1MSM SoC HSUSB controllers
2
3EHCI
4
5Required properties:
6- compatible:	Should contain "qcom,ehci-host"
7- regs:			offset and length of the register set in the memory map
8- usb-phy:		phandle for the PHY device
9
10Example EHCI controller device node:
11
12	ehci: ehci@f9a55000 {
13		compatible = "qcom,ehci-host";
14		reg = <0xf9a55000 0x400>;
15		usb-phy = <&usb_otg>;
16	};
17
18USB PHY with optional OTG:
19
20Required properties:
21- compatible:   Should contain:
22  "qcom,usb-otg-ci" for chipsets with ChipIdea 45nm PHY
23  "qcom,usb-otg-snps" for chipsets with Synopsys 28nm PHY
24
25- regs:         Offset and length of the register set in the memory map
26- interrupts:   interrupt-specifier for the OTG interrupt.
27
28- clocks:       A list of phandle + clock-specifier pairs for the
29                clocks listed in clock-names
30- clock-names:  Should contain the following:
31  "phy"         USB PHY reference clock
32  "core"        Protocol engine clock
33  "iface"       Interface bus clock
34  "alt_core"    Protocol engine clock for targets with asynchronous
35                reset methodology. (optional)
36
37- vdccx-supply: phandle to the regulator for the vdd supply for
38                digital circuit operation.
39- v1p8-supply:  phandle to the regulator for the 1.8V supply
40- v3p3-supply:  phandle to the regulator for the 3.3V supply
41
42- resets:       A list of phandle + reset-specifier pairs for the
43                resets listed in reset-names
44- reset-names:  Should contain the following:
45  "phy"         USB PHY controller reset
46  "link"        USB LINK controller reset
47
48- qcom,otg-control: OTG control (VBUS and ID notifications) can be one of
49                1 - PHY control
50                2 - PMIC control
51
52Optional properties:
53- dr_mode:      One of "host", "peripheral" or "otg". Defaults to "otg"
54
55- switch-gpio:  A phandle + gpio-specifier pair. Some boards are using Dual
56                SPDT USB Switch, witch is controlled by GPIO to de/multiplex
57                D+/D- USB lines between connectors.
58
59- qcom,phy-init-sequence: PHY configuration sequence values. This is related to Device
60                Mode Eye Diagram test. Start address at which these values will be
61                written is ULPI_EXT_VENDOR_SPECIFIC. Value of -1 is reserved as
62                "do not overwrite default value at this address".
63                For example: qcom,phy-init-sequence = < -1 0x63 >;
64                Will update only value at address ULPI_EXT_VENDOR_SPECIFIC + 1.
65
66- qcom,phy-num: Select number of pyco-phy to use, can be one of
67                0 - PHY one, default
68                1 - Second PHY
69                Some platforms may have configuration to allow USB
70                controller work with any of the two HSPHYs present.
71
72- qcom,vdd-levels: This property must be a list of three integer values
73                (no, min, max) where each value represents either a voltage
74                in microvolts or a value corresponding to voltage corner.
75
76- qcom,manual-pullup: If present, vbus is not routed to USB controller/phy
77                and controller driver therefore enables pull-up explicitly
78                before starting controller using usbcmd run/stop bit.
79
80- extcon:       phandles to external connector devices. First phandle
81                should point to external connector, which provide "USB"
82                cable events, the second should point to external connector
83                device, which provide "USB-HOST" cable events. If one of
84                the external connector devices is not required empty <0>
85                phandle should be specified.
86
87Example HSUSB OTG controller device node:
88
89    usb@f9a55000 {
90        compatible = "qcom,usb-otg-snps";
91        reg = <0xf9a55000 0x400>;
92        interrupts = <0 134 0>;
93        dr_mode = "peripheral";
94
95        clocks = <&gcc GCC_XO_CLK>, <&gcc GCC_USB_HS_SYSTEM_CLK>,
96                <&gcc GCC_USB_HS_AHB_CLK>;
97
98        clock-names = "phy", "core", "iface";
99
100        vddcx-supply = <&pm8841_s2_corner>;
101        v1p8-supply = <&pm8941_l6>;
102        v3p3-supply = <&pm8941_l24>;
103
104        resets = <&gcc GCC_USB2A_PHY_BCR>, <&gcc GCC_USB_HS_BCR>;
105        reset-names = "phy", "link";
106
107        qcom,otg-control = <1>;
108        qcom,phy-init-sequence = < -1 0x63 >;
109        qcom,vdd-levels = <1 5 7>;
110	};
111