1================================== 2GPIO Descriptor Consumer Interface 3================================== 4 5This document describes the consumer interface of the GPIO framework. Note that 6it describes the new descriptor-based interface. For a description of the 7deprecated integer-based GPIO interface please refer to gpio-legacy.txt. 8 9 10Guidelines for GPIOs consumers 11============================== 12 13Drivers that can't work without standard GPIO calls should have Kconfig entries 14that depend on GPIOLIB or select GPIOLIB. The functions that allow a driver to 15obtain and use GPIOs are available by including the following file:: 16 17 #include <linux/gpio/consumer.h> 18 19There are static inline stubs for all functions in the header file in the case 20where GPIOLIB is disabled. When these stubs are called they will emit 21warnings. These stubs are used for two use cases: 22 23- Simple compile coverage with e.g. COMPILE_TEST - it does not matter that 24 the current platform does not enable or select GPIOLIB because we are not 25 going to execute the system anyway. 26 27- Truly optional GPIOLIB support - where the driver does not really make use 28 of the GPIOs on certain compile-time configurations for certain systems, but 29 will use it under other compile-time configurations. In this case the 30 consumer must make sure not to call into these functions, or the user will 31 be met with console warnings that may be perceived as intimidating. 32 33All the functions that work with the descriptor-based GPIO interface are 34prefixed with ``gpiod_``. The ``gpio_`` prefix is used for the legacy 35interface. No other function in the kernel should use these prefixes. The use 36of the legacy functions is strongly discouraged, new code should use 37<linux/gpio/consumer.h> and descriptors exclusively. 38 39 40Obtaining and Disposing GPIOs 41============================= 42 43With the descriptor-based interface, GPIOs are identified with an opaque, 44non-forgeable handler that must be obtained through a call to one of the 45gpiod_get() functions. Like many other kernel subsystems, gpiod_get() takes the 46device that will use the GPIO and the function the requested GPIO is supposed to 47fulfill:: 48 49 struct gpio_desc *gpiod_get(struct device *dev, const char *con_id, 50 enum gpiod_flags flags) 51 52If a function is implemented by using several GPIOs together (e.g. a simple LED 53device that displays digits), an additional index argument can be specified:: 54 55 struct gpio_desc *gpiod_get_index(struct device *dev, 56 const char *con_id, unsigned int idx, 57 enum gpiod_flags flags) 58 59For a more detailed description of the con_id parameter in the DeviceTree case 60see Documentation/driver-api/gpio/board.rst 61 62The flags parameter is used to optionally specify a direction and initial value 63for the GPIO. Values can be: 64 65* GPIOD_ASIS or 0 to not initialize the GPIO at all. The direction must be set 66 later with one of the dedicated functions. 67* GPIOD_IN to initialize the GPIO as input. 68* GPIOD_OUT_LOW to initialize the GPIO as output with a value of 0. 69* GPIOD_OUT_HIGH to initialize the GPIO as output with a value of 1. 70* GPIOD_OUT_LOW_OPEN_DRAIN same as GPIOD_OUT_LOW but also enforce the line 71 to be electrically used with open drain. 72* GPIOD_OUT_HIGH_OPEN_DRAIN same as GPIOD_OUT_HIGH but also enforce the line 73 to be electrically used with open drain. 74 75The two last flags are used for use cases where open drain is mandatory, such 76as I2C: if the line is not already configured as open drain in the mappings 77(see board.txt), then open drain will be enforced anyway and a warning will be 78printed that the board configuration needs to be updated to match the use case. 79 80Both functions return either a valid GPIO descriptor, or an error code checkable 81with IS_ERR() (they will never return a NULL pointer). -ENOENT will be returned 82if and only if no GPIO has been assigned to the device/function/index triplet, 83other error codes are used for cases where a GPIO has been assigned but an error 84occurred while trying to acquire it. This is useful to discriminate between mere 85errors and an absence of