1// SPDX-License-Identifier: ISC
2/*
3 * Device Tree file for ADI Engineering Coyote platform.
4 * Derived from boardfiles written by MontaVista software.
5 * Ethernet set-up from OpenWrt.
6 */
7
8/dts-v1/;
9
10#include "intel-ixp42x.dtsi"
11#include <dt-bindings/input/input.h>
12
13/ {
14	model = "ADI Engineering Coyote reference design";
15	compatible = "adieng,coyote", "intel,ixp42x";
16	#address-cells = <1>;
17	#size-cells = <1>;
18
19	memory@0 {
20		/* CHECKME: 16 MB SDRAM minimum, maybe the Coyote actually has more */
21		device_type = "memory";
22		reg = <0x00000000 0x01000000>;
23	};
24
25	chosen {
26		bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait";
27		stdout-path = "uart1:115200n8";
28	};
29
30	aliases {
31		/* These are switched around */
32		serial0 = &uart1;
33		serial1 = &uart0;
34	};
35
36	soc {
37		bus@c4000000 {
38			flash@0,0 {
39				compatible = "intel,ixp4xx-flash", "cfi-flash";
40				bank-width = <2>;
41				/*
42				 * 32 MB of Flash in 128 0x20000 sized blocks
43				 * mapped in at CS0 and CS1
44				 */
45				reg = <0 0x00000000 0x2000000>;
46
47				/* Configure expansion bus to allow writes */
48				intel,ixp4xx-eb-write-enable = <1>;
49
50				partitions {
51					compatible = "redboot-fis";
52					/* CHECKME: guess this is Redboot FIS */
53					fis-index-block = <0x1ff>;
54				};
55			};
56		};
57
58		pci@c0000000 {
59			status = "okay";
60
61			/*
62			 * Taken from Coyote PCI boardfile.
63			 * We have slots (IDSEL) 1 and 2 with one assigned IRQ
64			 * each handling all IRQs.
65			 */
66			#interrupt-cells = <1>;
67			interrupt-map-mask = <0xf800 0 0 7>;
68			interrupt-map =
69			/* IDSEL 1 */
70			<0x0800 0 0 1 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 6 */
71			<0x0800 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 6 */
72			<0x0800 0 0 3 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 6 */
73			<0x0800 0 0 4 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 6 */
74			/* IDSEL 2 */
75			<0x1000 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 11 */
76			<0x1000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 11 */
77			<0x1000 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 11 */
78			<0x1000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 2 is irq 11 */
79		};
80
81		/* EthB */
82		ethernet@c8009000 {
83			status = "okay";
84			queue-rx = <&qmgr 3>;
85			queue-txready = <&qmgr 20>;
86			phy-mode = "rgmii";
87			phy-handle = <&phy5>;
88
89			mdio {
90				#address-cells = <1>;
91				#size-cells = <0>;
92
93				phy4: ethernet-phy@4 {
94					reg = <4>;
95				};
96
97				phy5: ethernet-phy@5 {
98					reg = <5>;
99				};
100			};
101		};
102
103		/* EthC */
104		ethernet@c800a000 {
105			status = "okay";
106			queue-rx = <&qmgr 4>;
107			queue-txready = <&qmgr 21>;
108			phy-mode = "rgmii";
109			phy-handle = <&phy4>;
110		};
111	};
112};
113