1=================================== 2SocketCAN - Controller Area Network 3=================================== 4 5Overview / What is SocketCAN 6============================ 7 8The socketcan package is an implementation of CAN protocols 9(Controller Area Network) for Linux. CAN is a networking technology 10which has widespread use in automation, embedded devices, and 11automotive fields. While there have been other CAN implementations 12for Linux based on character devices, SocketCAN uses the Berkeley 13socket API, the Linux network stack and implements the CAN device 14drivers as network interfaces. The CAN socket API has been designed 15as similar as possible to the TCP/IP protocols to allow programmers, 16familiar with network programming, to easily learn how to use CAN 17sockets. 18 19 20.. _socketcan-motivation: 21 22Motivation / Why Using the Socket API 23===================================== 24 25There have been CAN implementations for Linux before SocketCAN so the 26question arises, why we have started another project. Most existing 27implementations come as a device driver for some CAN hardware, they 28are based on character devices and provide comparatively little 29functionality. Usually, there is only a hardware-specific device 30driver which provides a character device interface to send and 31receive raw CAN frames, directly to/from the controller hardware. 32Queueing of frames and higher-level transport protocols like ISO-TP 33have to be implemented in user space applications. Also, most 34character-device implementations support only one single process to 35open the device at a time, similar to a serial interface. Exchanging 36the CAN controller requires employment of another device driver and 37often the need for adaption of large parts of the application to the 38new driver's API. 39 40SocketCAN was designed to overcome all of these limitations. A new 41protocol family has been implemented which provides a socket interface 42to user space applications and which builds upon the Linux network 43layer, enabling use all of the provided queueing functionality. A device 44driver for CAN controller hardware registers itself with the Linux 45network layer as a network device, so that CAN frames from the 46controller can be passed up to the network layer and on to the CAN 47protocol family module and also vice-versa. Also, the protocol family 48module provides an API for transport protocol modules to register, so 49that any number of transport protocols can be loaded or unloaded 50dynamically. In fact, the can core module alone does not provide any 51protocol and cannot be used without loading at least one additional 52protocol module. Multiple sockets can be opened at the same time, 53on different or the same protocol module and they can listen/send 54frames on different or the same CAN IDs. Several sockets listening on 55the same interface for frames with the same CAN ID are all passed the 56same received matching CAN frames. An application wishing to 57communicate using a specific transport protocol, e.g. ISO-TP, just 58selects that protocol when opening the socket, and then can read and 59write application data byte streams, without having to deal with 60CAN-IDs, frames, etc. 61 62Similar functionality visible from user-space could be provided by a 63character device, too, but this would lead to a technically inelegant 64solution for a couple of reasons: 65 66* **Intricate usage:** Instead of passing a protocol argument to 67 socket(2) and using bind(2) to select a CAN interface and CAN ID, an 68 application would have to do all these operations using ioctl(2)s. 69 70* **Code duplication:** A character device cannot make use of the Linux 71 network queueing code, so all that code would have to be duplicated 72 for CAN networking. 73 74* **Abstraction:** In most existing character-device implementations, the 75 hardware-specific device driver for a CAN controller directly 76 provides the character device for the application to work with. 77 This is at least very unusual in Unix systems for both, char and 78 block devices. For example you don't have a character device for a 79 certain UART of a serial interface, a certain sound chip in your 80 computer, a SCSI or IDE controller providing access to your hard 81 disk or tape streamer device. Instead, you have abstraction layers 82 which provide a unified character or block device interface to the 83 application on the one hand, and a interface for hardware-specific 84 device drivers on the other hand. These abstractions are provided 85 by subsystems like the tty layer, the audio subsystem or the SCSI 86 and IDE subsystems for the devices mentioned above. 87 88 The easiest way to implement a CAN device driver is as a character 89 device without such a (complete) abstraction layer, as is done by most 90 existing drivers. The right way, however, would be to add such a 91 layer with all the functionality like registering for certain CAN 92 IDs, supporting several open file descriptors and (de)multiplexing 93 CAN frames between them, (sophisticated) queueing of CAN frames, and 94 providing an API for device drivers to register with. However, then 95 it would be no more difficult, or may be even easier, to use the 96 networking framework provided by the Linux kernel, and this is what 97 SocketCAN does. 98 99The use of the networking framework of the Linux kernel is just the 100natural and most appropriate way to implement CAN for Linux. 101 102 103.. _socketcan-concept: 104 105SocketCAN Concept 106================= 107 108As described in :ref:`socketcan-motivation` the main goal of SocketCAN is to 109provide a socket interface to user space applications which builds 110upon the Linux network layer. In contrast to the commonly known 111TCP/IP and ethernet networking, the CAN bus is a broadcast-only(!) 112medium that has no MAC-layer addressing like ethernet. The CAN-identifier 113(can_id) is used for arbitration on the CAN-bus. Therefore the CAN-IDs 114have to be chosen uniquely on the bus. When designing a CAN-ECU 115network the CAN-IDs are mapped to be sent by a specific ECU. 116For this reason a CAN-ID can be treated best as a kind of source address. 117 118 119.. _socketcan-receive-lists: 120 121Receive Lists 122------------- 123 124The network transparent access of multiple applications leads to the 125problem that different applications may be interested in the same 126CAN-IDs from the same CAN network interface. The SocketCAN core 127module - which implements the protocol family CAN - provides several 128high efficient receive lists for this reason. If e.g. a user space 129application opens a CAN RAW socket, the raw protocol module itself 130requests the (range of) CAN-IDs from the SocketCAN core that are 131requested by the user. The subscription and unsubscription of 132CAN-IDs can be done for specific CAN interfaces or for all(!) known 133CAN interfaces with the can_rx_(un)register() functions provided to 134CAN protocol modules by the SocketCAN core (see :ref:`socketcan-core-module`). 