1Davinci SPI controller device bindings
2
3Links on DM:
4Keystone 2 - http://www.ti.com/lit/ug/sprugp2a/sprugp2a.pdf
5dm644x - http://www.ti.com/lit/ug/sprue32a/sprue32a.pdf
6OMAP-L138/da830 - http://www.ti.com/lit/ug/spruh77a/spruh77a.pdf
7
8Required properties:
9- #address-cells: number of cells required to define a chip select
10	address on the SPI bus. Should be set to 1.
11- #size-cells: should be zero.
12- compatible:
13	- "ti,dm6441-spi" for SPI used similar to that on DM644x SoC family
14	- "ti,da830-spi" for SPI used similar to that on DA8xx SoC family
15	- "ti,keystone-spi" for SPI used similar to that on Keystone2 SoC
16		family
17- reg: Offset and length of SPI controller register space
18- num-cs: Number of chip selects. This includes internal as well as
19	GPIO chip selects.
20- ti,davinci-spi-intr-line: interrupt line used to connect the SPI
21	IP to the interrupt controller within the SoC. Possible values
22	are 0 and 1. Manual says one of the two possible interrupt
23	lines can be tied to the interrupt controller. Set this
24	based on a specific SoC configuration.
25- interrupts: interrupt number mapped to CPU.
26- clocks: spi clk phandle
27
28Optional:
29- cs-gpios: gpio chip selects
30	For example to have 3 internal CS and 2 GPIO CS, user could define
31	cs-gpios = <0>, <0>, <0>, <&gpio1 30 0>, <&gpio1 31 0>;
32	where first three are internal CS and last two are GPIO CS.
33
34Optional properties for slave devices:
35SPI slave nodes can contain the following properties.
36Not all SPI Peripherals from Texas Instruments support this.
37Please check SPI peripheral documentation for a device before using these.
38
39- ti,spi-wdelay : delay between transmission of words
40	(SPIFMTn.WDELAY, SPIDAT1.WDEL) must be specified in number of SPI module
41	clock periods.
42
43	delay = WDELAY * SPI_module_clock_period + 2 * SPI_module_clock_period
44
45Below is timing diagram which shows functional meaning of
46"ti,spi-wdelay" parameter.
47
48             +-+ +-+ +-+ +-+ +-+                           +-+ +-+ +-+
49SPI_CLK      | | | | | | | | | |                           | | | | | |
50  +----------+ +-+ +-+ +-+ +-+ +---------------------------+ +-+ +-+ +-
51
52SPI_SOMI/SIMO+-----------------+                           +-----------
53  +----------+ word1           +---------------------------+word2
54             +-----------------+                           +-----------
55                                          WDELAY
56                                <-------------------------->
57
58Example of a NOR flash slave device (n25q032) connected to DaVinci
59SPI controller device over the SPI bus.
60
61spi0:spi@20BF0000 {
62	#address-cells			= <1>;
63	#size-cells			= <0>;
64	compatible			= "ti,dm6446-spi";
65	reg				= <0x20BF0000 0x1000>;
66	num-cs				= <4>;
67	ti,davinci-spi-intr-line	= <0>;
68	interrupts			= <338>;
69	clocks				= <&clkspi>;
70
71	flash: n25q032@0 {
72		#address-cells = <1>;
73		#size-cells = <1>;
74		compatible = "st,m25p32";
75		spi-max-frequency = <25000000>;
76		reg = <0>;
77		ti,spi-wdelay = <8>;
78
79		partition@0 {
80			label = "u-boot-spl";
81			reg = <0x0 0x80000>;
82			read-only;
83		};
84
85		partition@1 {
86			label = "test";
87			reg = <0x80000 0x380000>;
88		};
89	};
90};
91