1======================================
2Pulse Width Modulation (PWM) interface
3======================================
4
5This provides an overview about the Linux PWM interface
6
7PWMs are commonly used for controlling LEDs, fans or vibrators in
8cell phones. PWMs with a fixed purpose have no need implementing
9the Linux PWM API (although they could). However, PWMs are often
10found as discrete devices on SoCs which have no fixed purpose. It's
11up to the board designer to connect them to LEDs or fans. To provide
12this kind of flexibility the generic PWM API exists.
13
14Identifying PWMs
15----------------
16
17Users of the legacy PWM API use unique IDs to refer to PWM devices.
18
19Instead of referring to a PWM device via its unique ID, board setup code
20should instead register a static mapping that can be used to match PWM
21consumers to providers, as given in the following example::
22
23	static struct pwm_lookup board_pwm_lookup[] = {
24		PWM_LOOKUP("tegra-pwm", 0, "pwm-backlight", NULL,
25			   50000, PWM_POLARITY_NORMAL),
26	};
27
28	static void __init board_init(void)
29	{
30		...
31		pwm_add_table(board_pwm_lookup, ARRAY_SIZE(board_pwm_lookup));
32		...
33	}
34
35Using PWMs
36----------
37
38Legacy users can request a PWM device using pwm_request() and free it
39after usage with pwm_free().
40
41New users should use the pwm_get() function and pass to it the consumer
42device or a consumer name. pwm_put() is used to free the PWM device. Managed
43variants of these functions, devm_pwm_get() and devm_pwm_put(), also exist.
44
45After being requested, a PWM has to be configured using::
46
47	int pwm_apply_state(struct pwm_device *pwm, struct pwm_state *state);
48
49This API controls both the PWM period/duty_cycle config and the
50enable/disable state.
51
52The pwm_config(), pwm_enable() and pwm_disable() functions are just wrappers
53around pwm_apply_state() and should not be used if the user wants to change
54several parameter at once. For example, if you see pwm_config() and
55pwm_{enable,disable}() calls in the same function, this probably means you
56should switch to pwm_apply_state().
57
58The PWM user API also allows one to query the PWM state with pwm_get_state().
59
60In addition to the PWM state, the PWM API also exposes PWM arguments, which
61are the reference PWM config one should use on this PWM.
62PWM arguments are usually platform-specific and allows the PWM user to only
63care about dutycycle relatively to the full period (like, duty = 50% of the
64period). struct pwm_args contains 2 fields (period and polarity) and should
65be used to set the initial PWM config (usually done in the probe function
66of the PWM user). PWM arguments are retrieved with pwm_get_args().
67
68All consumers should really be reconfiguring the PWM upon resume as
69appropriate. This is the only way to ensure that everything is resumed in
70the proper order.
71
72Using PWMs with the sysfs interface
73-----------------------------------
74
75If CONFIG_SYSFS is enabled in your kernel configuration a simple sysfs
76interface is provided to use the PWMs from userspace. It is exposed at
77/sys/class/pwm/. Each probed PWM controller/chip will be exported as
78pwmchipN, where N is the base of the PWM chip. Inside the directory you
79will find:
80
81  npwm
82    The number of PWM channels this chip supports (read-only).
83
84  export
85    Exports a PWM channel for use with sysfs (write-only).
86
87  unexport
88   Unexports a PWM channel from sysfs (write-only).
89
90The PWM channels are numbered using a per-chip index from 0 to npwm-1.
91
92When a PWM channel is exported a pwmX directory will be created in the
93pwmchipN directory it is associated with, where X is the number of the
94channel that was exported. The following properties will then be available:
95
96  period
97    The total period of the PWM signal (read/write).
98    Value is in nanoseconds and is the sum of the active and inactive
99    time of the PWM.
100
101  duty_cycle
102    The active time of the PWM signal (read/write).
103    Value is in nanoseconds and must be less than the period.
104
105  polarity
106    Changes the polarity of the PWM signal (read/write).
107    Writes to this property only work if the PWM chip supports changing
108    the polarity. The polarity can only be changed if the PWM is not
109    enabled. Value is the string "normal" or "inversed".
110
111  enable
112    Enable/disable the PWM signal (read/write).
113
114	- 0 - disabled
115	- 1 - enabled
116
117Implementing a PWM driver
118-------------------------
119
120Currently there are two ways to implement pwm drivers. Traditionally
121there only has been the barebone API meaning that each driver has
122to implement the pwm_*() functions itself. This means that it's impossible
123to have multiple PWM drivers in the system. For this reason it's mandatory
124for new drivers to use the generic PWM framework.
125
126A new PWM controller/chip can be added using pwmchip_add() and removed
127again with pwmchip_remove(). pwmchip_add() takes a filled in struct
128pwm_chip as argument which provides a description of the PWM chip, the
129number of PWM devices provided by the chip and the chip-specific
130implementation of the supported PWM operations to the framework.
131
132When implementing polarity support in a PWM driver, make sure to respect the
133signal conventions in the PWM framework. By definition, normal polarity
134characterizes a signal starts high for the duration of the duty cycle and
135goes low for the remainder of the period. Conversely, a signal with inversed
136polarity starts low for the duration of the duty cycle and goes high for the
137remainder of the period.
138
139Drivers are encouraged to implement ->apply() instead of the legacy
140->enable(), ->disable() and ->config() methods. Doing that should provide
141atomicity in the PWM config workflow, which is required when the PWM controls
142a critical device (like a regulator).
143
144The implementation of ->get_state() (a method used to retrieve initial PWM
145state) is also encouraged for the same reason: letting the PWM user know
146about the current PWM state would allow him to avoid glitches.
147
148Drivers should not implement any power management. In other words,
149consumers should implement it as described in the "Using PWMs" section.
150
151Locking
152-------
153
154The PWM core list manipulations are protected by a mutex, so pwm_request()
155and pwm_free() may not be called from an atomic context. Currently the
156PWM core does not enforce any locking to pwm_enable(), pwm_disable() and
157pwm_config(), so the calling context is currently driver specific. This
158is an issue derived from the former barebone API and should be fixed soon.
159
160Helpers
161-------
162
163Currently a PWM can only be configured with period_ns and duty_ns. For several
164use cases freq_hz and duty_percent might be better. Instead of calculating
165this in your driver please consider adding appropriate helpers to the framework.
166