135To optimize the CPU usage at runtime the receive lists are split up 136into several specific lists per device that match the requested 137filter complexity for a given use-case. 138 139 140.. _socketcan-local-loopback1: 141 142Local Loopback of Sent Frames 143----------------------------- 144 145As known from other networking concepts the data exchanging 146applications may run on the same or different nodes without any 147change (except for the according addressing information): 148 149.. code:: 150 151 ___ ___ ___ _______ ___ 152 | _ | | _ | | _ | | _ _ | | _ | 153 ||A|| ||B|| ||C|| ||A| |B|| ||C|| 154 |___| |___| |___| |_______| |___| 155 | | | | | 156 -----------------(1)- CAN bus -(2)--------------- 157 158To ensure that application A receives the same information in the 159example (2) as it would receive in example (1) there is need for 160some kind of local loopback of the sent CAN frames on the appropriate 161node. 162 163The Linux network devices (by default) just can handle the 164transmission and reception of media dependent frames. Due to the 165arbitration on the CAN bus the transmission of a low prio CAN-ID 166may be delayed by the reception of a high prio CAN frame. To 167reflect the correct [#f1]_ traffic on the node the loopback of the sent 168data has to be performed right after a successful transmission. If 169the CAN network interface is not capable of performing the loopback for 170some reason the SocketCAN core can do this task as a fallback solution. 171See :ref:`socketcan-local-loopback2` for details (recommended). 172 173The loopback functionality is enabled by default to reflect standard 174networking behaviour for CAN applications. Due to some requests from 175the RT-SocketCAN group the loopback optionally may be disabled for each 176separate socket. See sockopts from the CAN RAW sockets in :ref:`socketcan-raw-sockets`. 177 178.. [#f1] you really like to have this when you're running analyser 179 tools like 'candump' or 'cansniffer' on the (same) node. 180 181 182.. _socketcan-network-problem-notifications: 183 184Network Problem Notifications 185----------------------------- 186 187The use of the CAN bus may lead to several problems on the physical 188and media access control layer. Detecting and logging of these lower 189layer problems is a vital requirement for CAN users to identify 190hardware issues on the physical transceiver layer as well as 191arbitration problems and error frames caused by the different 192ECUs. The occurrence of detected errors are important for diagnosis 193and have to be logged together with the exact timestamp. For this 194reason the CAN interface driver can generate so called Error Message 195Frames that can optionally be passed to the user application in the 196same way as other CAN frames. Whenever an error on the physical layer 197or the MAC layer is detected (e.g. by the CAN controller) the driver 198creates an appropriate error message frame. Error messages frames can 199be requested by the user application using the common CAN filter 200mechanisms. Inside this filter definition the (interested) type of 201errors may be selected. The reception of error messages is disabled 202by default. The format of the CAN error message frame is briefly 203described in the Linux header file "include/uapi/linux/can/error.h". 204 205 206How to use SocketCAN 207==================== 208 209Like TCP/IP, you first need to open a socket for communicating over a 210CAN network. Since SocketCAN implements a new protocol family, you 211need to pass PF_CAN as the first argument to the socket(2) system 212call. Currently, there are two CAN protocols to choose from, the raw 213socket protocol and the broadcast manager (BCM). So to open a socket, 214you would write:: 215 216 s = socket(PF_CAN, SOCK_RAW, CAN_RAW); 217 218and:: 219 220 s = socket(PF_CAN, SOCK_DGRAM, CAN_BCM); 221 222respectively. After the successful creation of the socket, you would 223normally use the bind(2) system call to bind the socket to a CAN 224interface (which is different from TCP/IP due to different addressing 225- see :ref:`socketcan-concept`). After binding (CAN_RAW) or connecting (CAN_BCM) 226the socket, you can read(2) and write(2) from/to the socket or use 227send(2), sendto(2), sendmsg(2) and the recv* counterpart operations 228on the socket as usual. There are also CAN specific socket options 229described below. 230 231The Classical CAN frame structure (aka CAN 2.0B), the CAN FD frame structure 232and the sockaddr structure are defined in include/linux/can.h: 233 234.. code-block:: C 235 236 struct can_frame { 237 canid_t can_id; /* 32 bit CAN_ID + EFF/RTR/ERR flags */ 238 union { 239 /* CAN frame payload length in byte (0 .. CAN_MAX_DLEN) 240 * was previously named can_dlc so we need to carry that 241 * name for legacy support 242 */ 243 __u8 len; 244 __u8 can_dlc; /* deprecated */ 245 }; 246 __u8 __pad; /* padding */ 247 __u8 __res0; /* reserved / padding */ 248 __u8 len8_dlc; /* optional DLC for 8 byte payload length (9 .. 15) */ 249 __u8 data[8] __attribute__((aligned(8))); 250 }; 251 252Remark: The len element contains the payload length in bytes and should be 253used instead of can_dlc. The deprecated can_dlc was misleadingly named as 254it always contained the plain payload length in bytes and not the so called 255'data length code' (DLC). 256 257To pass the raw DLC from/to a Classical CAN network device the len8_dlc 258element can contain values 9 .. 15 when the len element is 8 (the real 259payload length for all DLC values greater or equal to 8). 260 261The alignment of the (linear) payload data[] to a 64bit boundary 262allows the user to define their own structs and unions to easily access 263the CAN payload. There is no given byteorder on the CAN bus by 264default. A read(2) system call on a CAN_RAW socket transfers a 265struct can_frame to the user space. 266 267The sockaddr_can structure has an interface index like the 268PF_PACKET socket, that also binds to a specific interface: 269 270.. code-block:: C 271 272 struct sockaddr_can { 273 sa_family_t can_family; 274 int can_ifindex; 275 union { 276 /* transport protocol class address info (e.g. ISOTP) */ 277 struct { canid_t rx_id, tx_id; } tp; 278 279 /* J1939 address information */ 280 struct { 281 /* 8 byte name when using dynamic addressing */ 282 __u64 name; 283 284 /* pgn: 285 * 8 bit: PS in PDU2 case, else 0 286 * 8 bit: PF 287 * 1 bit: DP 288 * 1 bit: reserved 289 */ 290 __u32 pgn; 291 292 /* 1 byte address */ 293 __u8 addr; 294 } j1939; 295 296 /* reserved for future CAN protocols address information */ 297 } can_addr; 298 }; 299 300To determine the interface index an appropriate ioctl() has to 301be used (example for CAN_RAW sockets without error checking): 302 303.. code-block:: C 304 305 int s; 306 struct sockaddr_can addr; 307 struct ifreq ifr; 308 309 s = socket(PF_CAN, SOCK_RAW, CAN_RAW); 310 311 strcpy(ifr.ifr_name, "can0" ); 312 ioctl(s, SIOCGIFINDEX, &ifr); 313 314 addr.can_family = AF_CAN; 315 addr.can_ifindex = ifr.ifr_ifindex; 316 317 bind(s, (struct sockaddr *)&addr, sizeof(addr)); 318 319 (..) 320 321To bind a socket to all(!) CAN interfaces the interface index must 322be 0 (zero). In this case the socket receives CAN frames from every 323enabled CAN interface. To determine the originating CAN interface 324the system call recvfrom(2) may be used instead of read(2). To send 325on a socket that is bound to 'any' interface sendto(2) is needed to 326specify the outgoing interface. 