1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * ARC HSDK Platform support code 4 * 5 * Copyright (C) 2017 Synopsys, Inc. (www.synopsys.com) 6 */ 7 8 #include <linux/init.h> 9 #include <linux/of_fdt.h> 10 #include <linux/libfdt.h> 11 #include <linux/smp.h> 12 #include <asm/arcregs.h> 13 #include <asm/io.h> 14 #include <asm/mach_desc.h> 15 16 int arc_hsdk_axi_dmac_coherent __section(".data") = 0; 17 18 #define ARC_CCM_UNUSED_ADDR 0x60000000 19 20 21 #define ARC_PERIPHERAL_BASE 0xf0000000 22 #define CREG_BASE (ARC_PERIPHERAL_BASE + 0x1000) 23 24 #define SDIO_BASE (ARC_PERIPHERAL_BASE + 0xA000) 25 #define SDIO_UHS_REG_EXT (SDIO_BASE + 0x108) 26 #define SDIO_UHS_REG_EXT_DIV_2 (2 << 30) 27 28 #define HSDK_GPIO_INTC (ARC_PERIPHERAL_BASE + 0x3000) 29 30 static void __init hsdk_enable_gpio_intc_wire(void) 31 { 32 /* 33 * Peripherals on CPU Card are wired to cpu intc via intermediate 34 * DW APB GPIO blocks (mainly for debouncing) 35 * 36 * --------------------- 37 * | snps,archs-intc | 38 * --------------------- 39 * | 40 * ---------------------- 41 * | snps,archs-idu-intc | 42 * ---------------------- 43 * | | | | | 44 * | [eth] [USB] [... other peripherals] 45 * | 46 * ------------------- 47 * | snps,dw-apb-intc | 48 * ------------------- 49 * | | | | 50 * [Bt] [HAPS] [... other peripherals] 51 * 52 * Current implementation of "irq-dw-apb-ictl" driver doesn't work well 53 * with stacked INTCs. In particular problem happens if its master INTC 54 * not yet instantiated. See discussion here - 55 * https://lore.kernel.org/lkml/54F6FE2C.7020309@synopsys.com 56 * 57 * So setup the first gpio block as a passive pass thru and hide it from 58 * DT hardware topology - connect intc directly to cpu intc 59 * The GPIO "wire" needs to be init nevertheless (here) 60 * 61 * One side adv is that peripheral interrupt handling avoids one nested 62 * intc ISR hop 63 * 64 * According to HSDK User's Manual [1], "Table 2 Interrupt Mapping" 65 * we have the following GPIO input lines used as sources of interrupt: 66 * - GPIO[0] - Bluetooth interrupt of RS9113 module 67 * - GPIO[2] - HAPS interrupt (on HapsTrak 3 connector) 68 * - GPIO[3] - Audio codec (MAX9880A) interrupt 69 * - GPIO[8-23] - Available on Arduino and PMOD_x headers 70 * For now there's no use of Arduino and PMOD_x headers in Linux 71 * use-case so we only enable lines 0, 2 and 3. 72 * 73 * [1] https://github.com/foss-for-synopsys-dwc-arc-processors/ARC-Development-Systems-Forum/wiki/docs/ARC_HSDK_User_Guide.pdf 74 */ 75 #define GPIO_INTEN (HSDK_GPIO_INTC + 0x30) 76 #define GPIO_INTMASK (HSDK_GPIO_INTC + 0x34) 77 #define GPIO_INTTYPE_LEVEL (HSDK_GPIO_INTC + 0x38) 78 #define GPIO_INT_POLARITY (HSDK_GPIO_INTC + 0x3c) 79 #define GPIO_INT_CONNECTED_MASK 0x0d 80 81 iowrite32(0xffffffff, (void __iomem *) GPIO_INTMASK); 82 iowrite32(~GPIO_INT_CONNECTED_MASK, (void __iomem *) GPIO_INTMASK); 83 iowrite32(0x00000000, (void __iomem *) GPIO_INTTYPE_LEVEL); 84 iowrite32(0xffffffff, (void __iomem *) GPIO_INT_POLARITY); 85 iowrite32(GPIO_INT_CONNECTED_MASK, (void __iomem *) GPIO_INTEN); 86 } 87 88 static int __init hsdk_tweak_node_coherency(const char *path, bool coherent) 89 { 90 void *fdt = initial_boot_params; 91 const void *prop; 92 int node, ret; 93 bool dt_coh_set; 94 95 node = fdt_path_offset(fdt, path); 96 if (node < 0) 97 goto tweak_fail; 98 99 prop = fdt_getprop(fdt, node, "dma-coherent", &ret); 100 if (!prop && ret != -FDT_ERR_NOTFOUND) 101 goto tweak_fail; 102 103 dt_coh_set = ret != -FDT_ERR_NOTFOUND; 104 ret = 0; 105 106 /* need to remove "dma-coherent" property */ 107 if (dt_coh_set && !coherent) 108 ret = fdt_delprop(fdt, node, "dma-coherent"); 109 110 /* need to set "dma-coherent" property */ 111 if (!dt_coh_set && coherent) 112 ret = fdt_setprop(fdt, node, "dma-coherent", NULL, 0); 113 114 if (ret < 0) 115 goto tweak_fail; 116 117 return 0; 118 119 tweak_fail: 120 pr_err("failed to tweak %s to %scoherent\n", path, coherent ? "" : "non"); 121 return -EFAULT; 122 } 123 124 enum hsdk_axi_masters { 125 M_HS_CORE = 0, 126 M_HS_RTT, 127 M_AXI_TUN, 128 M_HDMI_VIDEO, 129 M_HDMI_AUDIO, 130 M_USB_HOST, 131 M_ETHERNET, 132 M_SDIO, 133 M_GPU, 134 M_DMAC_0, 135 M_DMAC_1, 136 M_DVFS 137 }; 138 139 #define UPDATE_VAL 1 140 141 /* 142 * This is modified configuration of AXI bridge. Default settings 143 * are specified in "Table 111 CREG Address Decoder register reset values". 144 * 145 * AXI_M_m_SLV{0|1} - Slave Select register for master 'm'. 146 * Possible slaves are: 147 * - 0 => no slave selected 148 * - 1 => DDR controller port #1 149 * - 2 => SRAM controller 150 * - 3 => AXI tunnel 151 * - 4 => EBI controller 152 * - 5 => ROM controller 153 * - 6 => AXI2APB bridge 154 * - 7 => DDR controller port #2 155 * - 8 => DDR controller port #3 156 * - 9 => HS38x4 IOC 157 * - 10 => HS38x4 DMI 158 * AXI_M_m_OFFSET{0|1} - Addr Offset register for master 'm' 159 * 160 * Please read ARC HS Development IC Specification, section 17.2 for more 161 * information about apertures configuration. 162 * 163 * m master AXI_M_m_SLV0 AXI_M_m_SLV1 AXI_M_m_OFFSET0 AXI_M_m_OFFSET1 164 * 0 HS (CBU) 0x11111111 0x63111111 0xFEDCBA98 0x0E543210 165 * 1 HS (RTT) 0x77777777 0x77777777 0xFEDCBA98 0x76543210 166 * 2 AXI Tunnel 0x88888888 0x88888888 0xFEDCBA98 0x76543210 167 * 3 HDMI-VIDEO 0x77777777 0x77777777 0xFEDCBA98 0x76543210 168 * 4 HDMI-ADUIO 0x77777777 0x77777777 0xFEDCBA98 0x76543210 169 * 5 USB-HOST 0x77777777 0x77999999 0xFEDCBA98 0x76DCBA98 170 * 6 ETHERNET 0x77777777 0x77999999 0xFEDCBA98 0x76DCBA98 171 * 7 SDIO 0x77777777 0x77999999 0xFEDCBA98 0x76DCBA98 172 * 8 GPU 0x77777777 0x77777777 0xFEDCBA98 0x76543210 173 * 9 DMAC (port #1) 0x77777777 0x77777777 0xFEDCBA98 