GPIO for optional GPIO parameters. For the common 86pattern where a GPIO is optional, the gpiod_get_optional() and 87gpiod_get_index_optional() functions can be used. These functions return NULL 88instead of -ENOENT if no GPIO has been assigned to the requested function:: 89 90 struct gpio_desc *gpiod_get_optional(struct device *dev, 91 const char *con_id, 92 enum gpiod_flags flags) 93 94 struct gpio_desc *gpiod_get_index_optional(struct device *dev, 95 const char *con_id, 96 unsigned int index, 97 enum gpiod_flags flags) 98 99Note that gpio_get*_optional() functions (and their managed variants), unlike 100the rest of gpiolib API, also return NULL when gpiolib support is disabled. 101This is helpful to driver authors, since they do not need to special case 102-ENOSYS return codes. System integrators should however be careful to enable 103gpiolib on systems that need it. 104 105For a function using multiple GPIOs all of those can be obtained with one call:: 106 107 struct gpio_descs *gpiod_get_array(struct device *dev, 108 const char *con_id, 109 enum gpiod_flags flags) 110 111This function returns a struct gpio_descs which contains an array of 112descriptors. It also contains a pointer to a gpiolib private structure which, 113if passed back to get/set array functions, may speed up I/O proocessing:: 114 115 struct gpio_descs { 116 struct gpio_array *info; 117 unsigned int ndescs; 118 struct gpio_desc *desc[]; 119 } 120 121The following function returns NULL instead of -ENOENT if no GPIOs have been 122assigned to the requested function:: 123 124 struct gpio_descs *gpiod_get_array_optional(struct device *dev, 125 const char *con_id, 126 enum gpiod_flags flags) 127 128Device-managed variants of these functions are also defined:: 129 130 struct gpio_desc *devm_gpiod_get(struct device *dev, const char *con_id, 131 enum gpiod_flags flags) 132 133 struct gpio_desc *devm_gpiod_get_index(struct device *dev, 134 const char *con_id, 135 unsigned int idx, 136 enum gpiod_flags flags) 137 138 struct gpio_desc *devm_gpiod_get_optional(struct device *dev, 139 const char *con_id, 140 enum gpiod_flags flags) 141 142 struct gpio_desc *devm_gpiod_get_index_optional(struct device *dev, 143 const char *con_id, 144 unsigned int index, 145 enum gpiod_flags flags) 146 147 struct gpio_descs *devm_gpiod_get_array(struct device *dev, 148 const char *con_id, 149 enum gpiod_flags flags) 150 151 struct gpio_descs *devm_gpiod_get_array_optional(struct device *dev, 152 const char *con_id, 153 enum gpiod_flags flags) 154 155A GPIO descriptor can be disposed of using the gpiod_put() function:: 156 157 void gpiod_put(struct gpio_desc *desc) 158 159For an array of GPIOs this function can be used:: 160 161 void gpiod_put_array(struct gpio_descs *descs) 162 163It is strictly forbidden to use a descriptor after calling these functions. 164It is also not allowed to individually release descriptors (using gpiod_put()) 165from an array acquired with gpiod_get_array(). 166 167The device-managed variants are, unsurprisingly:: 168 169 void devm_gpiod_put(struct device *dev, struct gpio_desc *desc) 170 171 void devm_gpiod_put_array(struct device *dev, struct gpio_descs *descs) 172 173 174Using GPIOs 175=========== 176 177Setting Direction 178----------------- 179The first thing a driver must do with a GPIO is setting its direction. If no 180direction-setting flags have been given to gpiod_get*(), this is done by 181invoking one of the gpiod_direction_*() functions:: 182 183 int gpiod_direction_input(struct gpio_desc *desc) 184 int gpiod_direction_output(struct gpio_desc *desc, int value) 185 186The return value is zero for success, else a negative errno. It should be 187checked, since the get/set calls don't return errors and since misconfiguration 188is possible. You should normally issue these calls from a task context. However, 189for spinlock-safe GPIOs it is OK to use them before tasking is enabled, as part 190of early board setup. 191 192For output GPIOs, the value provided becomes the initial output value. This 193helps avoid signal glitching during system startup. 