327 328Reading CAN frames from a bound CAN_RAW socket (see above) consists 329of reading a struct can_frame: 330 331.. code-block:: C 332 333 struct can_frame frame; 334 335 nbytes = read(s, &frame, sizeof(struct can_frame)); 336 337 if (nbytes < 0) { 338 perror("can raw socket read"); 339 return 1; 340 } 341 342 /* paranoid check ... */ 343 if (nbytes < sizeof(struct can_frame)) { 344 fprintf(stderr, "read: incomplete CAN frame\n"); 345 return 1; 346 } 347 348 /* do something with the received CAN frame */ 349 350Writing CAN frames can be done similarly, with the write(2) system call:: 351 352 nbytes = write(s, &frame, sizeof(struct can_frame)); 353 354When the CAN interface is bound to 'any' existing CAN interface 355(addr.can_ifindex = 0) it is recommended to use recvfrom(2) if the 356information about the originating CAN interface is needed: 357 358.. code-block:: C 359 360 struct sockaddr_can addr; 361 struct ifreq ifr; 362 socklen_t len = sizeof(addr); 363 struct can_frame frame; 364 365 nbytes = recvfrom(s, &frame, sizeof(struct can_frame), 366 0, (struct sockaddr*)&addr, &len); 367 368 /* get interface name of the received CAN frame */ 369 ifr.ifr_ifindex = addr.can_ifindex; 370 ioctl(s, SIOCGIFNAME, &ifr); 371 printf("Received a CAN frame from interface %s", ifr.ifr_name); 372 373To write CAN frames on sockets bound to 'any' CAN interface the 374outgoing interface has to be defined certainly: 375 376.. code-block:: C 377 378 strcpy(ifr.ifr_name, "can0"); 379 ioctl(s, SIOCGIFINDEX, &ifr); 380 addr.can_ifindex = ifr.ifr_ifindex; 381 addr.can_family = AF_CAN; 382 383 nbytes = sendto(s, &frame, sizeof(struct can_frame), 384 0, (struct sockaddr*)&addr, sizeof(addr)); 385 386An accurate timestamp can be obtained with an ioctl(2) call after reading 387a message from the socket: 388 389.. code-block:: C 390 391 struct timeval tv; 392 ioctl(s, SIOCGSTAMP, &tv); 393 394The timestamp has a resolution of one microsecond and is set automatically 395at the reception of a CAN frame. 396 397Remark about CAN FD (flexible data rate) support: 398 399Generally the handling of CAN FD is very similar to the formerly described 400examples. The new CAN FD capable CAN controllers support two different 401bitrates for the arbitration phase and the payload phase of the CAN FD frame 402and up to 64 bytes of payload. This extended payload length breaks all the 403kernel interfaces (ABI) which heavily rely on the CAN frame with fixed eight 404bytes of payload (struct can_frame) like the CAN_RAW socket. Therefore e.g. 405the CAN_RAW socket supports a new socket option CAN_RAW_FD_FRAMES that 406switches the socket into a mode that allows the handling of CAN FD frames 407and Classical CAN frames simultaneously (see :ref:`socketcan-rawfd`). 408 409The struct canfd_frame is defined in include/linux/can.h: 410 411.. code-block:: C 412 413 struct canfd_frame { 414 canid_t can_id; /* 32 bit CAN_ID + EFF/RTR/ERR flags */ 415 __u8 len; /* frame payload length in byte (0 .. 64) */ 416 __u8 flags; /* additional flags for CAN FD */ 417 __u8 __res0; /* reserved / padding */ 418 __u8 __res1; /* reserved / padding */ 419 __u8 data[64] __attribute__((aligned(8))); 420 }; 421 422The struct canfd_frame and the existing struct can_frame have the can_id, 423the payload length and the payload data at the same offset inside their 424structures. This allows to handle the different structures very similar. 425When the content of a struct can_frame is copied into a struct canfd_frame 426all structure elements can be used as-is - only the data[] becomes extended. 427 428When introducing the struct canfd_frame it turned out that the data length 429code (DLC) of the struct can_frame was used as a length information as the 430length and the DLC has a 1:1 mapping in the range of 0 .. 8. To preserve 431the easy handling of the length information the canfd_frame.len element 432contains a plain length value from 0 .. 64. So both canfd_frame.len and 433can_frame.len are equal and contain a length information and no DLC. 434For details about the distinction of CAN and CAN FD capable devices and 435the mapping to the bus-relevant data length code (DLC), see :ref:`socketcan-can-fd-driver`. 436 437The length of the two CAN(FD) frame structures define the maximum transfer 438unit (MTU) of the CAN(FD) network interface and skbuff data length. Two 439definitions are specified for CAN specific MTUs in include/linux/can.h: 440 441.. code-block:: C 442 443 #define CAN_MTU (sizeof(struct can_frame)) == 16 => Classical CAN frame 444 #define CANFD_MTU (sizeof(struct canfd_frame)) == 72 => CAN FD frame 445 446 447.. _socketcan-raw-sockets: 448 449RAW Protocol Sockets with can_filters (SOCK_RAW) 450------------------------------------------------ 451 452Using CAN_RAW sockets is extensively comparable to the commonly 453known access to CAN character devices. To meet the new possibilities 454provided by the multi user SocketCAN approach, some reasonable 455defaults are set at RAW socket binding time: 456 457- The filters are set to exactly one filter receiving everything 458- The socket only receives valid data frames (=> no error message frames) 459- The loopback of sent CAN frames is enabled (see :ref:`socketcan-local-loopback2`) 460- The socket does not receive its own sent frames (in loopback mode) 461 462These default settings may be changed before or after binding the socket. 463To use the referenced definitions of the socket options for CAN_RAW 464sockets, include <linux/can/raw.h>. 465 466 467.. _socketcan-rawfilter: 468 469RAW socket option CAN_RAW_FILTER 470~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 471 472The reception of CAN frames using CAN_RAW sockets can be controlled 473by defining 0 .. n filters with the CAN_RAW_FILTER socket option. 474 475The CAN filter structure is defined in include/linux/can.h: 476 477.. code-block:: C 478 479 struct can_filter { 480 canid_t can_id; 481 canid_t can_mask; 482 }; 483 484A filter matches, when: 485 486.. code-block:: C 487 488 <received_can_id> & mask == can_id & mask 489 490which is analogous to known CAN controllers hardware filter semantics. 491The filter can be inverted in this semantic, when the CAN_INV_FILTER 492bit is set in can_id element of the can_filter structure. In 493contrast to CAN controller hardware filters the user may set 0 .. n 494receive filters for each open socket separately: 495 496.. code-block:: C 497 498 struct can_filter rfilter[2]; 499 500 rfilter[0].can_id = 0x123; 501 rfilter[0].can_mask = CAN_SFF_MASK; 502 rfilter[1].can_id = 0x200; 503 rfilter[1].can_mask = 0x700; 504 505 setsockopt(s, SOL_CAN_RAW, CAN_RAW_FILTER, &rfilter, sizeof(rfilter)); 506 507To disable the reception of CAN frames on the selected CAN_RAW socket: 508 509.. code-block:: C 510 511 setsockopt(s, SOL_CAN_RAW, CAN_RAW_FILTER, NULL, 0); 512 513To set the filters to zero filters is quite obsolete as to not read 514data causes the raw socket to discard the received CAN frames. But 515having this 'send only' use-case we may remove the receive list in the 516Kernel to save a little (really a very little!) CPU usage. 517 518CAN Filter Usage Optimisation 519............................. 520 521The CAN filters are processed in per-device filter lists at CAN frame 522reception time. To reduce the number of checks that need to be performed 523while walking through the filter lists the CAN core provides an optimized 524filter handling when the filter subscription focusses on a single CAN ID. 525 526For the possible 2048 SFF CAN identifiers the identifier is used as an index 527to access the corresponding subscription list without any further checks. 528For the 2^29 possible EFF CAN identifiers a 10 bit XOR folding is used as 529hash function to retrieve the EFF table index. 