1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
2# Copyright (c) 2020 MediaTek
3%YAML 1.2
4---
5$id: http://devicetree.org/schemas/usb/mediatek,mtu3.yaml#
6$schema: http://devicetree.org/meta-schemas/core.yaml#
7
8title: MediaTek USB3 DRD Controller
9
10maintainers:
11  - Chunfeng Yun <chunfeng.yun@mediatek.com>
12
13allOf:
14  - $ref: usb-drd.yaml
15
16description: |
17  The DRD controller has a glue layer IPPC (IP Port Control), and its host is
18  based on xHCI.
19
20properties:
21  compatible:
22    items:
23      - enum:
24          - mediatek,mt2712-mtu3
25          - mediatek,mt8173-mtu3
26          - mediatek,mt8183-mtu3
27          - mediatek,mt8186-mtu3
28          - mediatek,mt8188-mtu3
29          - mediatek,mt8192-mtu3
30          - mediatek,mt8195-mtu3
31          - mediatek,mt8365-mtu3
32      - const: mediatek,mtu3
33
34  reg:
35    items:
36      - description: the registers of device MAC
37      - description: the registers of IP Port Control
38
39  reg-names:
40    items:
41      - const: mac
42      - const: ippc
43
44  interrupts:
45    description:
46      use "interrupts-extended" when the interrupts are connected to the
47      separate interrupt controllers
48    minItems: 1
49    items:
50      - description: SSUSB device controller interrupt
51      - description: optional, wakeup interrupt used to support runtime PM
52
53  interrupt-names:
54    items:
55      - const: device
56      - const: wakeup
57
58  power-domains:
59    description: A phandle to USB power domain node to control USB's MTCMOS
60    maxItems: 1
61
62  clocks:
63    minItems: 1
64    items:
65      - description: Controller clock used by normal mode
66      - description: Reference clock used by low power mode etc
67      - description: Mcu bus clock for register access
68      - description: DMA bus clock for data transfer
69      - description: DRD controller clock
70      - description: Frame count clock
71
72  clock-names:
73    minItems: 1
74    items:
75      - const: sys_ck  # required, others are optional
76      - const: ref_ck
77      - const: mcu_ck
78      - const: dma_ck
79      - const: xhci_ck
80      - const: frmcnt_ck
81
82  phys:
83    description:
84      List of all the USB PHYs used, it's better to keep the sequence
85      as the hardware layout.
86    minItems: 1
87    items:
88      - description: USB2/HS PHY    # required, others are optional
89      - description: USB3/SS(P) PHY
90      - description: USB2/HS PHY    # the following for backward compatible
91      - description: USB3/SS(P) PHY
92      - description: USB2/HS PHY
93      - description: USB3/SS(P) PHY
94      - description: USB2/HS PHY
95      - description: USB3/SS(P) PHY
96      - description: USB2/HS PHY
97
98  vusb33-supply:
99    description: Regulator of USB AVDD3.3v
100
101  vbus-supply:
102    deprecated: true
103    description: |
104      Regulator of USB VBUS5v, needed when supports dual-role mode.
105      Particularly, if use an output GPIO to control a VBUS regulator, should
106      model it as a regulator. See bindings/regulator/fixed-regulator.yaml
107      It's considered valid for compatibility reasons, not allowed for
108      new bindings, and put into a usb-connector node.
109
110  dr_mode:
111    enum: [host, peripheral, otg]
112    default: otg
113
114  maximum-speed:
115    enum: [super-speed-plus, super-speed, high-speed, full-speed]
116
117  resets:
118    maxItems: 1
119
120  "#address-cells":
121    enum: [1, 2]
122
123  "#size-cells":
124    enum: [1, 2]
125
126  ranges: true
127
128  extcon:
129    deprecated: true
130    description: |
131      Phandle to the extcon device detecting the IDDIG state, needed
132      when supports dual-role mode.
133      It's considered valid for compatibility reasons, not allowed for
134      new bindings, and use "usb-role-switch" property instead.
135
136  usb-role-switch:
137    $ref: /schemas/types.yaml#/definitions/flag
138    description: Support role switch.
139    type: boolean
140
141  role-switch-default-mode:
142    enum: [host, peripheral]
143    default: host
144
145  connector:
146    $ref: /schemas/connector/usb-connector.yaml#
147    description:
148      Connector for dual role switch, especially for "gpio-usb-b-connector"
149    type: object
150
151  port:
152    description:
153      Any connector to the data bus of this controller should be modelled
154      using the OF graph bindings specified, if the "usb-role-switch"
155      property is used. See graph.txt
156    $ref: /schemas/graph.yaml#/properties/port
157
158  enable-manual-drd:
159    $ref: /schemas/types.yaml#/definitions/flag
160    description:
161      supports manual dual-role switch via debugfs; usually used when
162      receptacle is TYPE-A and also wants to support dual-role mode.
163    type: boolean
164
165  wakeup-source:
166    description: enable USB remote wakeup, see power/wakeup-source.txt
167    type: boolean
168
169  mediatek,syscon-wakeup:
170    $ref: /schemas/types.yaml#/definitions/phandle-array
171    maxItems: 1
172    description:
173      A phandle to syscon used to access the register of the USB wakeup glue
174      layer between xHCI and SPM, the field should always be 3 cells long.