194 195A driver can also query the current direction of a GPIO:: 196 197 int gpiod_get_direction(const struct gpio_desc *desc) 198 199This function returns 0 for output, 1 for input, or an error code in case of error. 200 201Be aware that there is no default direction for GPIOs. Therefore, **using a GPIO 202without setting its direction first is illegal and will result in undefined 203behavior!** 204 205 206Spinlock-Safe GPIO Access 207------------------------- 208Most GPIO controllers can be accessed with memory read/write instructions. Those 209don't need to sleep, and can safely be done from inside hard (non-threaded) IRQ 210handlers and similar contexts. 211 212Use the following calls to access GPIOs from an atomic context:: 213 214 int gpiod_get_value(const struct gpio_desc *desc); 215 void gpiod_set_value(struct gpio_desc *desc, int value); 216 217The values are boolean, zero for low, nonzero for high. When reading the value 218of an output pin, the value returned should be what's seen on the pin. That 219won't always match the specified output value, because of issues including 220open-drain signaling and output latencies. 221 222The get/set calls do not return errors because "invalid GPIO" should have been 223reported earlier from gpiod_direction_*(). However, note that not all platforms 224can read the value of output pins; those that can't should always return zero. 225Also, using these calls for GPIOs that can't safely be accessed without sleeping 226(see below) is an error. 227 228 229GPIO Access That May Sleep 230-------------------------- 231Some GPIO controllers must be accessed using message based buses like I2C or 232SPI. Commands to read or write those GPIO values require waiting to get to the 233head of a queue to transmit a command and get its response. This requires 234sleeping, which can't be done from inside IRQ handlers. 235 236Platforms that support this type of GPIO distinguish them from other GPIOs by 237returning nonzero from this call:: 238 239 int gpiod_cansleep(const struct gpio_desc *desc) 240 241To access such GPIOs, a different set of accessors is defined:: 242 243 int gpiod_get_value_cansleep(const struct gpio_desc *desc) 244 void gpiod_set_value_cansleep(struct gpio_desc *desc, int value) 245 246Accessing such GPIOs requires a context which may sleep, for example a threaded 247IRQ handler, and those accessors must be used instead of spinlock-safe 248accessors without the cansleep() name suffix. 249 250Other than the fact that these accessors might sleep, and will work on GPIOs 251that can't be accessed from hardIRQ handlers, these calls act the same as the 252spinlock-safe calls. 253 254 255The active low and open drain semantics 256--------------------------------------- 257As a consumer should not have to care about the physical line level, all of the 258gpiod_set_value_xxx() or gpiod_set_array_value_xxx() functions operate with 259the *logical* value. With this they take the active low property into account. 260This means that they check whether the GPIO is configured to be active low, 261and if so, they manipulate the passed value before the physical line level is 262driven. 263 264The same is applicable for open drain or open source output lines: those do not 265actively drive their output high (open drain) or low (open source), they just 266switch their output to a high impedance value. The consumer should not need to 267care. (For details read about open drain in driver.txt.) 268 269With this, all the gpiod_set_(array)_value_xxx() functions interpret the 270parameter "value" as "asserted" ("1") or "de-asserted" ("0"). The physical line 271level will be driven accordingly. 272 273As an example, if the active low property for a dedicated GPIO is set, and the 274gpiod_set_(array)_value_xxx() passes "asserted" ("1"), the physical line level 275will be driven low. 276 277To summarize:: 278 279 Function (example) line property physical line 280 gpiod_set_raw_value(desc, 0); don't care low 281 gpiod_set_raw_value(desc, 1); don't care high 282 gpiod_set_value(desc, 0); default (active high) low 283 gpiod_set_value(desc, 1); default (active high) high 284 gpiod_set_value(desc, 0); active low high 285 gpiod_set_value(desc, 1); active low low 286 gpiod_set_value(desc, 0); open drain low 287 gpiod_set_value(desc, 1); open drain high impedance 288 gpiod_set_value(desc, 0); open source high impedance 289 gpiod_set_value(desc, 1); open source high 290 291It is possible to override these semantics using the set_raw/get_raw functions 292but it should be avoided as much as possible, especially by system-agnostic drivers 293which should not need to care about the actual physical line level and worry about 294the logical value instead. 