530 531To benefit from the optimized filters for single CAN identifiers the 532CAN_SFF_MASK or CAN_EFF_MASK have to be set into can_filter.mask together 533with set CAN_EFF_FLAG and CAN_RTR_FLAG bits. A set CAN_EFF_FLAG bit in the 534can_filter.mask makes clear that it matters whether a SFF or EFF CAN ID is 535subscribed. E.g. in the example from above: 536 537.. code-block:: C 538 539 rfilter[0].can_id = 0x123; 540 rfilter[0].can_mask = CAN_SFF_MASK; 541 542both SFF frames with CAN ID 0x123 and EFF frames with 0xXXXXX123 can pass. 543 544To filter for only 0x123 (SFF) and 0x12345678 (EFF) CAN identifiers the 545filter has to be defined in this way to benefit from the optimized filters: 546 547.. code-block:: C 548 549 struct can_filter rfilter[2]; 550 551 rfilter[0].can_id = 0x123; 552 rfilter[0].can_mask = (CAN_EFF_FLAG | CAN_RTR_FLAG | CAN_SFF_MASK); 553 rfilter[1].can_id = 0x12345678 | CAN_EFF_FLAG; 554 rfilter[1].can_mask = (CAN_EFF_FLAG | CAN_RTR_FLAG | CAN_EFF_MASK); 555 556 setsockopt(s, SOL_CAN_RAW, CAN_RAW_FILTER, &rfilter, sizeof(rfilter)); 557 558 559RAW Socket Option CAN_RAW_ERR_FILTER 560~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 561 562As described in :ref:`socketcan-network-problem-notifications` the CAN interface driver can generate so 563called Error Message Frames that can optionally be passed to the user 564application in the same way as other CAN frames. The possible 565errors are divided into different error classes that may be filtered 566using the appropriate error mask. To register for every possible 567error condition CAN_ERR_MASK can be used as value for the error mask. 568The values for the error mask are defined in linux/can/error.h: 569 570.. code-block:: C 571 572 can_err_mask_t err_mask = ( CAN_ERR_TX_TIMEOUT | CAN_ERR_BUSOFF ); 573 574 setsockopt(s, SOL_CAN_RAW, CAN_RAW_ERR_FILTER, 575 &err_mask, sizeof(err_mask)); 576 577 578RAW Socket Option CAN_RAW_LOOPBACK 579~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 580 581To meet multi user needs the local loopback is enabled by default 582(see :ref:`socketcan-local-loopback1` for details). But in some embedded use-cases 583(e.g. when only one application uses the CAN bus) this loopback 584functionality can be disabled (separately for each socket): 585 586.. code-block:: C 587 588 int loopback = 0; /* 0 = disabled, 1 = enabled (default) */ 589 590 setsockopt(s, SOL_CAN_RAW, CAN_RAW_LOOPBACK, &loopback, sizeof(loopback)); 591 592 593RAW socket option CAN_RAW_RECV_OWN_MSGS 594~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 595 596When the local loopback is enabled, all the sent CAN frames are 597looped back to the open CAN sockets that registered for the CAN 598frames' CAN-ID on this given interface to meet the multi user 599needs. The reception of the CAN frames on the same socket that was 600sending the CAN frame is assumed to be unwanted and therefore 601disabled by default. This default behaviour may be changed on 602demand: 603 604.. code-block:: C 605 606 int recv_own_msgs = 1; /* 0 = disabled (default), 1 = enabled */ 607 608 setsockopt(s, SOL_CAN_RAW, CAN_RAW_RECV_OWN_MSGS, 609 &recv_own_msgs, sizeof(recv_own_msgs)); 610 611Note that reception of a socket's own CAN frames are subject to the same 612filtering as other CAN frames (see :ref:`socketcan-rawfilter`). 613 614.. _socketcan-rawfd: 615 616RAW Socket Option CAN_RAW_FD_FRAMES 617~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 618 619CAN FD support in CAN_RAW sockets can be enabled with a new socket option 620CAN_RAW_FD_FRAMES which is off by default. When the new socket option is 621not supported by the CAN_RAW socket (e.g. on older kernels), switching the 622CAN_RAW_FD_FRAMES option returns the error -ENOPROTOOPT. 623 624Once CAN_RAW_FD_FRAMES is enabled the application can send both CAN frames 625and CAN FD frames. OTOH the application has to handle CAN and CAN FD frames 626when reading from the socket: 627 628.. code-block:: C 629 630 CAN_RAW_FD_FRAMES enabled: CAN_MTU and CANFD_MTU are allowed 631 CAN_RAW_FD_FRAMES disabled: only CAN_MTU is allowed (default) 632 633Example: 634 635.. code-block:: C 636 637 [ remember: CANFD_MTU == sizeof(struct canfd_frame) ] 638 639 struct canfd_frame cfd; 640 641 nbytes = read(s, &cfd, CANFD_MTU); 642 643 if (nbytes == CANFD_MTU) { 644 printf("got CAN FD frame with length %d\n", cfd.len); 645 /* cfd.flags contains valid data */ 646 } else if (nbytes == CAN_MTU) { 647 printf("got Classical CAN frame with length %d\n", cfd.len); 648 /* cfd.flags is undefined */ 649 } else { 650 fprintf(stderr, "read: invalid CAN(FD) frame\n"); 651 return 1; 652 } 653 654 /* the content can be handled independently from the received MTU size */ 655 656 printf("can_id: %X data length: %d data: ", cfd.can_id, cfd.len); 657 for (i = 0; i < cfd.len; i++) 658 printf("%02X ", cfd.data[i]); 659 660When reading with size CANFD_MTU only returns CAN_MTU bytes that have 661been received from the socket a Classical CAN frame has been read into the 662provided CAN FD structure. Note that the canfd_frame.flags data field is 663not specified in the struct can_frame and therefore it is only valid in 664CANFD_MTU sized CAN FD frames. 665 666Implementation hint for new CAN applications: 667 668To build a CAN FD aware application use struct canfd_frame as basic CAN 669data structure for CAN_RAW based applications. When the application is 670executed on an older Linux kernel and switching the CAN_RAW_FD_FRAMES 671socket option returns an error: No problem. You'll get Classical CAN frames 672or CAN FD frames and can process them the same way. 673 674When sending to CAN devices make sure that the device is capable to handle 675CAN FD frames by checking if the device maximum transfer unit is CANFD_MTU. 676The CAN device MTU can be retrieved e.g. with a SIOCGIFMTU ioctl() syscall. 677 678 679RAW socket option CAN_RAW_JOIN_FILTERS 680~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 681 682The CAN_RAW socket can set multiple CAN identifier specific filters that 683lead to multiple filters in the af_can.c filter processing. These filters 684are indenpendent from each other which leads to logical OR'ed filters when 685applied (see :ref:`socketcan-rawfilter`). 686 687This socket option joines the given CAN filters in the way that only CAN 688frames are passed to user space that matched *all* given CAN filters. The 689semantic for the applied filters is therefore changed to a logical AND. 690 691This is useful especially when the filterset is a combination of filters 692where the CAN_INV_FILTER flag is set in order to notch single CAN IDs or 693CAN ID ranges from the incoming traffic. 694 695 696RAW Socket Returned Message Flags 697~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 698 699When using recvmsg() call, the msg->msg_flags may contain following flags: 700 701MSG_DONTROUTE: 702 set when the received frame was created on the local host. 703 704MSG_CONFIRM: 705 set when the frame was sent via the socket it is received on. 706 This flag can be interpreted as a 'transmission confirmation' when the 707 CAN driver supports the echo of frames on driver level, see 708 :ref:`socketcan-local-loopback1` and :ref:`socketcan-local-loopback2`. 709 In order to receive such messages, CAN_RAW_RECV_OWN_MSGS must be set. 710 711 712Broadcast Manager Protocol Sockets (SOCK_DGRAM) 713----------------------------------------------- 714 715The Broadcast Manager protocol provides a command based configuration 716interface to filter and send (e.g. cyclic) CAN messages in kernel space. 717 718Receive filters can be used to down sample frequent messages; detect events 719such as message contents changes, packet length changes, and do time-out 720monitoring of received messages. 721 722Periodic transmission tasks of CAN frames or a sequence of CAN frames can be 723created and modified at runtime; both the message content and the two 724possible transmit intervals can be altered. 725 726A BCM socket is not intended for sending individual CAN frames using the 727struct can_frame as known from the CAN_RAW socket. Instead a special BCM 728configuration message is defined. The basic BCM configuration message used 729to communicate with the broadcast manager and the available operations are 730defined in the linux/can/bcm.h include. The BCM message consists of a 731message header with a command ('opcode') followed by zero or more CAN frames. 