1// SPDX-License-Identifier: GPL-2.0 2#include "bcm283x.dtsi" 3 4#include <dt-bindings/interrupt-controller/arm-gic.h> 5#include <dt-bindings/soc/bcm2835-pm.h> 6 7/ { 8 compatible = "brcm,bcm2711"; 9 10 #address-cells = <2>; 11 #size-cells = <1>; 12 13 interrupt-parent = <&gicv2>; 14 15 vc4: gpu { 16 compatible = "brcm,bcm2711-vc5"; 17 status = "disabled"; 18 }; 19 20 clk_27MHz: clk-27M { 21 #clock-cells = <0>; 22 compatible = "fixed-clock"; 23 clock-frequency = <27000000>; 24 clock-output-names = "27MHz-clock"; 25 }; 26 27 clk_108MHz: clk-108M { 28 #clock-cells = <0>; 29 compatible = "fixed-clock"; 30 clock-frequency = <108000000>; 31 clock-output-names = "108MHz-clock"; 32 }; 33 34 soc { 35 /* 36 * Defined ranges: 37 * Common BCM283x peripherals 38 * BCM2711-specific peripherals 39 * ARM-local peripherals 40 */ 41 ranges = <0x7e000000 0x0 0xfe000000 0x01800000>, 42 <0x7c000000 0x0 0xfc000000 0x02000000>, 43 <0x40000000 0x0 0xff800000 0x00800000>; 44 /* Emulate a contiguous 30-bit address range for DMA */ 45 dma-ranges = <0xc0000000 0x0 0x00000000 0x40000000>; 46 47 /* 48 * This node is the provider for the enable-method for 49 * bringing up secondary cores. 50 */ 51 local_intc: interrupt-controller@40000000 { 52 compatible = "brcm,bcm2836-l1-intc"; 53 reg = <0x40000000 0x100>; 54 }; 55 56 gicv2: interrupt-controller@40041000 { 57 interrupt-controller; 58 #interrupt-cells = <3>; 59 compatible = "arm,gic-400"; 60 reg = <0x40041000 0x1000>, 61 <0x40042000 0x2000>, 62 <0x40044000 0x2000>, 63 <0x40046000 0x2000>; 64 interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | 65 IRQ_TYPE_LEVEL_HIGH)>; 66 }; 67 68 avs_monitor: avs-monitor@7d5d2000 { 69 compatible = "brcm,bcm2711-avs-monitor", 70 "syscon", "simple-mfd"; 71 reg = <0x7d5d2000 0xf00>; 72 73 thermal: thermal { 74 compatible = "brcm,bcm2711-thermal"; 75 #thermal-sensor-cells = <0>; 76 }; 77 }; 78 79 dma: dma@7e007000 { 80 compatible = "brcm,bcm2835-dma"; 81 reg = <0x7e007000 0xb00>; 82 interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>, 83 <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>, 84 <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>, 85 <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>, 86 <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>, 87 <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>, 88 <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>, 89 /* DMA lite 7 - 10 */ 90 <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, 91 <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, 92 <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>, 93 <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; 94 interrupt-names = "dma0", 95 "dma1", 96 "dma2", 97 "dma3", 98 "dma4", 99 "dma5", 100 "dma6", 101 "dma7", 102 "dma8", 103 "dma9", 104 "dma10"; 105 #dma-cells = <1>; 106 brcm,dma-channel-mask = <0x07f5>; 107 }; 108 109 pm: watchdog@7e100000 { 110 compatible = "brcm,bcm2711-pm", "brcm,bcm2835-pm-wdt"; 111 #power-domain-cells = <1>; 112 #reset-cells = <1>; 113 reg = <0x7e100000 0x114>, 114 <0x7e00a000 0x24>, 115 <0x7ec11000 0x20>; 116 reg-names = "pm", "asb", "rpivid_asb"; 117 clocks = <&clocks BCM2835_CLOCK_V3D>, 118 <&clocks BCM2835_CLOCK_PERI_IMAGE>, 119 <&clocks BCM2835_CLOCK_H264>, 120 <&clocks BCM2835_CLOCK_ISP>; 121 clock-names = "v3d", "peri_image", "h264", "isp"; 122 system-power-controller; 123 }; 124 125 rng@7e104000 { 126 compatible = "brcm,bcm2711-rng200"; 127 reg = <0x7e104000 0x28>; 128 }; 129 130 uart2: serial@7e201400 { 131 compatible = "arm,pl011", "arm,primecell"; 