295 296 297Accessing raw GPIO values 298------------------------- 299Consumers exist that need to manage the logical state of a GPIO line, i.e. the value 300their device will actually receive, no matter what lies between it and the GPIO 301line. 302 303The following set of calls ignore the active-low or open drain property of a GPIO and 304work on the raw line value:: 305 306 int gpiod_get_raw_value(const struct gpio_desc *desc) 307 void gpiod_set_raw_value(struct gpio_desc *desc, int value) 308 int gpiod_get_raw_value_cansleep(const struct gpio_desc *desc) 309 void gpiod_set_raw_value_cansleep(struct gpio_desc *desc, int value) 310 int gpiod_direction_output_raw(struct gpio_desc *desc, int value) 311 312The active low state of a GPIO can also be queried using the following call:: 313 314 int gpiod_is_active_low(const struct gpio_desc *desc) 315 316Note that these functions should only be used with great moderation; a driver 317should not have to care about the physical line level or open drain semantics. 318 319 320Access multiple GPIOs with a single function call 321------------------------------------------------- 322The following functions get or set the values of an array of GPIOs:: 323 324 int gpiod_get_array_value(unsigned int array_size, 325 struct gpio_desc **desc_array, 326 struct gpio_array *array_info, 327 unsigned long *value_bitmap); 328 int gpiod_get_raw_array_value(unsigned int array_size, 329 struct gpio_desc **desc_array, 330 struct gpio_array *array_info, 331 unsigned long *value_bitmap); 332 int gpiod_get_array_value_cansleep(unsigned int array_size, 333 struct gpio_desc **desc_array, 334 struct gpio_array *array_info, 335 unsigned long *value_bitmap); 336 int gpiod_get_raw_array_value_cansleep(unsigned int array_size, 337 struct gpio_desc **desc_array, 338 struct gpio_array *array_info, 339 unsigned long *value_bitmap); 340 341 int gpiod_set_array_value(unsigned int array_size, 342 struct gpio_desc **desc_array, 343 struct gpio_array *array_info, 344 unsigned long *value_bitmap) 345 int gpiod_set_raw_array_value(unsigned int array_size, 346 struct gpio_desc **desc_array, 347 struct gpio_array *array_info, 348 unsigned long *value_bitmap) 349 int gpiod_set_array_value_cansleep(unsigned int array_size, 350 struct gpio_desc **desc_array, 351 struct gpio_array *array_info, 352 unsigned long *value_bitmap) 353 int gpiod_set_raw_array_value_cansleep(unsigned int array_size, 354 struct gpio_desc **desc_array, 355 struct gpio_array *array_info, 356 unsigned long *value_bitmap) 357 358The array can be an arbitrary set of GPIOs. The functions will try to access 359GPIOs belonging to the same bank or chip simultaneously if supported by the 360corresponding chip driver. In that case a significantly improved performance 361can be expected. If simultaneous access is not possible the GPIOs will be 362accessed sequentially. 363 364The functions take four arguments: 365 366 * array_size - the number of array elements 367 * desc_array - an array of GPIO descriptors 368 * array_info - optional information obtained from gpiod_get_array() 369 * value_bitmap - a bitmap to store the GPIOs' values (get) or 370 a bitmap of values to assign to the GPIOs (set) 371 372The descriptor array can be obtained using the gpiod_get_array() function 373or one of its variants. If the group of descriptors returned by that function 374matches the desired group of GPIOs, those GPIOs can be accessed by simply using 375the struct gpio_descs returned by gpiod_get_array():: 376 377 struct gpio_descs *my_gpio_descs = gpiod_get_array(...); 378 gpiod_set_array_value(my_gpio_descs->ndescs, my_gpio_descs->desc, 379 my_gpio_descs->info, my_gpio_value_bitmap); 380 381It is also possible to access a completely arbitrary array of descriptors. The 382descriptors may be obtained using any combination of gpiod_get() and 383gpiod_get_array(). Afterwards the array of descriptors has to be setup 384manually before it can be passed to one of the above functions. In that case, 385array_info should be set to NULL. 386 387Note that for optimal performance GPIOs belonging to the same chip should be 388contiguous within the array of descriptors. 