732The broadcast manager sends responses to user space in the same form: 733 734.. code-block:: C 735 736 struct bcm_msg_head { 737 __u32 opcode; /* command */ 738 __u32 flags; /* special flags */ 739 __u32 count; /* run 'count' times with ival1 */ 740 struct timeval ival1, ival2; /* count and subsequent interval */ 741 canid_t can_id; /* unique can_id for task */ 742 __u32 nframes; /* number of can_frames following */ 743 struct can_frame frames[0]; 744 }; 745 746The aligned payload 'frames' uses the same basic CAN frame structure defined 747at the beginning of :ref:`socketcan-rawfd` and in the include/linux/can.h include. All 748messages to the broadcast manager from user space have this structure. 749 750Note a CAN_BCM socket must be connected instead of bound after socket 751creation (example without error checking): 752 753.. code-block:: C 754 755 int s; 756 struct sockaddr_can addr; 757 struct ifreq ifr; 758 759 s = socket(PF_CAN, SOCK_DGRAM, CAN_BCM); 760 761 strcpy(ifr.ifr_name, "can0"); 762 ioctl(s, SIOCGIFINDEX, &ifr); 763 764 addr.can_family = AF_CAN; 765 addr.can_ifindex = ifr.ifr_ifindex; 766 767 connect(s, (struct sockaddr *)&addr, sizeof(addr)); 768 769 (..) 770 771The broadcast manager socket is able to handle any number of in flight 772transmissions or receive filters concurrently. The different RX/TX jobs are 773distinguished by the unique can_id in each BCM message. However additional 774CAN_BCM sockets are recommended to communicate on multiple CAN interfaces. 775When the broadcast manager socket is bound to 'any' CAN interface (=> the 776interface index is set to zero) the configured receive filters apply to any 777CAN interface unless the sendto() syscall is used to overrule the 'any' CAN 778interface index. When using recvfrom() instead of read() to retrieve BCM 779socket messages the originating CAN interface is provided in can_ifindex. 780 781 782Broadcast Manager Operations 783~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 784 785The opcode defines the operation for the broadcast manager to carry out, 786or details the broadcast managers response to several events, including 787user requests. 788 789Transmit Operations (user space to broadcast manager): 790 791TX_SETUP: 792 Create (cyclic) transmission task. 793 794TX_DELETE: 795 Remove (cyclic) transmission task, requires only can_id. 796 797TX_READ: 798 Read properties of (cyclic) transmission task for can_id. 799 800TX_SEND: 801 Send one CAN frame. 802 803Transmit Responses (broadcast manager to user space): 804 805TX_STATUS: 806 Reply to TX_READ request (transmission task configuration). 807 808TX_EXPIRED: 809 Notification when counter finishes sending at initial interval 810 'ival1'. Requires the TX_COUNTEVT flag to be set at TX_SETUP. 811 812Receive Operations (user space to broadcast manager): 813 814RX_SETUP: 815 Create RX content filter subscription. 816 817RX_DELETE: 818 Remove RX content filter subscription, requires only can_id. 819 820RX_READ: 821 Read properties of RX content filter subscription for can_id. 822 823Receive Responses (broadcast manager to user space): 824 825RX_STATUS: 826 Reply to RX_READ request (filter task configuration). 827 828RX_TIMEOUT: 829 Cyclic message is detected to be absent (timer ival1 expired). 830 831RX_CHANGED: 832 BCM message with updated CAN frame (detected content change). 833 Sent on first message received or on receipt of revised CAN messages. 834 835 836Broadcast Manager Message Flags 837~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 838 839When sending a message to the broadcast manager the 'flags' element may 840contain the following flag definitions which influence the behaviour: 841 842SETTIMER: 843 Set the values of ival1, ival2 and count 844 845STARTTIMER: 846 Start the timer with the actual values of ival1, ival2 847 and count. Starting the timer leads simultaneously to emit a CAN frame. 848 849TX_COUNTEVT: 850 Create the message TX_EXPIRED when count expires 851 852TX_ANNOUNCE: 853 A change of data by the process is emitted immediately. 854 855TX_CP_CAN_ID: 856 Copies the can_id from the message header to each 857 subsequent frame in frames. This is intended as usage simplification. For 858 TX tasks the unique can_id from the message header may differ from the 859 can_id(s) stored for transmission in the subsequent struct can_frame(s). 860 861RX_FILTER_ID: 862 Filter by can_id alone, no frames required (nframes=0). 863 864RX_CHECK_DLC: 865 A change of the DLC leads to an RX_CHANGED. 866 867RX_NO_AUTOTIMER: 868 Prevent automatically starting the timeout monitor. 869 870RX_ANNOUNCE_RESUME: 871 If passed at RX_SETUP and a receive timeout occurred, a 872 RX_CHANGED message will be generated when the (cyclic) receive restarts. 873 874TX_RESET_MULTI_IDX: 875 Reset the index for the multiple frame transmission. 876 877RX_RTR_FRAME: 878 Send reply for RTR-request (placed in op->frames[0]). 879 880CAN_FD_FRAME: 881 The CAN frames following the bcm_msg_head are struct canfd_frame's 882 883Broadcast Manager Transmission Timers 884~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 885 886Periodic transmission configurations may use up to two interval timers. 887In this case the BCM sends a number of messages ('count') at an interval 888'ival1', then continuing to send at another given interval 'ival2'. When 889only one timer is needed 'count' is set to zero and only 'ival2' is used. 890When SET_TIMER and START_TIMER flag were set the timers are activated. 891The timer values can be altered at runtime when only SET_TIMER is set. 892 893 894Broadcast Manager message sequence transmission 895~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 896 897Up to 256 CAN frames can be transmitted in a sequence in the case of a cyclic 898TX task configuration. The number of CAN frames is provided in the 'nframes' 899element of the BCM message head. The defined number of CAN frames are added 900as array to the TX_SETUP BCM configuration message: 901 902.. code-block:: C 903 904 /* create a struct to set up a sequence of four CAN frames */ 905 struct { 906 struct bcm_msg_head msg_head; 907 struct can_frame frame[4]; 908 } mytxmsg; 909 910 (..) 911 mytxmsg.msg_head.nframes = 4; 912 (..) 913 914 write(s, &mytxmsg, sizeof(mytxmsg)); 915 916With every transmission the index in the array of CAN frames is increased 917and set to zero at index overflow. 918 919 920Broadcast Manager Receive Filter Timers 921~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 922 923The timer values ival1 or ival2 may be set to non-zero values at RX_SETUP. 924When the SET_TIMER flag is set the timers are enabled: 925 926ival1: 927 Send RX_TIMEOUT when a received message is not received again within 928 the given time. When START_TIMER is set at RX_SETUP the timeout detection 929 is activated directly - even without a former CAN frame reception. 930 931ival2: 932 Throttle the received message rate down to the value of ival2. This 933 is useful to reduce messages for the application when the signal inside the 934 CAN frame is stateless as state changes within the ival2 periode may get 935 lost. 936 937Broadcast Manager Multiplex Message Receive Filter 938~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 939 940To filter for content changes in multiplex message sequences an array of more 941than one CAN frames can be passed in a RX_SETUP configuration message. The 942data bytes of the first CAN frame contain the mask of relevant bits that 943have to match in the subsequent CAN frames with the received CAN frame. 944If one of the subsequent CAN frames is matching the bits in that frame data 945mark the relevant content to be compared with the previous received content. 