132 reg = <0x7e201400 0x200>; 133 interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; 134 clocks = <&clocks BCM2835_CLOCK_UART>, 135 <&clocks BCM2835_CLOCK_VPU>; 136 clock-names = "uartclk", "apb_pclk"; 137 arm,primecell-periphid = <0x00241011>; 138 status = "disabled"; 139 }; 140 141 uart3: serial@7e201600 { 142 compatible = "arm,pl011", "arm,primecell"; 143 reg = <0x7e201600 0x200>; 144 interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; 145 clocks = <&clocks BCM2835_CLOCK_UART>, 146 <&clocks BCM2835_CLOCK_VPU>; 147 clock-names = "uartclk", "apb_pclk"; 148 arm,primecell-periphid = <0x00241011>; 149 status = "disabled"; 150 }; 151 152 uart4: serial@7e201800 { 153 compatible = "arm,pl011", "arm,primecell"; 154 reg = <0x7e201800 0x200>; 155 interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; 156 clocks = <&clocks BCM2835_CLOCK_UART>, 157 <&clocks BCM2835_CLOCK_VPU>; 158 clock-names = "uartclk", "apb_pclk"; 159 arm,primecell-periphid = <0x00241011>; 160 status = "disabled"; 161 }; 162 163 uart5: serial@7e201a00 { 164 compatible = "arm,pl011", "arm,primecell"; 165 reg = <0x7e201a00 0x200>; 166 interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; 167 clocks = <&clocks BCM2835_CLOCK_UART>, 168 <&clocks BCM2835_CLOCK_VPU>; 169 clock-names = "uartclk", "apb_pclk"; 170 arm,primecell-periphid = <0x00241011>; 171 status = "disabled"; 172 }; 173 174 spi3: spi@7e204600 { 175 compatible = "brcm,bcm2835-spi"; 176 reg = <0x7e204600 0x0200>; 177 interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; 178 clocks = <&clocks BCM2835_CLOCK_VPU>; 179 #address-cells = <1>; 180 #size-cells = <0>; 181 status = "disabled"; 182 }; 183 184 spi4: spi@7e204800 { 185 compatible = "brcm,bcm2835-spi"; 186 reg = <0x7e204800 0x0200>; 187 interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; 188 clocks = <&clocks BCM2835_CLOCK_VPU>; 189 #address-cells = <1>; 190 #size-cells = <0>; 191 status = "disabled"; 192 }; 193 194 spi5: spi@7e204a00 { 195 compatible = "brcm,bcm2835-spi"; 196 reg = <0x7e204a00 0x0200>; 197 interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; 198 clocks = <&clocks BCM2835_CLOCK_VPU>; 199 #address-cells = <1>; 200 #size-cells = <0>; 201 status = "disabled"; 202 }; 203 204 spi6: spi@7e204c00 { 205 compatible = "brcm,bcm2835-spi"; 206 reg = <0x7e204c00 0x0200>; 207 interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; 208 clocks = <&clocks BCM2835_CLOCK_VPU>; 209 #address-cells = <1>; 210 #size-cells = <0>; 211 status = "disabled"; 212 }; 213 214 i2c3: i2c@7e205600 { 215 compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; 216 reg = <0x7e205600 0x200>; 217 interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; 218 clocks = <&clocks BCM2835_CLOCK_VPU>; 219 #address-cells = <1>; 220 #size-cells = <0>; 221 status = "disabled"; 222 }; 223 224 i2c4: i2c@7e205800 { 225 compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; 226 reg = <0x7e205800 0x200>; 227 interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; 228 clocks = <&clocks BCM2835_CLOCK_VPU>; 229 #address-cells = <1>; 230 #size-cells = <0>; 231 status = "disabled"; 232 }; 233 234 i2c5: i2c@7e205a00 { 235 compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; 236 reg = <0x7e205a00 0x200>; 237 interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; 238 clocks = <&clocks BCM2835_CLOCK_VPU>; 239 #address-cells = <1>; 240 #size-cells = <0>; 241 status = "disabled"; 242 }; 243 244 i2c6: i2c@7e205c00 { 245 compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; 