0x76543210 174 * 10 DMAC (port #2) 0x77777777 0x77777777 0xFEDCBA98 0x76543210 175 * 11 DVFS 0x00000000 0x60000000 0x00000000 0x00000000 176 */ 177 178 #define CREG_AXI_M_SLV0(m) ((void __iomem *)(CREG_BASE + 0x20 * (m))) 179 #define CREG_AXI_M_SLV1(m) ((void __iomem *)(CREG_BASE + 0x20 * (m) + 0x04)) 180 #define CREG_AXI_M_OFT0(m) ((void __iomem *)(CREG_BASE + 0x20 * (m) + 0x08)) 181 #define CREG_AXI_M_OFT1(m) ((void __iomem *)(CREG_BASE + 0x20 * (m) + 0x0C)) 182 #define CREG_AXI_M_UPDT(m) ((void __iomem *)(CREG_BASE + 0x20 * (m) + 0x14)) 183 184 #define CREG_AXI_M_HS_CORE_BOOT ((void __iomem *)(CREG_BASE + 0x010)) 185 186 #define CREG_PAE ((void __iomem *)(CREG_BASE + 0x180)) 187 #define CREG_PAE_UPDT ((void __iomem *)(CREG_BASE + 0x194)) 188 189 static void __init hsdk_init_memory_bridge_axi_dmac(void) 190 { 191 bool coherent = !!arc_hsdk_axi_dmac_coherent; 192 u32 axi_m_slv1, axi_m_oft1; 193 194 /* 195 * Don't tweak memory bridge configuration if we failed to tweak DTB 196 * as we will end up in a inconsistent state. 197 */ 198 if (hsdk_tweak_node_coherency("/soc/dmac@80000", coherent)) 199 return; 200 201 if (coherent) { 202 axi_m_slv1 = 0x77999999; 203 axi_m_oft1 = 0x76DCBA98; 204 } else { 205 axi_m_slv1 = 0x77777777; 206 axi_m_oft1 = 0x76543210; 207 } 208 209 writel(0x77777777, CREG_AXI_M_SLV0(M_DMAC_0)); 210 writel(0xFEDCBA98, CREG_AXI_M_OFT0(M_DMAC_0)); 211 writel(axi_m_slv1, CREG_AXI_M_SLV1(M_DMAC_0)); 212 writel(axi_m_oft1, CREG_AXI_M_OFT1(M_DMAC_0)); 213 writel(UPDATE_VAL, CREG_AXI_M_UPDT(M_DMAC_0)); 214 215 writel(0x77777777, CREG_AXI_M_SLV0(M_DMAC_1)); 216 writel(0xFEDCBA98, CREG_AXI_M_OFT0(M_DMAC_1)); 217 writel(axi_m_slv1, CREG_AXI_M_SLV1(M_DMAC_1)); 218 writel(axi_m_oft1, CREG_AXI_M_OFT1(M_DMAC_1)); 219 writel(UPDATE_VAL, CREG_AXI_M_UPDT(M_DMAC_1)); 220 } 221 222 static void __init hsdk_init_memory_bridge(void) 223 { 224 u32 reg; 225 226 /* 227 * M_HS_CORE has one unique register - BOOT. 228 * We need to clean boot mirror (BOOT[1:0]) bits in them to avoid first 229 * aperture to be masked by 'boot mirror'. 230 */ 231 reg = readl(CREG_AXI_M_HS_CORE_BOOT) & (~0x3); 232 writel(reg, CREG_AXI_M_HS_CORE_BOOT); 233 writel(0x11111111, CREG_AXI_M_SLV0(M_HS_CORE)); 234 writel(0x63111111, CREG_AXI_M_SLV1(M_HS_CORE)); 235 writel(0xFEDCBA98, CREG_AXI_M_OFT0(M_HS_CORE)); 236 writel(0x0E543210, CREG_AXI_M_OFT1(M_HS_CORE)); 237 writel(UPDATE_VAL, CREG_AXI_M_UPDT(M_HS_CORE)); 238 239 writel(0x77777777, CREG_AXI_M_SLV0(M_HS_RTT)); 240 writel(0x77777777, CREG_AXI_M_SLV1(M_HS_RTT)); 241 writel(0xFEDCBA98, CREG_AXI_M_OFT0(M_HS_RTT)); 242 writel(0x76543210, CREG_AXI_M_OFT1(M_HS_RTT)); 243 writel(UPDATE_VAL, CREG_AXI_M_UPDT(M_HS_RTT)); 244 245 writel(0x88888888, CREG_AXI_M_SLV0(M_AXI_TUN)); 246 writel(0x88888888, CREG_AXI_M_SLV1(M_AXI_TUN)); 247 writel(0xFEDCBA98, CREG_AXI_M_OFT0(M_AXI_TUN)); 248 