1// SPDX-License-Identifier: ISC
2/*
3 * Device Tree file for Iomega NAS 100D
4 */
5
6/dts-v1/;
7
8#include "intel-ixp42x.dtsi"
9#include <dt-bindings/input/input.h>
10
11/ {
12	model = "Iomega NAS 100D";
13	compatible = "iom,nas-100d", "intel,ixp42x";
14	#address-cells = <1>;
15	#size-cells = <1>;
16
17	memory@0 {
18		/* 64 MB SDRAM */
19		device_type = "memory";
20		reg = <0x00000000 0x4000000>;
21	};
22
23	chosen {
24		bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait";
25		stdout-path = "uart0:115200n8";
26	};
27
28	aliases {
29		serial0 = &uart0;
30	};
31
32	leds {
33		compatible = "gpio-leds";
34		led-wlan {
35			label = "nas100d:red:wlan";
36			gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
37			default-state = "on";
38			/* We don't have WLAN trigger in the kernel (yet) */
39			linux,default-trigger = "netdev";
40		};
41		led-disk {
42			label = "nas100d:red:disk";
43			gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>;
44			default-state = "on";
45			linux,default-trigger = "disk-activity";
46		};
47		led-power {
48			label = "nas100d:red:power";
49			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
50			default-state = "on";
51			linux,default-trigger = "heartbeat";
52		};
53	};
54
55	gpio_keys {
56		compatible = "gpio-keys";
57
58		button-power {
59			wakeup-source;
60			linux,code = <KEY_POWER>;
61			label = "power";
62			gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
63		};
64		button-reset {
65			wakeup-source;
66			linux,code = <KEY_ESC>;
67			label = "reset";
68			gpios = <&gpio0 4 GPIO_ACTIVE_LOW>;
69		};
70	};
71
72	i2c {
73		compatible = "i2c-gpio";
74		sda-gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
75		scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
76		#address-cells = <1>;
77		#size-cells = <0>;
78
79		rtc@51 {
80			compatible = "nxp,pcf8563";
81			reg = <0x51>;
82		};
83	};
84
85	gpio-poweroff {
86		compatible = "gpio-poweroff";
87		gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
88		timeout-ms = <5000>;
89	};
90
91	soc {
92		bus@c4000000 {
93			/* The first 16MB region at CS0 on the expansion bus */
94			flash@0,0 {
95				compatible = "intel,ixp4xx-flash", "cfi-flash";
96				bank-width = <2>;
97				/*
98				 * 8 MB of Flash in 0x20000 byte blocks
99				 * mapped in at CS0.
100				 */
101				reg = <0 0x00000000 0x800000>;
102
103				partitions {
104					compatible = "redboot-fis";
105					/* Eraseblock at 0x7e0000 */
106					fis-index-block = <0x3f>;
107				};
108			};
109		};
110
111		pci@c0000000 {
112			status = "okay";
113
114			/*
115			 * Taken from NAS 100D PCI boardfile (nas100d-pci.c)
116			 * We have slots (IDSEL) 1, 2 and 3 and pins 1, 2 and 3.
117			 */
118			#interrupt-cells = <1>;
119			interrupt-map-mask = <0xf800 0 0 7>;
120			interrupt-map =
121			/* IDSEL 1 */
122			<0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */
123			/* IDSEL 2 */
124			<0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */
125			/* IDSEL 3 */
126			<0x1800 0 0 1 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */
127			<0x1800 0 0 2 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 8 */
128			<0x1800 0 0 3 &gpio0 7  IRQ_TYPE_LEVEL_LOW>; /* INT C on slot 3 is irq 7 */
129		};
130
131		ethernet@c8009000 {
132			status = "okay";
133			queue-rx = <&qmgr 3>;
134			queue-txready = <&qmgr 20>;
135			phy-mode = "rgmii";
136			phy-handle = <&phy0>;
137
138			mdio {
139				#address-cells = <1>;
140				#size-cells = <0>;
141
142				phy0: ethernet-phy@0 {
143					reg = <0>;
144				};
145			};
146		};
147	};
148};
149