246 reg = <0x7e205c00 0x200>; 247 interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; 248 clocks = <&clocks BCM2835_CLOCK_VPU>; 249 #address-cells = <1>; 250 #size-cells = <0>; 251 status = "disabled"; 252 }; 253 254 pixelvalve0: pixelvalve@7e206000 { 255 compatible = "brcm,bcm2711-pixelvalve0"; 256 reg = <0x7e206000 0x100>; 257 interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; 258 status = "disabled"; 259 }; 260 261 pixelvalve1: pixelvalve@7e207000 { 262 compatible = "brcm,bcm2711-pixelvalve1"; 263 reg = <0x7e207000 0x100>; 264 interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; 265 status = "disabled"; 266 }; 267 268 pixelvalve2: pixelvalve@7e20a000 { 269 compatible = "brcm,bcm2711-pixelvalve2"; 270 reg = <0x7e20a000 0x100>; 271 interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; 272 status = "disabled"; 273 }; 274 275 pwm1: pwm@7e20c800 { 276 compatible = "brcm,bcm2835-pwm"; 277 reg = <0x7e20c800 0x28>; 278 clocks = <&clocks BCM2835_CLOCK_PWM>; 279 assigned-clocks = <&clocks BCM2835_CLOCK_PWM>; 280 assigned-clock-rates = <10000000>; 281 #pwm-cells = <2>; 282 status = "disabled"; 283 }; 284 285 pixelvalve4: pixelvalve@7e216000 { 286 compatible = "brcm,bcm2711-pixelvalve4"; 287 reg = <0x7e216000 0x100>; 288 interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; 289 status = "disabled"; 290 }; 291 292 hvs: hvs@7e400000 { 293 compatible = "brcm,bcm2711-hvs"; 294 reg = <0x7e400000 0x8000>; 295 interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; 296 }; 297 298 pixelvalve3: pixelvalve@7ec12000 { 299 compatible = "brcm,bcm2711-pixelvalve3"; 300 reg = <0x7ec12000 0x100>; 301 interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; 302 status = "disabled"; 303 }; 304 305 vec: vec@7ec13000 { 306 compatible = "brcm,bcm2711-vec"; 307 reg = <0x7ec13000 0x1000>; 308 clocks = <&clocks BCM2835_CLOCK_VEC>; 309 interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; 310 status = "disabled"; 311 }; 312 313 dvp: clock@7ef00000 { 314 compatible = "brcm,brcm2711-dvp"; 315 reg = <0x7ef00000 0x10>; 316 clocks = <&clk_108MHz>; 317 #clock-cells = <1>; 318 #reset-cells = <1>; 319 }; 320 321 aon_intr: interrupt-controller@7ef00100 { 322 compatible = "brcm,bcm2711-l2-intc", "brcm,l2-intc"; 323 reg = <0x7ef00100 0x30>; 324 interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; 325 interrupt-controller; 326 #interrupt-cells = <1>; 327 }; 328 329 hdmi0: hdmi@7ef00700 { 330 compatible = "brcm,bcm2711-hdmi0"; 331 reg = <0x7ef00700 0x300>, 332 <0x7ef00300 0x200>, 333 <0x7ef00f00 0x80>, 334 <0x7ef00f80 0x80>, 335 <0x7ef01b00 0x200>, 336 <0x7ef01f00 0x400>, 337 <0x7ef00200 0x80>, 338 <0x7ef04300 0x100>, 339 <0x7ef20000 0x100>; 340 reg-names = "hdmi", 341 "dvp", 342 "phy", 343 "rm", 344 "packet", 345 "metadata", 346 "csc", 347 "cec", 348 "hd"; 349 clock-names = "hdmi", "bvb", "audio", "cec"; 350 resets = <&dvp 0>; 351 interrupt-parent = <&aon_intr>; 352 interrupts = <0>, <1>, <2>, 353 <3>, <4>, <5>; 354 interrupt-names = "cec-tx", "cec-rx", "cec-low", 355 "wakeup", "hpd-connected", "hpd-removed"; 356 ddc = <&ddc0>; 357 dmas = <&dma 10>; 358 dma-names = "audio-rx"; 359 status = "disabled"; 360 }; 361 362 ddc0: i2c@7ef04500 { 363 compatible = "brcm,bcm2711-hdmi-i2c"; 364 reg = <0x7ef04500 0x100>, <0x7ef00b00 0x300>; 365 reg-names = "bsc", "auto-i2c"; 366 clock-frequency = <97500>; 367 status = "disabled"; 368 }; 369 370 hdmi1: hdmi@7ef05700 { 371 compatible = "brcm,bcm2711-hdmi1"; 372 reg = <0x7ef05700 0x300>, 373 <0x7ef05300 0x200>, 374 <0x7ef05f00 0x80>, 375 <0x7ef05f80 0x80>, 376 <0x7ef06b00 0x200>, 377 <0x7ef06f00 0x400>, 378 <0x7ef00280 0x80>, 379 <0x7ef09300 0x100>, 380 <0x7ef20000 0x100>; 381 reg-names = "hdmi", 382 "dvp", 383 "phy", 384 "rm", 385 "packet", 386 "metadata", 387 "csc", 388 "cec", 389 "hd"; 390 ddc = <&ddc1>; 391 clock-names = "hdmi", "bvb", "audio", "cec"; 392 resets = <&dvp 1>; 393 interrupt-parent = <&aon_intr>; 394 interrupts = <8>, <7>, <6>, 395 <9>, <10>, <11>; 396 interrupt-names = "cec-tx", "cec-rx", "cec-low", 397 "wakeup", "hpd-connected", "hpd-removed"; 398 dmas = <&dma 17>; 399 dma-names = "audio-rx"; 400 status = "disabled"; 401 }; 402 403 ddc1: i2c@7ef09500 { 404 compatible = "brcm,bcm2711-hdmi-i2c"; 405 reg = <0x7ef09500 0x100>, <0x7ef05b00 0x300>; 406 reg-names = "bsc", "auto-i2c"; 407 clock-frequency = <97500>; 408 status = "disabled"; 409 }; 410 }; 411 412 /* 413 * emmc2 has different DMA constraints based on SoC revisions. It was 414 * moved into its own bus, so as for RPi4's firmware to update them. 415 * The firmware will find whether the emmc2bus alias is defined, and if 416 * so, it'll edit the dma-ranges property below accordingly. 417 */ 418 emmc2bus: emmc2bus { 419 compatible = "simple-bus"; 420 #address-cells = <2>; 421 #size-cells = <1>; 422 423 ranges = <0x0 0x7e000000 0x0 0xfe000000 0x01800000>; 424 dma-ranges = <0x0 0xc0000000 0x0 0x00000000 0x40000000>; 425 426 emmc2: mmc@7e340000 { 427 compatible = "brcm,bcm2711-emmc2"; 428 reg = <0x0 0x7e340000 0x100>; 429 interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; 430 clocks = <&clocks BCM2711_CLOCK_EMMC2>; 431 status = "disabled"; 432 }; 433 }; 434 435 arm-pmu { 436 compatible = "arm,cortex-a72-pmu", "arm,armv8-pmuv3"; 437 interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>, 438 <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>, 439 <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>, 440 <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; 441 interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; 442 }; 443 444 timer { 445 compatible = "arm,armv8-timer"; 446 interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | 447 IRQ_TYPE_LEVEL_LOW)>, 448 <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | 449 IRQ_TYPE_LEVEL_LOW)>, 450 <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | 451 IRQ_TYPE_LEVEL_LOW)>, 452 <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | 453 IRQ_TYPE_LEVEL_LOW)>; 454 /* This only applies to the ARMv7 stub */ 455 arm,cpu-registers-not-fw-configured; 456 }; 457 458 cpus: cpus { 459 #address-cells = <1>; 460 #size-cells = <0>; 461 enable-method = "brcm,bcm2836-smp"; // for ARM 32-bit 462 463 /* Source for d/i-cache-line-size and d/i-cache-sets 464 * https://developer.arm.com/documentation/100095/0003 465 * /Level-1-Memory-System/About-the-L1-memory-system?lang=en 466 * Source for d/i-cache-size 467 * https://www.raspberrypi.com/documentation/computers 468 * /processors.html#bcm2711 469 */ 470 cpu0: cpu@0 { 471 device_type = "cpu"; 472 compatible = "arm,cortex-a72"; 473 reg = <0>; 474 enable-method = "spin-table"; 475 cpu-release-addr = <0x0 0x000000d8>; 476 d-cache-size = <0x8000>; 477 d-cache-line-size = <64>; 478 d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set 479 i-cache-size = <0xc000>; 480 i-cache-line-size = <64>; 481 i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set 482 next-level-cache = <&l2>; 483 }; 484 485 cpu1: cpu@1 { 486 device_type = "cpu"; 487 compatible = "arm,cortex-a72"; 488 reg = <1>; 489 enable-method = "spin-table"; 490 cpu-release-addr = <0x0 0x000000e0>; 491 d-cache-size = <0x8000>; 492 d-cache-line-size = <64>; 493 d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set 494 i-cache-size = <0xc000>; 495 i-cache-line-size = <64>; 496 i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set 497 next-level-cache = <&l2>; 498 }; 499 500 cpu2: cpu@2 { 501 device_type = "cpu"; 502 compatible = "arm,cortex-a72"; 503 reg = <2>; 504 enable-method = "spin-table"; 505 cpu-release-addr = <0x0 0x000000e8>; 506 d-cache-size = <0x8000>; 507 d-cache-line-size = <64>; 508 d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set 509 i-cache-size = <0xc000>; 510 i-cache-line-size = <64>; 511 i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set 512 next-level-cache = <&l2>; 513 }; 514 515 cpu3: cpu@3 { 516 device_type = "cpu"; 517 compatible = "arm,cortex-a72"; 518 reg = <3>; 519 enable-method = "spin-table"; 520 cpu-release-addr = <0x0 0x000000f0>; 521 d-cache-size = <0x8000>; 522 d-cache-line-size = <64>; 523 d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set 524 i-cache-size = <0xc000>; 525 i-cache-line-size = <64>; 526 i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set 527 next-level-cache = <&l2>; 528 }; 529 530 /* Source for d/i-cache-line-size and d/i-cache-sets 531 * https://developer.arm.com/documentation/100095/0003 532 * /Level-2-Memory-System/About-the-L2-memory-system?lang=en 533 * Source for d/i-cache-size 534 * https://www.raspberrypi.com/documentation/computers 535 * /processors.html#bcm2711 536 */ 537 l2: l2-cache0 { 538 compatible = "cache"; 539 cache-unified; 540 cache-size = <0x100000>; 541 cache-line-size = <64>; 542 cache-sets = <1024>; // 1MiB(size)/64(line-size)=16384ways/16-way set 543 cache-level = <2>; 544 }; 545 }; 546 547 scb { 548 compatible = "simple-bus"; 549 #address-cells = <2>; 550 #size-cells = <1>; 551 552 ranges = <0x0 0x7c000000 0x0 0xfc000000 0x03800000>, 553 <0x6 0x00000000 0x6 0x00000000 0x40000000>; 554 555 pcie0: pcie@7d500000 { 556 compatible = "brcm,bcm2711-pcie"; 557 reg = <0x0 0x7d500000 0x9310>; 558 device_type = "pci"; 559 #address-cells = <3>; 560 #interrupt-cells = <1>; 561 #size-cells = <2>; 562 interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>, 563 <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>; 564 interrupt-names = "pcie", "msi"; 565 interrupt-map-mask = <0x0 0x0 0x0 0x7>; 566 interrupt-map = <0 0 0 1 &gicv2 GIC_SPI 143 567 IRQ_TYPE_LEVEL_HIGH>, 568 <0 0 0 2 &gicv2 GIC_SPI 144 569 IRQ_TYPE_LEVEL_HIGH>, 570 <0 0 0 3 &gicv2 GIC_SPI 145 571 IRQ_TYPE_LEVEL_HIGH>, 572 <0 0 0 4 &gicv2 GIC_SPI 146 573 IRQ_TYPE_LEVEL_HIGH>; 574 msi-controller; 575 msi-parent = <&pcie0>; 576 577 ranges = <0x02000000 0x0 0xf8000000 0x6 0x00000000 578 0x0 0x04000000>; 579 /* 580 * The wrapper around the PCIe block has a bug 581 * preventing it from accessing beyond the first 3GB of 582 * memory. 583 */ 584 dma-ranges = <0x02000000 0x0 0x00000000 0x0 0x00000000 585 0x0 0xc0000000>; 586 brcm,enable-ssc; 587 }; 588 589 genet: ethernet@7d580000 { 590 compatible = "brcm,bcm2711-genet-v5"; 591 reg = <0x0 0x7d580000 0x10000>; 592 #address-cells = <0x1>; 593 #size-cells = <0x1>; 594 interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>, 595 <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>; 596 status = "disabled"; 597 598 genet_mdio: mdio@e14 { 599 compatible = "brcm,genet-mdio-v5"; 600 reg = <0xe14 0x8>; 601 reg-names = "mdio"; 602 #address-cells = <0x1>; 603 #size-cells = <0x0>; 604 }; 605 }; 606 607 v3d: gpu@7ec00000 { 608 compatible = "brcm,2711-v3d"; 