writel(0x76543210, CREG_AXI_M_OFT1(M_AXI_TUN)); 249 writel(UPDATE_VAL, CREG_AXI_M_UPDT(M_AXI_TUN)); 250 251 writel(0x77777777, CREG_AXI_M_SLV0(M_HDMI_VIDEO)); 252 writel(0x77777777, CREG_AXI_M_SLV1(M_HDMI_VIDEO)); 253 writel(0xFEDCBA98, CREG_AXI_M_OFT0(M_HDMI_VIDEO)); 254 writel(0x76543210, CREG_AXI_M_OFT1(M_HDMI_VIDEO)); 255 writel(UPDATE_VAL, CREG_AXI_M_UPDT(M_HDMI_VIDEO)); 256 257 writel(0x77777777, CREG_AXI_M_SLV0(M_HDMI_AUDIO)); 258 writel(0x77777777, CREG_AXI_M_SLV1(M_HDMI_AUDIO)); 259 writel(0xFEDCBA98, CREG_AXI_M_OFT0(M_HDMI_AUDIO)); 260 writel(0x76543210, CREG_AXI_M_OFT1(M_HDMI_AUDIO)); 261 writel(UPDATE_VAL, CREG_AXI_M_UPDT(M_HDMI_AUDIO)); 262 263 writel(0x77777777, CREG_AXI_M_SLV0(M_USB_HOST)); 264 writel(0x77999999, CREG_AXI_M_SLV1(M_USB_HOST)); 265 writel(0xFEDCBA98, CREG_AXI_M_OFT0(M_USB_HOST)); 266 writel(0x76DCBA98, CREG_AXI_M_OFT1(M_USB_HOST)); 267 writel(UPDATE_VAL, CREG_AXI_M_UPDT(M_USB_HOST)); 268 269 writel(0x77777777, CREG_AXI_M_SLV0(M_ETHERNET)); 270 writel(0x77999999, CREG_AXI_M_SLV1(M_ETHERNET)); 271 writel(0xFEDCBA98, CREG_AXI_M_OFT0(M_ETHERNET)); 272 writel(0x76DCBA98, CREG_AXI_M_OFT1(M_ETHERNET)); 273 writel(UPDATE_VAL, CREG_AXI_M_UPDT(M_ETHERNET)); 274 275 writel(0x77777777, CREG_AXI_M_SLV0(M_SDIO)); 276 writel(0x77999999, CREG_AXI_M_SLV1(M_SDIO)); 277 writel(0xFEDCBA98, CREG_AXI_M_OFT0(M_SDIO)); 278 writel(0x76DCBA98, CREG_AXI_M_OFT1(M_SDIO)); 279 writel(UPDATE_VAL, CREG_AXI_M_UPDT(M_SDIO)); 280 281 writel(0x77777777, CREG_AXI_M_SLV0(M_GPU)); 282 writel(0x77777777, CREG_AXI_M_SLV1(M_GPU)); 283 writel(0xFEDCBA98, CREG_AXI_M_OFT0(M_GPU)); 284 writel(0x76543210, CREG_AXI_M_OFT1(M_GPU)); 285 writel(UPDATE_VAL, CREG_AXI_M_UPDT(M_GPU)); 286 287 writel(0x00000000, CREG_AXI_M_SLV0(M_DVFS)); 288 writel(0x60000000, CREG_AXI_M_SLV1(M_DVFS)); 289 writel(0x00000000, CREG_AXI_M_OFT0(M_DVFS)); 290 writel(0x00000000, CREG_AXI_M_OFT1(M_DVFS)); 291 writel(UPDATE_VAL, CREG_AXI_M_UPDT(M_DVFS)); 292 293 hsdk_init_memory_bridge_axi_dmac(); 294 295 /* 296 * PAE remapping for DMA clients does not work due to an RTL bug, so 297 * CREG_PAE register must be programmed to all zeroes, otherwise it 298 * will cause problems with DMA to/from peripherals even if PAE40 is 299 * not used. 300 */ 301 writel(0x00000000, CREG_PAE); 302 writel(UPDATE_VAL, CREG_PAE_UPDT); 303 } 304 305 static void __init hsdk_init_early(void) 306 { 307 hsdk_init_memory_bridge(); 308 309 /* 310 * Switch SDIO external ciu clock divider from default div-by-8 to 311 * minimum possible div-by-2. 312 */ 313 iowrite32(SDIO_UHS_REG_EXT_DIV_2, (void __iomem *) SDIO_UHS_REG_EXT); 314 315 hsdk_enable_gpio_intc_wire(); 316 } 317 318 static const char *hsdk_compat[] __initconst = { 319 "snps,hsdk", 320 NULL, 321 }; 322 323 MACHINE_START(SIMULATION, "hsdk") 324 .dt_compat = hsdk_compat, 325 .init_early = hsdk_init_early, 326 MACHINE_END 327