1STA350 audio CODEC
2
3The driver for this device only supports I2C.
4
5Required properties:
6
7  - compatible: "st,sta350"
8  - reg: the I2C address of the device for I2C
9  - reset-gpios: a GPIO spec for the reset pin. If specified, it will be
10		 deasserted before communication to the codec starts.
11
12  - power-down-gpios: a GPIO spec for the power down pin. If specified,
13		      it will be deasserted before communication to the codec
14		      starts.
15
16  - vdd-dig-supply: regulator spec, providing 3.3V
17  - vdd-pll-supply: regulator spec, providing 3.3V
18  - vcc-supply: regulator spec, providing 5V - 26V
19
20Optional properties:
21
22  -  st,output-conf: number, Selects the output configuration:
23	0: 2-channel (full-bridge) power, 2-channel data-out
24	1: 2 (half-bridge). 1 (full-bridge) on-board power
25	2: 2 Channel (Full-Bridge) Power, 1 Channel FFX
26	3: 1 Channel Mono-Parallel
27	If parameter is missing, mode 0 will be enabled.
28	This property has to be specified as '/bits/ 8' value.
29
30  -  st,ch1-output-mapping: Channel 1 output mapping
31  -  st,ch2-output-mapping: Channel 2 output mapping
32  -  st,ch3-output-mapping: Channel 3 output mapping
33	0: Channel 1
34	1: Channel 2
35	2: Channel 3
36	If parameter is missing, channel 1 is chosen.
37	This properties have to be specified as '/bits/ 8' values.
38
39  -  st,thermal-warning-recover:
40	If present, thermal warning recovery is enabled.
41
42  -  st,thermal-warning-adjustment:
43	If present, thermal warning adjustment is enabled.
44
45  -  st,fault-detect-recovery:
46	If present, then fault recovery will be enabled.
47
48  -  st,ffx-power-output-mode: string
49	The FFX power output mode selects how the FFX output timing is
50	configured. Must be one of these values:
51	  -  "drop-compensation"
52	  -  "tapered-compensation"
53	  -  "full-power-mode"
54	  -  "variable-drop-compensation" (default)
55
56  -  st,drop-compensation-ns: number
57	Only required for "st,ffx-power-output-mode" ==
58	"variable-drop-compensation".
59	Specifies the drop compensation in nanoseconds.
60	The value must be in the range of 0..300, and only
61	multiples of 20 are allowed. Default is 140ns.
62
63  -  st,overcurrent-warning-adjustment:
64	If present, overcurrent warning adjustment is enabled.
65
66  -  st,max-power-use-mpcc:
67	If present, then MPCC bits are used for MPC coefficients,
68	otherwise standard MPC coefficients are used.
69
70  -  st,max-power-corr:
71	If present, power bridge correction for THD reduction near maximum
72	power output is enabled.
73
74  -  st,am-reduction-mode:
75	If present, FFX mode runs in AM reduction mode, otherwise normal
76	FFX mode is used.
77
78  -  st,odd-pwm-speed-mode:
79	If present, PWM speed mode run on odd speed mode (341.3 kHz) on all
80	channels. If not present, normal PWM spped mode (384 kHz) will be used.
81
82  -  st,distortion-compensation:
83	If present, distortion compensation variable uses DCC coefficient.
84	If not present, preset DC coefficient is used.
85
86  -  st,invalid-input-detect-mute:
87	If present, automatic invalid input detect mute is enabled.
88
89  -  st,activate-mute-output:
90	If present, a mute output will be activated in ase the volume will
91	reach a value lower than -76 dBFS.
92
93  -  st,bridge-immediate-off:
94	If present, the bridge will be switched off immediately after the
95	power-down-gpio goes low. Otherwise, the bridge will wait for 13
96	million clock cycles to pass before shutting down.
97
98  -  st,noise-shape-dc-cut:
99	If present, the noise-shaping technique on the DC cutoff filter are
100	enabled.
101
102  -  st,powerdown-master-volume:
103	If present, the power-down pin and I2C power-down functions will
104	act on the master volume. Otherwise, the functions will act on the
105	mute commands.
106
107  -  st,powerdown-delay-divider:
108	If present, the bridge power-down time will be divided by the provided
109	value. If not specified, a divider of 1 will be used. Allowed values
110	are 1, 2, 4, 8, 16, 32, 64 and 128.
111	This property has to be specified as '/bits/ 8' value.
112
113Example:
114
115codec: sta350@38 {
116	compatible = "st,sta350";
117	reg = <0x1c>;
118	reset-gpios = <&gpio1 19 0>;
119	power-down-gpios = <&gpio1 16 0>;
120	st,output-conf = /bits/ 8  <0x3>;	// set output to 2-channel
121						// (full-bridge) power,
122						// 2-channel data-out
123	st,ch1-output-mapping = /bits/ 8 <0>;	// set channel 1 output ch 1
124	st,ch2-output-mapping = /bits/ 8 <0>;	// set channel 2 output ch 1
125	st,ch3-output-mapping = /bits/ 8 <0>;	// set channel 3 output ch 1
126	st,max-power-correction;		// enables power bridge
127						// correction for THD reduction
128						// near maximum power output
129	st,invalid-input-detect-mute;		// mute if no valid digital
130						// audio signal is provided.
131};
132