946Up to 257 CAN frames (multiplex filter bit mask CAN frame plus 256 CAN 947filters) can be added as array to the TX_SETUP BCM configuration message: 948 949.. code-block:: C 950 951 /* usually used to clear CAN frame data[] - beware of endian problems! */ 952 #define U64_DATA(p) (*(unsigned long long*)(p)->data) 953 954 struct { 955 struct bcm_msg_head msg_head; 956 struct can_frame frame[5]; 957 } msg; 958 959 msg.msg_head.opcode = RX_SETUP; 960 msg.msg_head.can_id = 0x42; 961 msg.msg_head.flags = 0; 962 msg.msg_head.nframes = 5; 963 U64_DATA(&msg.frame[0]) = 0xFF00000000000000ULL; /* MUX mask */ 964 U64_DATA(&msg.frame[1]) = 0x01000000000000FFULL; /* data mask (MUX 0x01) */ 965 U64_DATA(&msg.frame[2]) = 0x0200FFFF000000FFULL; /* data mask (MUX 0x02) */ 966 U64_DATA(&msg.frame[3]) = 0x330000FFFFFF0003ULL; /* data mask (MUX 0x33) */ 967 U64_DATA(&msg.frame[4]) = 0x4F07FC0FF0000000ULL; /* data mask (MUX 0x4F) */ 968 969 write(s, &msg, sizeof(msg)); 970 971 972Broadcast Manager CAN FD Support 973~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 974 975The programming API of the CAN_BCM depends on struct can_frame which is 976given as array directly behind the bcm_msg_head structure. To follow this 977schema for the CAN FD frames a new flag 'CAN_FD_FRAME' in the bcm_msg_head 978flags indicates that the concatenated CAN frame structures behind the 979bcm_msg_head are defined as struct canfd_frame: 980 981.. code-block:: C 982 983 struct { 984 struct bcm_msg_head msg_head; 985 struct canfd_frame frame[5]; 986 } msg; 987 988 msg.msg_head.opcode = RX_SETUP; 989 msg.msg_head.can_id = 0x42; 990 msg.msg_head.flags = CAN_FD_FRAME; 991 msg.msg_head.nframes = 5; 992 (..) 993 994When using CAN FD frames for multiplex filtering the MUX mask is still 995expected in the first 64 bit of the struct canfd_frame data section. 996 997 998Connected Transport Protocols (SOCK_SEQPACKET) 999---------------------------------------------- 1000 1001(to be written) 1002 1003 1004Unconnected Transport Protocols (SOCK_DGRAM) 1005-------------------------------------------- 1006 1007(to be written) 1008 1009 1010.. _socketcan-core-module: 1011 1012SocketCAN Core Module 1013===================== 1014 1015The SocketCAN core module implements the protocol family 1016PF_CAN. CAN protocol modules are loaded by the core module at 1017runtime. The core module provides an interface for CAN protocol 1018modules to subscribe needed CAN IDs (see :ref:`socketcan-receive-lists`). 1019 1020 1021can.ko Module Params 1022-------------------- 1023 1024- **stats_timer**: 1025 To calculate the SocketCAN core statistics 1026 (e.g. current/maximum frames per second) this 1 second timer is 1027 invoked at can.ko module start time by default. This timer can be 1028 disabled by using stattimer=0 on the module commandline. 1029 1030- **debug**: 1031 (removed since SocketCAN SVN r546) 1032 1033 1034procfs content 1035-------------- 1036 1037As described in :ref:`socketcan-receive-lists` the SocketCAN core uses several filter 1038lists to deliver received CAN frames to CAN protocol modules. These 1039receive lists, their filters and the count of filter matches can be 1040checked in the appropriate receive list. All entries contain the 1041device and a protocol module identifier:: 1042 1043 foo@bar:~$ cat /proc/net/can/rcvlist_all 1044 1045 receive list 'rx_all': 1046 (vcan3: no entry) 1047 (vcan2: no entry) 1048 (vcan1: no entry) 1049 device can_id can_mask function userdata matches ident 1050 vcan0 000 00000000 f88e6370 f6c6f400 0 raw 1051 (any: no entry) 1052 1053In this example an application requests any CAN traffic from vcan0:: 1054 1055 rcvlist_all - list for unfiltered entries (no filter operations) 1056 rcvlist_eff - list for single extended frame (EFF) entries 1057 rcvlist_err - list for error message frames masks 1058 rcvlist_fil - list for mask/value filters 1059 rcvlist_inv - list for mask/value filters (inverse semantic) 1060 rcvlist_sff - list for single standard frame (SFF) entries 1061 1062Additional procfs files in /proc/net/can:: 1063 1064 stats - SocketCAN core statistics (rx/tx frames, match ratios, ...) 1065 reset_stats - manual statistic reset 1066 version - prints SocketCAN core and ABI version (removed in Linux 5.10) 1067 1068 1069Writing Own CAN Protocol Modules 1070-------------------------------- 1071 1072To implement a new protocol in the protocol family PF_CAN a new 1073protocol has to be defined in include/linux/can.h . 1074The prototypes and definitions to use the SocketCAN core can be 1075accessed by including include/linux/can/core.h . 1076In addition to functions that register the CAN protocol and the 1077CAN device notifier chain there are functions to subscribe CAN 1078frames received by CAN interfaces and to send CAN frames:: 1079 1080 can_rx_register - subscribe CAN frames from a specific interface 1081 can_rx_unregister - unsubscribe CAN frames from a specific interface 1082 can_send - transmit a CAN frame (optional with local loopback) 1083 1084For details see the kerneldoc documentation in net/can/af_can.c or 1085the source code of net/can/raw.c or net/can/bcm.c . 1086 1087 1088CAN Network Drivers 1089=================== 1090 1091Writing a CAN network device driver is much easier than writing a 1092CAN character device driver. Similar to other known network device 1093drivers you mainly have to deal with: 1094 1095- TX: Put the CAN frame from the socket buffer to the CAN controller. 1096- RX: Put the CAN frame from the CAN controller to the socket buffer. 1097 1098See e.g. at Documentation/networking/netdevices.rst . The differences 1099for writing CAN network device driver are described below: 1100 1101 1102General Settings 1103---------------- 1104 1105.. code-block:: C 1106 1107 dev->type = ARPHRD_CAN; /* the netdevice hardware type */ 1108 dev->flags = IFF_NOARP; /* CAN has no arp */ 1109 1110 dev->mtu = CAN_MTU; /* sizeof(struct can_frame) -> Classical CAN interface */ 1111 1112 or alternative, when the controller supports CAN with flexible data rate: 1113 dev->mtu = CANFD_MTU; /* sizeof(struct canfd_frame) -> CAN FD interface */ 1114 1115The struct can_frame or struct canfd_frame is the payload of each socket 1116buffer (skbuff) in the protocol family PF_CAN. 1117 1118 1119.. _socketcan-local-loopback2: 1120 1121Local Loopback of Sent Frames 1122----------------------------- 1123 1124As described in :ref:`socketcan-local-loopback1` the CAN network device driver should 1125support a local loopback functionality similar to the local echo 1126e.g. of tty devices. In this case the driver flag IFF_ECHO has to be 1127set to prevent the PF_CAN core from locally echoing sent frames 1128(aka loopback) as fallback solution:: 1129 1130 dev->flags = (IFF_NOARP | IFF_ECHO); 1131 1132 1133CAN Controller Hardware Filters 1134------------------------------- 1135 1136To reduce the interrupt load on deep embedded systems some CAN 1137controllers support the filtering of CAN IDs or ranges of CAN IDs. 1138These hardware filter capabilities vary from controller to 1139controller and have to be identified as not feasible in a multi-user 1140networking approach. The use of the very controller specific 1141hardware filters could make sense in a very dedicated use-case, as a 1142filter on driver level would affect all users in the multi-user 1143system. The high efficient filter sets inside the PF_CAN core allow 1144to set different multiple filters for each socket separately. 1145Therefore the use of hardware filters goes to the category 'handmade 1146tuning on deep embedded systems'. The author is running a MPC603e 1147@133MHz with four SJA1000 CAN controllers from 2002 under heavy bus 1148load without any problems ... 