609 reg = <0x0 0x7ec00000 0x4000>, 610 <0x0 0x7ec04000 0x4000>; 611 reg-names = "hub", "core0"; 612 613 power-domains = <&pm BCM2835_POWER_DOMAIN_GRAFX_V3D>; 614 resets = <&pm BCM2835_RESET_V3D>; 615 interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; 616 }; 617 }; 618}; 619 620&clk_osc { 621 clock-frequency = <54000000>; 622}; 623 624&clocks { 625 compatible = "brcm,bcm2711-cprman"; 626}; 627 628&cpu_thermal { 629 coefficients = <(-487) 410040>; 630 thermal-sensors = <&thermal>; 631}; 632 633&dsi0 { 634 interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; 635}; 636 637&dsi1 { 638 interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; 639 compatible = "brcm,bcm2711-dsi1"; 640}; 641 642&gpio { 643 compatible = "brcm,bcm2711-gpio"; 644 interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>, 645 <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>, 646 <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>, 647 <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; 648 649 gpio-ranges = <&gpio 0 0 58>; 650 651 gpclk0_gpio49: gpclk0-gpio49 { 652 pin-gpclk { 653 pins = "gpio49"; 654 function = "alt1"; 655 bias-disable; 656 }; 657 }; 658 gpclk1_gpio50: gpclk1-gpio50 { 659 pin-gpclk { 660 pins = "gpio50"; 661 function = "alt1"; 662 bias-disable; 663 }; 664 }; 665 gpclk2_gpio51: gpclk2-gpio51 { 666 pin-gpclk { 667 pins = "gpio51"; 668 function = "alt1"; 669 bias-disable; 670 }; 671 }; 672 673 i2c0_gpio46: i2c0-gpio46 { 674 pin-sda { 675 function = "alt0"; 676 pins = "gpio46"; 677 bias-pull-up; 678 }; 679 pin-scl { 680 function = "alt0"; 681 pins = "gpio47"; 682 bias-disable; 683 }; 684 }; 685 i2c1_gpio46: i2c1-gpio46 { 686 pin-sda { 687 function = "alt1"; 688 pins = "gpio46"; 689 bias-pull-up; 690 }; 691 pin-scl { 692 function = "alt1"; 693 pins = "gpio47"; 694 bias-disable; 695 }; 696 }; 697 i2c3_gpio2: i2c3-gpio2 { 698 pin-sda { 699 function = "alt5"; 700 pins = "gpio2"; 701 bias-pull-up; 702 }; 703 pin-scl { 704 function = "alt5"; 705 pins = "gpio3"; 706 bias-disable; 707 }; 708 }; 709 i2c3_gpio4: i2c3-gpio4 { 710 pin-sda { 711 function = "alt5"; 712 pins = "gpio4"; 713 bias-pull-up; 714 }; 715 pin-scl { 716 function = "alt5"; 717 pins = "gpio5"; 718 bias-disable; 719 }; 720 }; 721 i2c4_gpio6: i2c4-gpio6 { 722 pin-sda { 723 function = "alt5"; 724 pins = "gpio6"; 725 bias-pull-up; 726 }; 727 pin-scl { 728 function = "alt5"; 729 pins = "gpio7"; 730 bias-disable; 731 }; 732 }; 733 i2c4_gpio8: i2c4-gpio8 { 734 pin-sda { 735 function = "alt5"; 736 pins = "gpio8"; 737 bias-pull-up; 738 }; 739 pin-scl { 740 function = "alt5"; 741 pins = "gpio9"; 742 bias-disable; 743 }; 744 }; 745 i2c5_gpio10: i2c5-gpio10 { 746 pin-sda { 747 function = "alt5"; 748 pins = "gpio10"; 749 bias-pull-up; 750 }; 751 pin-scl { 752 function = "alt5"; 753 pins = "gpio11"; 754 bias-disable; 755 }; 756 }; 757 i2c5_gpio12: i2c5-gpio12 { 758 pin-sda { 759 function = "alt5"; 760 pins = "gpio12"; 761 bias-pull-up; 762 }; 763 pin-scl { 764 function = "alt5"; 765 pins = "gpio13"; 766 bias-disable; 767 }; 768 }; 769 i2c6_gpio0: i2c6-gpio0 { 770 pin-sda { 771 function = "alt5"; 772 pins = "gpio0"; 773 bias-pull-up; 774 }; 775 pin-scl { 776 function = "alt5"; 777 pins = "gpio1"; 778 bias-disable; 779 }; 780 }; 781 i2c6_gpio22: i2c6-gpio22 { 782 pin-sda { 783 function = "alt5"; 784 pins = "gpio22"; 785 bias-pull-up; 786 }; 787 pin-scl { 788 function = "alt5"; 789 pins = "gpio23"; 790 bias-disable; 791 }; 792 }; 793 i2c_slave_gpio8: i2c-slave-gpio8 { 794 pins-i2c-slave { 795 pins = "gpio8", 796 "gpio9", 