175    items:
176      items:
177        - description:
178            The first cell represents a phandle to syscon
179        - description:
180            The second cell represents the register base address of the glue
181            layer in syscon
182        - description: |
183            The third cell represents the hardware version of the glue layer,
184            1 - used by mt8173 etc, revision 1 without following IPM rule;
185            2 - used by mt2712 etc, revision 2 with following IPM rule;
186            101 - used by mt8183, specific 1.01;
187            102 - used by mt8192, specific 1.02;
188          enum: [1, 2, 101, 102]
189
190  mediatek,u3p-dis-msk:
191    $ref: /schemas/types.yaml#/definitions/uint32
192    description: The mask to disable u3ports, bit0 for u3port0,
193      bit1 for u3port1, ... etc
194
195  mediatek,u2p-dis-msk:
196    $ref: /schemas/types.yaml#/definitions/uint32
197    description: The mask to disable u2ports, bit0 for u2port0,
198      bit1 for u2port1, ... etc; but can't disable u2port0 if dual role mode
199      is enabled, so will be skipped in this case.
200
201# Required child node when support dual-role
202patternProperties:
203  "^usb@[0-9a-f]+$":
204    type: object
205    $ref: /schemas/usb/mediatek,mtk-xhci.yaml#
206    description:
207      The xhci should be added as subnode to mtu3 as shown in the following
208      example if the host mode is enabled.
209
210dependencies:
211  connector: [ usb-role-switch ]
212  port: [ usb-role-switch ]
213  role-switch-default-mode: [ usb-role-switch ]
214  wakeup-source: [ 'mediatek,syscon-wakeup' ]
215
216required:
217  - compatible
218  - reg
219  - reg-names
220  - interrupts
221  - clocks
222  - clock-names
223
224additionalProperties: false
225
226examples:
227  # Dual role switch by extcon
228  - |
229    #include <dt-bindings/clock/mt8173-clk.h>
230    #include <dt-bindings/interrupt-controller/arm-gic.h>
231    #include <dt-bindings/interrupt-controller/irq.h>
232    #include <dt-bindings/phy/phy.h>
233    #include <dt-bindings/power/mt8173-power.h>
234
235    usb@11271000 {
236        compatible = "mediatek,mt8173-mtu3", "mediatek,mtu3";
237        reg = <0x11271000 0x3000>, <0x11280700 0x0100>;
238        reg-names = "mac", "ippc";
239        interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_LOW>;
240        phys = <&phy_port0 PHY_TYPE_USB3>, <&phy_port1 PHY_TYPE_USB2>;
241        power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
242        clocks = <&topckgen CLK_TOP_USB30_SEL>;
243        clock-names = "sys_ck";
244        vusb33-supply = <&mt6397_vusb_reg>;
245        vbus-supply = <&usb_p0_vbus>;
246        extcon = <&extcon_usb>;
247        dr_mode = "otg";
248        wakeup-source;
249        mediatek,syscon-wakeup = <&pericfg 0x400 1>;
250        #address-cells = <1>;
251        #size-cells = <1>;
252        ranges;
253
254        xhci: usb@11270000 {
255            compatible = "mediatek,mt8173-xhci", "mediatek,mtk-xhci";
256            reg = <0x11270000 0x1000>;
257            reg-names = "mac";
258            interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
259            power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
260            clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>;
261            clock-names = "sys_ck", "ref_ck";
262            vusb33-supply = <&mt6397_vusb_reg>;
263        };
264    };
265
266  # Dual role switch by gpio-usb-b-connector
267  - |
268    #include <dt-bindings/gpio/gpio.h>
269    #include <dt-bindings/power/mt2712-power.h>
270
271    usb@112c1000 {
272        compatible = "mediatek,mt2712-mtu3", "mediatek,mtu3";
273        reg = <0x112c1000 0x3000>, <0x112d0700 0x0100>;
274        reg-names = "mac", "ippc";
275        interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_LOW>;
276        phys = <&u2port2 PHY_TYPE_USB2>;
277        power-domains = <&scpsys MT2712_POWER_DOMAIN_USB2>;
278        clocks = <&topckgen CLK_TOP_USB30_SEL>;
279        clock-names = "sys_ck";
280        dr_mode = "otg";
281        usb-role-switch;
282        #address-cells = <1>;
283        #size-cells = <1>;
284        ranges;
285
286        host0: usb@11270000 {
287            compatible = "mediatek,mt2712-xhci", "mediatek,mtk-xhci";
288            reg = <0x11270000 0x1000>;
289            reg-names = "mac";
290            interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_LOW>;
291            power-domains = <&scpsys MT2712_POWER_DOMAIN_USB>;
292            clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>;
293            clock-names = "sys_ck", "ref_ck";
294        };
295
296        connector {
297            compatible = "gpio-usb-b-connector", "usb-b-connector";
298            type = "micro";
299            id-gpios = <&pio 12 GPIO_ACTIVE_HIGH>;
300            vbus-supply = <&usb_p0_vbus>;
301        };
302    };
303
304  # Dual role switch with type-c
305  - |
306    usb@11201000 {
307        compatible = "mediatek,mt8183-mtu3", "mediatek,mtu3";
308        reg = <0x11201000 0x2e00>, <0x11203e00 0x0100>;
309        reg-names = "mac", "ippc";
310        interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_LOW>;
311        phys = <&u2port0 PHY_TYPE_USB2>;
312        clocks = <&clk26m>;
313        clock-names = "sys_ck";
314        mediatek,syscon-wakeup = <&pericfg 0x400 1>;
315        wakeup-source;
316        dr_mode = "otg";
317        usb-role-switch;
318        role-switch-default-mode = "host";
319        #address-cells = <1>;
320        #size-cells = <1>;
321        ranges;
322
323        host: usb@11200000 {
324            compatible = "mediatek,mt8183-xhci", "mediatek,mtk-xhci";
325            reg = <0x11200000 0x1000>;
326            reg-names = "mac";
327            interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_LOW>;
328            clocks = <&clk26m>;
329            clock-names = "sys_ck";
330        };
331
332        port {
333            usb_role_sw: endpoint {
334                remote-endpoint = <&hs_ep>;
335            };
336        };
337    };
338
339...
340