1149 1150 1151Switchable Termination Resistors 1152-------------------------------- 1153 1154CAN bus requires a specific impedance across the differential pair, 1155typically provided by two 120Ohm resistors on the farthest nodes of 1156the bus. Some CAN controllers support activating / deactivating a 1157termination resistor(s) to provide the correct impedance. 1158 1159Query the available resistances:: 1160 1161 $ ip -details link show can0 1162 ... 1163 termination 120 [ 0, 120 ] 1164 1165Activate the terminating resistor:: 1166 1167 $ ip link set dev can0 type can termination 120 1168 1169Deactivate the terminating resistor:: 1170 1171 $ ip link set dev can0 type can termination 0 1172 1173To enable termination resistor support to a can-controller, either 1174implement in the controller's struct can-priv:: 1175 1176 termination_const 1177 termination_const_cnt 1178 do_set_termination 1179 1180or add gpio control with the device tree entries from 1181Documentation/devicetree/bindings/net/can/can-controller.yaml 1182 1183 1184The Virtual CAN Driver (vcan) 1185----------------------------- 1186 1187Similar to the network loopback devices, vcan offers a virtual local 1188CAN interface. A full qualified address on CAN consists of 1189 1190- a unique CAN Identifier (CAN ID) 1191- the CAN bus this CAN ID is transmitted on (e.g. can0) 1192 1193so in common use cases more than one virtual CAN interface is needed. 1194 1195The virtual CAN interfaces allow the transmission and reception of CAN 1196frames without real CAN controller hardware. Virtual CAN network 1197devices are usually named 'vcanX', like vcan0 vcan1 vcan2 ... 1198When compiled as a module the virtual CAN driver module is called vcan.ko 1199 1200Since Linux Kernel version 2.6.24 the vcan driver supports the Kernel 1201netlink interface to create vcan network devices. The creation and 1202removal of vcan network devices can be managed with the ip(8) tool:: 1203 1204 - Create a virtual CAN network interface: 1205 $ ip link add type vcan 1206 1207 - Create a virtual CAN network interface with a specific name 'vcan42': 1208 $ ip link add dev vcan42 type vcan 1209 1210 - Remove a (virtual CAN) network interface 'vcan42': 1211 $ ip link del vcan42 1212 1213 1214The CAN Network Device Driver Interface 1215--------------------------------------- 1216 1217The CAN network device driver interface provides a generic interface 1218to setup, configure and monitor CAN network devices. The user can then 1219configure the CAN device, like setting the bit-timing parameters, via 1220the netlink interface using the program "ip" from the "IPROUTE2" 1221utility suite. The following chapter describes briefly how to use it. 1222Furthermore, the interface uses a common data structure and exports a 1223set of common functions, which all real CAN network device drivers 1224should use. Please have a look to the SJA1000 or MSCAN driver to 1225understand how to use them. The name of the module is can-dev.ko. 1226 1227 1228Netlink interface to set/get devices properties 1229~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1230 1231The CAN device must be configured via netlink interface. The supported 1232netlink message types are defined and briefly described in 1233"include/linux/can/netlink.h". CAN link support for the program "ip" 1234of the IPROUTE2 utility suite is available and it can be used as shown 1235below: 1236 1237Setting CAN device properties:: 1238 1239 $ ip link set can0 type can help 1240 Usage: ip link set DEVICE type can 1241 [ bitrate BITRATE [ sample-point SAMPLE-POINT] ] | 1242 [ tq TQ prop-seg PROP_SEG phase-seg1 PHASE-SEG1 1243 phase-seg2 PHASE-SEG2 [ sjw SJW ] ] 1244 1245 [ dbitrate BITRATE [ dsample-point SAMPLE-POINT] ] | 1246 [ dtq TQ dprop-seg PROP_SEG dphase-seg1 PHASE-SEG1 1247 dphase-seg2 PHASE-SEG2 [ dsjw SJW ] ] 1248 1249 [ loopback { on | off } ] 1250 [ listen-only { on | off } ] 1251 [ triple-sampling { on | off } ] 1252 [ one-shot { on | off } ] 1253 [ berr-reporting { on | off } ] 1254 [ fd { on | off } ] 1255 [ fd-non-iso { on | off } ] 1256 [ presume-ack { on | off } ] 1257 [ cc-len8-dlc { on | off } ] 1258 1259 [ restart-ms TIME-MS ] 1260 [ restart ] 1261 1262 Where: BITRATE := { 1..1000000 } 1263 SAMPLE-POINT := { 0.000..0.999 } 1264 TQ := { NUMBER } 1265 PROP-SEG := { 1..8 } 1266 PHASE-SEG1 := { 1..8 } 1267 PHASE-SEG2 := { 1..8 } 1268 SJW := { 1..4 } 1269 RESTART-MS := { 0 | NUMBER } 1270 1271Display CAN device details and statistics:: 1272 1273 $ ip -details -statistics link show can0 1274 2: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UP qlen 10 1275 link/can 1276 can <TRIPLE-SAMPLING> state ERROR-ACTIVE restart-ms 100 1277 bitrate 125000 sample_point 0.875 1278 tq 125 prop-seg 6 phase-seg1 7 phase-seg2 2 sjw 1 1279 sja1000: tseg1 1..16 tseg2 1..8 sjw 1..4 brp 1..64 brp-inc 1 1280 clock 8000000 1281 re-started bus-errors arbit-lost error-warn error-pass bus-off 1282 41 17457 0 41 42 41 1283 RX: bytes packets errors dropped overrun mcast 1284 140859 17608 17457 0 0 0 1285 TX: bytes packets errors dropped carrier collsns 1286 861 112 0 41 0 0 1287 1288More info to the above output: 1289 1290"<TRIPLE-SAMPLING>" 1291 Shows the list of selected CAN controller modes: LOOPBACK, 1292 LISTEN-ONLY, or TRIPLE-SAMPLING. 1293 1294"state ERROR-ACTIVE" 1295 The current state of the CAN controller: "ERROR-ACTIVE", 1296 "ERROR-WARNING", "ERROR-PASSIVE", "BUS-OFF" or "STOPPED" 1297 1298"restart-ms 100" 1299 Automatic restart delay time. If set to a non-zero value, a 1300 restart of the CAN controller will be triggered automatically 1301 in case of a bus-off condition after the specified delay time 1302 in milliseconds. By default it's off. 1303 1304"bitrate 125000 sample-point 0.875" 1305 Shows the real bit-rate in bits/sec and the sample-point in the 1306 range 0.000..0.999. If the calculation of bit-timing parameters 1307 is enabled in the kernel (CONFIG_CAN_CALC_BITTIMING=y), the 1308 bit-timing can be defined by setting the "bitrate" argument. 1309 Optionally the "sample-point" can be specified. By default it's 1310 0.000 assuming CIA-recommended sample-points. 1311 1312"tq 125 prop-seg 6 phase-seg1 7 phase-seg2 2 sjw 1" 1313 Shows the time quanta in ns, propagation segment, phase buffer 1314 segment 1 and 2 and the synchronisation jump width in units of 1315 tq. They allow to define the CAN bit-timing in a hardware 1316 independent format as proposed by the Bosch CAN 2.0 spec (see 1317 chapter 8 of http://www.semiconductors.bosch.de/pdf/can2spec.pdf). 1318 1319"sja1000: tseg1 1..16 tseg2 1..8 sjw 1..4 brp 1..64 brp-inc 1 clock 8000000" 1320 Shows the bit-timing constants of the CAN controller, here the 1321 "sja1000". The minimum and maximum values of the time segment 1 1322 and 2, the synchronisation jump width in units of tq, the 1323 bitrate pre-scaler and the CAN system clock frequency in Hz. 1324 These constants could be used for user-defined (non-standard) 1325 bit-timing calculation algorithms in user-space. 1326 1327"re-started bus-errors arbit-lost error-warn error-pass bus-off" 1328 Shows the number of restarts, bus and arbitration lost errors, 1329 and the state changes to the error-warning, error-passive and 1330 bus-off state. RX overrun errors are listed in the "overrun" 1331 field of the standard network statistics. 