797 "gpio10", 798 "gpio11"; 799 function = "alt3"; 800 }; 801 }; 802 803 jtag_gpio48: jtag-gpio48 { 804 pins-jtag { 805 pins = "gpio48", 806 "gpio49", 807 "gpio50", 808 "gpio51", 809 "gpio52", 810 "gpio53"; 811 function = "alt4"; 812 }; 813 }; 814 815 mii_gpio28: mii-gpio28 { 816 pins-mii { 817 pins = "gpio28", 818 "gpio29", 819 "gpio30", 820 "gpio31"; 821 function = "alt4"; 822 }; 823 }; 824 mii_gpio36: mii-gpio36 { 825 pins-mii { 826 pins = "gpio36", 827 "gpio37", 828 "gpio38", 829 "gpio39"; 830 function = "alt5"; 831 }; 832 }; 833 834 pcm_gpio50: pcm-gpio50 { 835 pins-pcm { 836 pins = "gpio50", 837 "gpio51", 838 "gpio52", 839 "gpio53"; 840 function = "alt2"; 841 }; 842 }; 843 844 pwm0_0_gpio12: pwm0-0-gpio12 { 845 pin-pwm { 846 pins = "gpio12"; 847 function = "alt0"; 848 bias-disable; 849 }; 850 }; 851 pwm0_0_gpio18: pwm0-0-gpio18 { 852 pin-pwm { 853 pins = "gpio18"; 854 function = "alt5"; 855 bias-disable; 856 }; 857 }; 858 pwm1_0_gpio40: pwm1-0-gpio40 { 859 pin-pwm { 860 pins = "gpio40"; 861 function = "alt0"; 862 bias-disable; 863 }; 864 }; 865 pwm0_1_gpio13: pwm0-1-gpio13 { 866 pin-pwm { 867 pins = "gpio13"; 868 function = "alt0"; 869 bias-disable; 870 }; 871 }; 872 pwm0_1_gpio19: pwm0-1-gpio19 { 873 pin-pwm { 874 pins = "gpio19"; 875 function = "alt5"; 876 bias-disable; 877 }; 878 }; 879 pwm1_1_gpio41: pwm1-1-gpio41 { 880 pin-pwm { 881 pins = "gpio41"; 882 function = "alt0"; 883 bias-disable; 884 }; 885 }; 886 pwm0_1_gpio45: pwm0-1-gpio45 { 887 pin-pwm { 888 pins = "gpio45"; 889 function = "alt0"; 890 bias-disable; 891 }; 892 }; 893 pwm0_0_gpio52: pwm0-0-gpio52 { 894 pin-pwm { 895 pins = "gpio52"; 896 function = "alt1"; 897 bias-disable; 898 }; 899 }; 900 pwm0_1_gpio53: pwm0-1-gpio53 { 901 pin-pwm { 902 pins = "gpio53"; 903 function = "alt1"; 904 bias-disable; 905 }; 906 }; 907 908 rgmii_gpio35: rgmii-gpio35 { 909 pin-start-stop { 910 pins = "gpio35"; 911 function = "alt4"; 912 }; 913 pin-rx-ok { 914 pins = "gpio36"; 915 function = "alt4"; 916 }; 917 }; 918 rgmii_irq_gpio34: rgmii-irq-gpio34 { 919 pin-irq { 920 pins = "gpio34"; 921 function = "alt5"; 922 }; 923 }; 924 rgmii_irq_gpio39: rgmii-irq-gpio39 { 925 pin-irq { 926 pins = "gpio39"; 927 function = "alt4"; 928 }; 929 }; 930 rgmii_mdio_gpio28: rgmii-mdio-gpio28 { 931 pins-mdio { 932 pins = "gpio28", 933 "gpio29"; 934 function = "alt5"; 935 }; 936 }; 937 rgmii_mdio_gpio37: rgmii-mdio-gpio37 { 938 pins-mdio { 939 pins = "gpio37", 940 "gpio38"; 941 function = "alt4"; 942 }; 943 }; 944 945 spi0_gpio46: spi0-gpio46 { 946 pins-spi { 947 pins = "gpio46", 948 "gpio47", 949 "gpio48", 950 "gpio49"; 951 function = "alt2"; 952 }; 953 }; 954 spi2_gpio46: spi2-gpio46 { 955 pins-spi { 956 pins = "gpio46", 957 "gpio47", 958 "gpio48", 959 "gpio49", 960 "gpio50"; 961 function = "alt5"; 962 }; 963 }; 964 spi3_gpio0: spi3-gpio0 { 965 pins-spi { 966 pins = "gpio0", 967 "gpio1", 968 "gpio2", 969 "gpio3"; 970 function = "alt3"; 971 }; 972 }; 973 spi4_gpio4: spi4-gpio4 { 974 pins-spi { 975 pins = "gpio4", 976 "gpio5", 977 "gpio6", 978 "gpio7"; 979 function = "alt3"; 980 }; 981 }; 982 spi5_gpio12: spi5-gpio12 { 983 pins-spi { 984 pins = "gpio12", 985 "gpio13", 986 "gpio14", 987 "gpio15"; 988 function = "alt3"; 989 }; 990 }; 991 spi6_gpio18: spi6-gpio18 { 992 pins-spi { 993 pins = "gpio18", 994 "gpio19", 995 "gpio20", 996 "gpio21"; 997 function = "alt3"; 998 }; 999 }; 1000 1001 uart2_gpio0: uart2-gpio0 { 1002 pin-tx { 1003 pins = "gpio0"; 1004 function = "alt4"; 1005 bias-disable; 1006 }; 1007 pin-rx { 1008 pins = "gpio1"; 1009 function = "alt4"; 