1.. SPDX-License-Identifier: GPL-2.0
2
3=======================
4Intel(R) Trace Hub (TH)
5=======================
6
7Overview
8--------
9
10Intel(R) Trace Hub (TH) is a set of hardware blocks that produce,
11switch and output trace data from multiple hardware and software
12sources over several types of trace output ports encoded in System
13Trace Protocol (MIPI STPv2) and is intended to perform full system
14debugging. For more information on the hardware, see Intel(R) Trace
15Hub developer's manual [1].
16
17It consists of trace sources, trace destinations (outputs) and a
18switch (Global Trace Hub, GTH). These devices are placed on a bus of
19their own ("intel_th"), where they can be discovered and configured
20via sysfs attributes.
21
22Currently, the following Intel TH subdevices (blocks) are supported:
23  - Software Trace Hub (STH), trace source, which is a System Trace
24    Module (STM) device,
25  - Memory Storage Unit (MSU), trace output, which allows storing
26    trace hub output in system memory,
27  - Parallel Trace Interface output (PTI), trace output to an external
28    debug host via a PTI port,
29  - Global Trace Hub (GTH), which is a switch and a central component
30    of Intel(R) Trace Hub architecture.
31
32Common attributes for output devices are described in
33Documentation/ABI/testing/sysfs-bus-intel_th-output-devices, the most
34notable of them is "active", which enables or disables trace output
35into that particular output device.
36
37GTH allows directing different STP masters into different output ports
38via its "masters" attribute group. More detailed GTH interface
39description is at Documentation/ABI/testing/sysfs-bus-intel_th-devices-gth.
40
41STH registers an stm class device, through which it provides interface
42to userspace and kernelspace software trace sources. See
43Documentation/trace/stm.rst for more information on that.
44
45MSU can be configured to collect trace data into a system memory
46buffer, which can later on be read from its device nodes via read() or
47mmap() interface and directed to a "software sink" driver that will
48consume the data and/or relay it further.
49
50On the whole, Intel(R) Trace Hub does not require any special
51userspace software to function; everything can be configured, started
52and collected via sysfs attributes, and device nodes.
53
54[1] https://software.intel.com/sites/default/files/managed/d3/3c/intel-th-developer-manual.pdf
55
56Bus and Subdevices
57------------------
58
59For each Intel TH device in the system a bus of its own is
60created and assigned an id number that reflects the order in which TH
61devices were emumerated. All TH subdevices (devices on intel_th bus)
62begin with this id: 0-gth, 0-msc0, 0-msc1, 0-pti, 0-sth, which is
63followed by device's name and an optional index.
64
65Output devices also get a device node in /dev/intel_thN, where N is
66the Intel TH device id. For example, MSU's memory buffers, when
67allocated, are accessible via /dev/intel_th0/msc{0,1}.
68
69Quick example
70-------------
71
72# figure out which GTH port is the first memory controller::
73
74	$ cat /sys/bus/intel_th/devices/0-msc0/port
75	0
76
77# looks like it's port 0, configure master 33 to send data to port 0::
78
79	$ echo 0 > /sys/bus/intel_th/devices/0-gth/masters/33
80
81# allocate a 2-windowed multiblock buffer on the first memory
82# controller, each with 64 pages::
83
84	$ echo multi > /sys/bus/intel_th/devices/0-msc0/mode
85	$ echo 64,64 > /sys/bus/intel_th/devices/0-msc0/nr_pages
86
87# enable wrapping for this controller, too::
88
89	$ echo 1 > /sys/bus/intel_th/devices/0-msc0/wrap
90
91# and enable tracing into this port::
92
93	$ echo 1 > /sys/bus/intel_th/devices/0-msc0/active
94
95# .. send data to master 33, see stm.txt for more details ..
96# .. wait for traces to pile up ..
97# .. and stop the trace::
98
99	$ echo 0 > /sys/bus/intel_th/devices/0-msc0/active
100
101# and now you can collect the trace from the device node::
102
103	$ cat /dev/intel_th0/msc0 > my_stp_trace
104
105Host Debugger Mode
106------------------
107
108It is possible to configure the Trace Hub and control its trace
109capture from a remote debug host, which should be connected via one of
110the hardware debugging interfaces, which will then be used to both
111control Intel Trace Hub and transfer its trace data to the debug host.
112
113The driver needs to be told that such an arrangement is taking place
114so that it does not touch any capture/port configuration and avoids
115conflicting with the debug host's configuration accesses. The only
116activity that the driver will perform in this mode is collecting
117software traces to the Software Trace Hub (an stm class device). The
118user is still responsible for setting up adequate master/channel
119mappings that the decoder on the receiving end would recognize.
120
121In order to enable the host mode, set the 'host_mode' parameter of the
122'intel_th' kernel module to 'y'. None of the virtual output devices
123will show up on the intel_th bus. Also, trace configuration and
124capture controlling attribute groups of the 'gth' device will not be
125exposed. The 'sth' device will operate as usual.
126
127Software Sinks
128--------------
129
130The Memory Storage Unit (MSU) driver provides an in-kernel API for
131drivers to register themselves as software sinks for the trace data.
132Such drivers can further export the data via other devices, such as
133USB device controllers or network cards.
134
135The API has two main parts::
136 - notifying the software sink that a particular window is full, and
137   "locking" that window, that is, making it unavailable for the trace
138   collection; when this happens, the MSU driver will automatically
139   switch to the next window in the buffer if it is unlocked, or stop
140   the trace capture if it's not;
141 - tracking the "locked" state of windows and providing a way for the
142   software sink driver to notify the MSU driver when a window is
143   unlocked and can be used again to collect trace data.
144
145An example sink driver, msu-sink illustrates the implementation of a
146software sink. Functionally, it simply unlocks windows as soon as they
147are full, keeping the MSU running in a circular buffer mode. Unlike the
148"multi" mode, it will fill out all the windows in the buffer as opposed
149to just the first one. It can be enabled by writing "sink" to the "mode"
150file (assuming msu-sink.ko is loaded).
151