1============
2Introduction
3============
4
5
6GPIO Interfaces
7===============
8
9The documents in this directory give detailed instructions on how to access
10GPIOs in drivers, and how to write a driver for a device that provides GPIOs
11itself.
12
13Due to the history of GPIO interfaces in the kernel, there are two different
14ways to obtain and use GPIOs:
15
16  - The descriptor-based interface is the preferred way to manipulate GPIOs,
17    and is described by all the files in this directory excepted gpio-legacy.txt.
18  - The legacy integer-based interface which is considered deprecated (but still
19    usable for compatibility reasons) is documented in gpio-legacy.txt.
20
21The remainder of this document applies to the new descriptor-based interface.
22gpio-legacy.txt contains the same information applied to the legacy
23integer-based interface.
24
25
26What is a GPIO?
27===============
28
29A "General Purpose Input/Output" (GPIO) is a flexible software-controlled
30digital signal. They are provided from many kinds of chip, and are familiar
31to Linux developers working with embedded and custom hardware. Each GPIO
32represents a bit connected to a particular pin, or "ball" on Ball Grid Array
33(BGA) packages. Board schematics show which external hardware connects to
34which GPIOs. Drivers can be written generically, so that board setup code
35passes such pin configuration data to drivers.
36
37System-on-Chip (SOC) processors heavily rely on GPIOs. In some cases, every
38non-dedicated pin can be configured as a GPIO; and most chips have at least
39several dozen of them. Programmable logic devices (like FPGAs) can easily
40provide GPIOs; multifunction chips like power managers, and audio codecs
41often have a few such pins to help with pin scarcity on SOCs; and there are
42also "GPIO Expander" chips that connect using the I2C or SPI serial buses.
43Most PC southbridges have a few dozen GPIO-capable pins (with only the BIOS
44firmware knowing how they're used).
45
46The exact capabilities of GPIOs vary between systems. Common options:
47
48  - Output values are writable (high=1, low=0). Some chips also have
49    options about how that value is driven, so that for example only one
50    value might be driven, supporting "wire-OR" and similar schemes for the
51    other value (notably, "open drain" signaling).
52
53  - Input values are likewise readable (1, 0). Some chips support readback
54    of pins configured as "output", which is very useful in such "wire-OR"
55    cases (to support bidirectional signaling). GPIO controllers may have
56    input de-glitch/debounce logic, sometimes with software controls.
57
58  - Inputs can often be used as IRQ signals, often edge triggered but
59    sometimes level triggered. Such IRQs may be configurable as system
60    wakeup events, to wake the system from a low power state.
61
62  - Usually a GPIO will be configurable as either input or output, as needed
63    by different product boards; single direction ones exist too.
64
65  - Most GPIOs can be accessed while holding spinlocks, but those accessed
66    through a serial bus normally can't. Some systems support both types.
67
68On a given board each GPIO is used for one specific purpose like monitoring
69MMC/SD card insertion/removal, detecting card write-protect status, driving
70a LED, configuring a transceiver, bit-banging a serial bus, poking a hardware
71watchdog, sensing a switch, and so on.
72
73
74Common GPIO Properties
75======================
76
77These properties are met through all the other documents of the GPIO interface
78and it is useful to understand them, especially if you need to define GPIO
79mappings.
80
81Active-High and Active-Low
82--------------------------
83It is natural to assume that a GPIO is "active" when its output signal is 1
84("high"), and inactive when it is 0 ("low"). However in practice the signal of a
85GPIO may be inverted before is reaches its destination, or a device could decide
86to have different conventions about what "active" means. Such decisions should
87be transparent to device drivers, therefore it is possible to define a GPIO as
88being either active-high ("1" means "active", the default) or active-low ("0"
89means "active") so that drivers only need to worry about the logical signal and
90not about what happens at the line level.
91
92Open Drain and Open Source
93--------------------------
94Sometimes shared signals need to use "open drain" (where only the low signal
95level is actually driven), or "open source" (where only the high signal level is
96driven) signaling. That term applies to CMOS transistors; "open collector" is
97used for TTL. A pullup or pulldown resistor causes the high or low signal level.
98This is sometimes called a "wire-AND"; or more practically, from the negative
99logic (low=true) perspective this is a "wire-OR".
100
101One common example of an open drain signal is a shared active-low IRQ line.
102Also, bidirectional data bus signals sometimes use open drain signals.
103
104Some GPIO controllers directly support open drain and open source outputs; many
105don't. When you need open drain signaling but your hardware doesn't directly
106support it, there's a common idiom you can use to emulate it with any GPIO pin
107that can be used as either an input or an output:
108
109 LOW:	gpiod_direction_output(gpio, 0) ... this drives the signal and overrides
110	the pullup.
111
112 HIGH:	gpiod_direction_input(gpio) ... this turns off the output, so the pullup
113	(or some other device) controls the signal.
114
115The same logic can be applied to emulate open source signaling, by driving the
116high signal and configuring the GPIO as input for low. This open drain/open
117source emulation can be handled transparently by the GPIO framework.
118
119If you are "driving" the signal high but gpiod_get_value(gpio) reports a low
120value (after the appropriate rise time passes), you know some other component is
121driving the shared signal low. That's not necessarily an error. As one common
122example, that's how I2C clocks are stretched:  a slave that needs a slower clock
123delays the rising edge of SCK, and the I2C master adjusts its signaling rate
124accordingly.
125