1010 bias-pull-up; 1011 }; 1012 }; 1013 uart2_ctsrts_gpio2: uart2-ctsrts-gpio2 { 1014 pin-cts { 1015 pins = "gpio2"; 1016 function = "alt4"; 1017 bias-pull-up; 1018 }; 1019 pin-rts { 1020 pins = "gpio3"; 1021 function = "alt4"; 1022 bias-disable; 1023 }; 1024 }; 1025 uart3_gpio4: uart3-gpio4 { 1026 pin-tx { 1027 pins = "gpio4"; 1028 function = "alt4"; 1029 bias-disable; 1030 }; 1031 pin-rx { 1032 pins = "gpio5"; 1033 function = "alt4"; 1034 bias-pull-up; 1035 }; 1036 }; 1037 uart3_ctsrts_gpio6: uart3-ctsrts-gpio6 { 1038 pin-cts { 1039 pins = "gpio6"; 1040 function = "alt4"; 1041 bias-pull-up; 1042 }; 1043 pin-rts { 1044 pins = "gpio7"; 1045 function = "alt4"; 1046 bias-disable; 1047 }; 1048 }; 1049 uart4_gpio8: uart4-gpio8 { 1050 pin-tx { 1051 pins = "gpio8"; 1052 function = "alt4"; 1053 bias-disable; 1054 }; 1055 pin-rx { 1056 pins = "gpio9"; 1057 function = "alt4"; 1058 bias-pull-up; 1059 }; 1060 }; 1061 uart4_ctsrts_gpio10: uart4-ctsrts-gpio10 { 1062 pin-cts { 1063 pins = "gpio10"; 1064 function = "alt4"; 1065 bias-pull-up; 1066 }; 1067 pin-rts { 1068 pins = "gpio11"; 1069 function = "alt4"; 1070 bias-disable; 1071 }; 1072 }; 1073 uart5_gpio12: uart5-gpio12 { 1074 pin-tx { 1075 pins = "gpio12"; 1076 function = "alt4"; 1077 bias-disable; 1078 }; 1079 pin-rx { 1080 pins = "gpio13"; 1081 function = "alt4"; 1082 bias-pull-up; 1083 }; 1084 }; 1085 uart5_ctsrts_gpio14: uart5-ctsrts-gpio14 { 1086 pin-cts { 1087 pins = "gpio14"; 1088 function = "alt4"; 1089 bias-pull-up; 1090 }; 1091 pin-rts { 1092 pins = "gpio15"; 1093 function = "alt4"; 1094 bias-disable; 1095 }; 1096 }; 1097}; 1098 1099&rmem { 1100 #address-cells = <2>; 1101}; 1102 1103&cma { 1104 /* 1105 * arm64 reserves the CMA by default somewhere in ZONE_DMA32, 1106 * that's not good enough for the BCM2711 as some devices can 1107 * only address the lower 1G of memory (ZONE_DMA). 1108 */ 1109 alloc-ranges = <0x0 0x00000000 0x40000000>; 1110}; 1111 1112&i2c0 { 1113 compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; 1114 interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; 1115}; 1116 1117&i2c1 { 1118 compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; 1119 interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; 1120}; 1121 1122&mailbox { 1123 interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; 1124}; 1125 1126&sdhci { 1127 interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; 1128}; 1129 1130&sdhost { 1131 interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; 1132}; 1133 1134&spi { 1135 interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>; 1136}; 1137 1138&spi1 { 1139 interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; 1140}; 1141 1142&spi2 { 1143 interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; 1144}; 1145 1146&system_timer { 1147 interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>, 1148 <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, 1149 <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>, 1150 <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; 1151}; 1152 1153&txp { 1154 interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; 1155}; 1156 1157&uart0 { 1158 interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; 1159}; 1160 1161&uart1 { 1162 interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; 1163}; 1164 1165&usb { 1166 interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; 1167}; 1168 1169&vec { 1170 compatible = "brcm,bcm2711-vec"; 1171 interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; 1172}; 1173