h> 5#include <dt-bindings/spmi/spmi.h> 6 7/ { 8 thermal-zones { 9 pm8226-thermal { 10 polling-delay-passive = <100>; 11 polling-delay = <0>; 12 thermal-sensors = <&pm8226_temp>; 13 14 trips { 15 trip0 { 16 temperature = <105000>; 17 hysteresis = <2000>; 18 type = "passive"; 19 }; 20 21 trip1 { 22 temperature = <125000>; 23 hysteresis = <2000>; 24 type = "hot"; 25 }; 26 27 crit { 28 temperature = <145000>; 29 hysteresis = <2000>; 30 type = "critical"; 31 }; 32 }; 33 }; 34 }; 35}; 36 37&spmi_bus { 38 pm8226_0: pm8226@0 { 39 compatible = "qcom,pm8226", "qcom,spmi-pmic"; 40 reg = <0x0 SPMI_USID>; 41 #address-cells = <1>; 42 #size-cells = <0>; 43 44 pon@800 { 45 compatible = "qcom,pm8916-pon"; 46 reg = <0x800>; 47 48 pwrkey { 49 compatible = "qcom,pm8941-pwrkey"; 50 interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; 51 debounce = <15625>; 52 bias-pull-up; 53 linux,code = <KEY_POWER>; 54 }; 55 56 pm8226_resin: resin { 57 compatible = "qcom,pm8941-resin"; 58 interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; 59 debounce = <15625>; 60 bias-pull-up; 61 status = "disabled"; 62 }; 63 }; 64 65 smbb: charger@1000 { 66 compatible = "qcom,pm8226-charger"; 67 reg = <0x1000>; 68 interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>, 69 <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>, 70 <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>, 71 <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>, 72 <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>, 73 <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>, 74 <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>, 75 <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>; 76 interrupt-names = "chg-done", 77 "chg-fast", 78 "chg-trkl", 79 "bat-temp-ok", 80 "bat-present", 81 "chg-gone", 82 "usb-valid", 83 "dc-valid"; 84 85 chg_otg: otg-vbus { }; 86 }; 87 88 pm8226_temp: temp-alarm@2400 { 89 compatible = "qcom,spmi-temp-alarm"; 90 reg = <0x2400>; 91 interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>; 92 io-channels = <&pm8226_vadc VADC_DIE_TEMP>; 93 io-channel-names = "thermal"; 94 #thermal-sensor-cells = <0>; 95 }; 96 97 pm8226_vadc: adc@3100 { 98 compatible = "qcom,spmi-vadc"; 99 reg = <0x3100>; 100 interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; 101 #address-cells = <1>; 102 #size-cells = <0>; 103 #io-channel-cells = <1>; 104 105 channel@7 { 106 reg = <VADC_VSYS>; 107 qcom,pre-scaling = <1 3>; 108 label = "vph_pwr"; 109 }; 110 channel@8 { 111 reg = <VADC_DIE_TEMP>; 112 label = "die_temp"; 113 }; 114 channel@9 { 115 reg = <VADC_REF_625MV>; 116 label = "ref_625mv"; 117 }; 118 channel@a { 119 reg = <VADC_REF_1250MV>; 120 label = "ref_1250mv"; 121 }; 122 channel@e { 123 reg = <VADC_GND_REF>; 124 }; 125 channel@f { 126 reg = <VADC_VDD_VADC>; 127 }; 128 }; 129 130 pm8226_iadc: adc@3600 { 131 compatible = "qcom,pm8226-iadc", "qcom,spmi-iadc"; 132 reg = <0x3600>; 133 interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>; 134 }; 135 136 rtc@6000 { 137 compatible = "qcom,pm8941-rtc"; 138 reg = <0x6000>, <0x6100>; 139 reg-names = "rtc", "alarm"; 140 interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; 141 }; 142 143 pm8226_mpps: mpps@a000 { 144 compatible = "qcom,pm8226-mpp", "qcom,spmi-mpp"; 145 reg = <0xa000>; 146 gpio-controller; 147 #gpio-cells = <2>; 148 gpio-ranges = <&pm8226_mpps 0 0 8>; 149 interrupt-controller; 150 #interrupt-cells = <2>; 151 }; 152 153 pm8226_gpios: gpio@c000 { 154 compatible = "qcom,pm8226-gpio", "qcom,spmi-gpio"; 155 reg = <0xc000>; 156 gpio-controller; 157 #gpio-cells = <2>; 158 gpio-ranges = <&pm8226_gpios 0 0 8>; 159 interrupt-controller; 160 #interrupt-cells = <2>; 161 }; 162 }; 163 164 pm8226_1: pm8226@1 { 165 compatible = "qcom,pm8226", "qcom,spmi-pmic"; 166 reg = <0x1 SPMI_USID>; 167 #address-cells = <1>; 168 #size-cells = <0>; 169 170 pm8226_spmi_regulators: regulators { 171 compatible = "qcom,pm8226-regulators"; 172 }; 173 174 pm8226_vib: vibrator@c000 { 175 compatible = "qcom,pm8916-vib"; 176 reg = <0xc000>; 177 status = "disabled"; 178 }; 179 }; 180}; 181