1332 1333Setting the CAN Bit-Timing 1334~~~~~~~~~~~~~~~~~~~~~~~~~~ 1335 1336The CAN bit-timing parameters can always be defined in a hardware 1337independent format as proposed in the Bosch CAN 2.0 specification 1338specifying the arguments "tq", "prop_seg", "phase_seg1", "phase_seg2" 1339and "sjw":: 1340 1341 $ ip link set canX type can tq 125 prop-seg 6 \ 1342 phase-seg1 7 phase-seg2 2 sjw 1 1343 1344If the kernel option CONFIG_CAN_CALC_BITTIMING is enabled, CIA 1345recommended CAN bit-timing parameters will be calculated if the bit- 1346rate is specified with the argument "bitrate":: 1347 1348 $ ip link set canX type can bitrate 125000 1349 1350Note that this works fine for the most common CAN controllers with 1351standard bit-rates but may *fail* for exotic bit-rates or CAN system 1352clock frequencies. Disabling CONFIG_CAN_CALC_BITTIMING saves some 1353space and allows user-space tools to solely determine and set the 1354bit-timing parameters. The CAN controller specific bit-timing 1355constants can be used for that purpose. They are listed by the 1356following command:: 1357 1358 $ ip -details link show can0 1359 ... 1360 sja1000: clock 8000000 tseg1 1..16 tseg2 1..8 sjw 1..4 brp 1..64 brp-inc 1 1361 1362 1363Starting and Stopping the CAN Network Device 1364~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1365 1366A CAN network device is started or stopped as usual with the command 1367"ifconfig canX up/down" or "ip link set canX up/down". Be aware that 1368you *must* define proper bit-timing parameters for real CAN devices 1369before you can start it to avoid error-prone default settings:: 1370 1371 $ ip link set canX up type can bitrate 125000 1372 1373A device may enter the "bus-off" state if too many errors occurred on 1374the CAN bus. Then no more messages are received or sent. An automatic 1375bus-off recovery can be enabled by setting the "restart-ms" to a 1376non-zero value, e.g.:: 1377 1378 $ ip link set canX type can restart-ms 100 1379 1380Alternatively, the application may realize the "bus-off" condition 1381by monitoring CAN error message frames and do a restart when 1382appropriate with the command:: 1383 1384 $ ip link set canX type can restart 1385 1386Note that a restart will also create a CAN error message frame (see 1387also :ref:`socketcan-network-problem-notifications`). 1388 1389 1390.. _socketcan-can-fd-driver: 1391 1392CAN FD (Flexible Data Rate) Driver Support 1393------------------------------------------ 1394 1395CAN FD capable CAN controllers support two different bitrates for the 1396arbitration phase and the payload phase of the CAN FD frame. Therefore a 1397second bit timing has to be specified in order to enable the CAN FD bitrate. 1398 1399Additionally CAN FD capable CAN controllers support up to 64 bytes of 1400payload. The representation of this length in can_frame.len and 1401canfd_frame.len for userspace applications and inside the Linux network 1402layer is a plain value from 0 .. 64 instead of the CAN 'data length code'. 1403The data length code was a 1:1 mapping to the payload length in the Classical 1404CAN frames anyway. The payload length to the bus-relevant DLC mapping is 1405only performed inside the CAN drivers, preferably with the helper 1406functions can_fd_dlc2len() and can_fd_len2dlc(). 1407 1408The CAN netdevice driver capabilities can be distinguished by the network 1409devices maximum transfer unit (MTU):: 1410 1411 MTU = 16 (CAN_MTU) => sizeof(struct can_frame) => Classical CAN device 1412 MTU = 72 (CANFD_MTU) => sizeof(struct canfd_frame) => CAN FD capable device 1413 1414The CAN device MTU can be retrieved e.g. with a SIOCGIFMTU ioctl() syscall. 1415N.B. CAN FD capable devices can also handle and send Classical CAN frames. 1416 1417When configuring CAN FD capable CAN controllers an additional 'data' bitrate 1418has to be set. This bitrate for the data phase of the CAN FD frame has to be 1419at least the bitrate which was configured for the arbitration phase. This 1420second bitrate is specified analogue to the first bitrate but the bitrate 1421setting keywords for the 'data' bitrate start with 'd' e.g. dbitrate, 1422dsample-point, dsjw or dtq and similar settings. When a data bitrate is set 1423within the configuration process the controller option "fd on" can be 1424specified to enable the CAN FD mode in the CAN controller. This controller 1425option also switches the device MTU to 72 (CANFD_MTU). 1426 1427The first CAN FD specification presented as whitepaper at the International 1428CAN Conference 2012 needed to be improved for data integrity reasons. 1429Therefore two CAN FD implementations have to be distinguished today: 1430 1431- ISO compliant: The ISO 11898-1:2015 CAN FD implementation (default) 1432- non-ISO compliant: The CAN FD implementation following the 2012 whitepaper 1433 1434Finally there are three types of CAN FD controllers: 1435 14361. ISO compliant (fixed) 14372. non-ISO compliant (fixed, like the M_CAN IP core v3.0.1 in m_can.c) 14383. ISO/non-ISO CAN FD controllers (switchable, like the PEAK PCAN-USB FD) 1439 1440The current ISO/non-ISO mode is announced by the CAN controller driver via 1441netlink and displayed by the 'ip' tool (controller option FD-NON-ISO). 1442The ISO/non-ISO-mode can be altered by setting 'fd-non-iso {on|off}' for 1443switchable CAN FD controllers only. 1444 1445Example configuring 500 kbit/s arbitration bitrate and 4 Mbit/s data bitrate:: 1446 1447 $ ip link set can0 up type can bitrate 500000 sample-point 0.75 \ 1448 dbitrate 4000000 dsample-point 0.8 fd on 1449 $ ip -details link show can0 1450 5: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 72 qdisc pfifo_fast state UNKNOWN \ 1451 mode DEFAULT group default qlen 10 1452 link/can promiscuity 0 1453 can <FD> state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0 1454 bitrate 500000 sample-point 0.750 1455 tq 50 prop-seg 14 phase-seg1 15 phase-seg2 10 sjw 1 1456 pcan_usb_pro_fd: tseg1 1..64 tseg2 1..16 sjw 1..16 brp 1..1024 \ 1457 brp-inc 1 1458 dbitrate 4000000 dsample-point 0.800 1459 dtq 12 dprop-seg 7 dphase-seg1 8 dphase-seg2 4 dsjw 1 1460 pcan_usb_pro_fd: dtseg1 1..16 dtseg2 1..8 dsjw 1..4 dbrp 1..1024 \ 1461 dbrp-inc 1 1462 clock 80000000 1463 1464Example when 'fd-non-iso on' is added on this switchable CAN FD adapter:: 1465 1466 can <FD,FD-NON-ISO> state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0 1467 1468 1469Supported CAN Hardware 1470---------------------- 1471 1472Please check the "Kconfig" file in "drivers/net/can" to get an actual 1473list of the support CAN hardware. On the SocketCAN project website 1474(see :ref:`socketcan-resources`) there might be further drivers available, also for 1475older kernel versions. 1476 1477 1478.. _socketcan-resources: 1479 1480SocketCAN Resources 1481=================== 1482 1483The Linux CAN / SocketCAN project resources (project site / mailing list) 1484are referenced in the MAINTAINERS file in the Linux source tree. 1485Search for CAN NETWORK [LAYERS|DRIVERS]. 1486 1487Credits 1488======= 1489 1490- Oliver Hartkopp (PF_CAN core, filters, drivers, bcm, SJA1000 driver) 1491- Urs Thuermann (PF_CAN core, kernel integration, socket interfaces, raw, vcan) 1492- Jan Kizka (RT-SocketCAN core, Socket-API reconciliation) 1493- Wolfgang Grandegger (RT-SocketCAN core & drivers, Raw Socket-API reviews, CAN device driver interface, MSCAN driver) 1494- Robert Schwebel (design reviews, PTXdist integration) 1495- Marc Kleine-Budde (design reviews, Kernel 2.6 cleanups, drivers) 1496- Benedikt Spranger (reviews) 1497- Thomas Gleixner (LKML reviews, coding style, posting hints) 1498- Andrey Volkov (kernel subtree structure, ioctls, MSCAN driver) 1499- Matthias Brukner (first SJA1000 CAN netdevice implementation Q2/2003) 1500- Klaus Hitschler (PEAK driver integration) 1501- Uwe Koppe (CAN netdevices with PF_PACKET approach) 1502- Michael Schulze (driver layer loopback requirement, RT CAN drivers review) 1503- Pavel Pisa (Bit-timing calculation) 1504- Sascha Hauer (SJA1000 platform driver) 1505- Sebastian Haas (SJA1000 EMS PCI driver) 1506- Markus Plessing (SJA1000 EMS PCI driver) 1507- Per Dalen (SJA1000 Kvaser PCI driver) 1508- Sam Ravnborg (reviews, coding style, kbuild help) 1509