389 390Still better performance may be achieved if array indexes of the descriptors 391match hardware pin numbers of a single chip. If an array passed to a get/set 392array function matches the one obtained from gpiod_get_array() and array_info 393associated with the array is also passed, the function may take a fast bitmap 394processing path, passing the value_bitmap argument directly to the respective 395.get/set_multiple() callback of the chip. That allows for utilization of GPIO 396banks as data I/O ports without much loss of performance. 397 398The return value of gpiod_get_array_value() and its variants is 0 on success 399or negative on error. Note the difference to gpiod_get_value(), which returns 4000 or 1 on success to convey the GPIO value. With the array functions, the GPIO 401values are stored in value_array rather than passed back as return value. 402 403 404GPIOs mapped to IRQs 405-------------------- 406GPIO lines can quite often be used as IRQs. You can get the IRQ number 407corresponding to a given GPIO using the following call:: 408 409 int gpiod_to_irq(const struct gpio_desc *desc) 410 411It will return an IRQ number, or a negative errno code if the mapping can't be 412done (most likely because that particular GPIO cannot be used as IRQ). It is an 413unchecked error to use a GPIO that wasn't set up as an input using 414gpiod_direction_input(), or to use an IRQ number that didn't originally come 415from gpiod_to_irq(). gpiod_to_irq() is not allowed to sleep. 416 417Non-error values returned from gpiod_to_irq() can be passed to request_irq() or 418free_irq(). They will often be stored into IRQ resources for platform devices, 419by the board-specific initialization code. Note that IRQ trigger options are 420part of the IRQ interface, e.g. IRQF_TRIGGER_FALLING, as are system wakeup 421capabilities. 422 423 424GPIOs and ACPI 425============== 426 427On ACPI systems, GPIOs are described by GpioIo()/GpioInt() resources listed by 428the _CRS configuration objects of devices. Those resources do not provide 429connection IDs (names) for GPIOs, so it is necessary to use an additional 430mechanism for this purpose. 431 432Systems compliant with ACPI 5.1 or newer may provide a _DSD configuration object 433which, among other things, may be used to provide connection IDs for specific 434GPIOs described by the GpioIo()/GpioInt() resources in _CRS. If that is the 435case, it will be handled by the GPIO subsystem automatically. However, if the 436_DSD is not present, the mappings between GpioIo()/GpioInt() resources and GPIO 437connection IDs need to be provided by device drivers. 438 439For details refer to Documentation/firmware-guide/acpi/gpio-properties.rst 440 441 442Interacting With the Legacy GPIO Subsystem 443========================================== 444Many kernel subsystems and drivers still handle GPIOs using the legacy 445integer-based interface. It is strongly recommended to update these to the new 446gpiod interface. For cases where both interfaces need to be used, the following 447two functions allow to convert a GPIO descriptor into the GPIO integer namespace 448and vice-versa:: 449 450 int desc_to_gpio(const struct gpio_desc *desc) 451 struct gpio_desc *gpio_to_desc(unsigned gpio) 452 453The GPIO number returned by desc_to_gpio() can safely be used as a parameter of 454the gpio\_*() functions for as long as the GPIO descriptor `desc` is not freed. 455All the same, a GPIO number passed to gpio_to_desc() must first be properly 456acquired using e.g. gpio_request_one(), and the returned GPIO descriptor is only 457considered valid until that GPIO number is released using gpio_free(). 458 459Freeing a GPIO obtained by one API with the other API is forbidden and an 460unchecked error. 461