1* UCC (Unified Communications Controllers)
2
3Required properties:
4- device_type : should be "network", "hldc", "uart", "transparent"
5  "bisync", "atm", or "serial".
6- compatible : could be "ucc_geth" or "fsl_atm" and so on.
7- cell-index : the ucc number(1-8), corresponding to UCCx in UM.
8- reg : Offset and length of the register set for the device
9- interrupts : <a b> where a is the interrupt number and b is a
10  field that represents an encoding of the sense and level
11  information for the interrupt.  This should be encoded based on
12  the information in section 2) depending on the type of interrupt
13  controller you have.
14- interrupt-parent : the phandle for the interrupt controller that
15  services interrupts for this device.
16- pio-handle : The phandle for the Parallel I/O port configuration.
17- port-number : for UART drivers, the port number to use, between 0 and 3.
18  This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0.
19  The port number is added to the minor number of the device.  Unlike the
20  CPM UART driver, the port-number is required for the QE UART driver.
21- soft-uart : for UART drivers, if specified this means the QE UART device
22  driver should use "Soft-UART" mode, which is needed on some SOCs that have
23  broken UART hardware.  Soft-UART is provided via a microcode upload.
24- rx-clock-name: the UCC receive clock source
25  "none": clock source is disabled
26  "brg1" through "brg16": clock source is BRG1-BRG16, respectively
27  "clk1" through "clk24": clock source is CLK1-CLK24, respectively
28- tx-clock-name: the UCC transmit clock source
29  "none": clock source is disabled
30  "brg1" through "brg16": clock source is BRG1-BRG16, respectively
31  "clk1" through "clk24": clock source is CLK1-CLK24, respectively
32The following two properties are deprecated.  rx-clock has been replaced
33with rx-clock-name, and tx-clock has been replaced with tx-clock-name.
34Drivers that currently use the deprecated properties should continue to
35do so, in order to support older device trees, but they should be updated
36to check for the new properties first.
37- rx-clock : represents the UCC receive clock source.
38  0x00 : clock source is disabled;
39  0x1~0x10 : clock source is BRG1~BRG16 respectively;
40  0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
41- tx-clock: represents the UCC transmit clock source;
42  0x00 : clock source is disabled;
43  0x1~0x10 : clock source is BRG1~BRG16 respectively;
44  0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
45
46Required properties for network device_type:
47- mac-address : list of bytes representing the ethernet address.
48- phy-handle : The phandle for the PHY connected to this controller.
49
50Recommended properties:
51- phy-connection-type : a string naming the controller/PHY interface type,
52  i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal
53  Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only),
54  "tbi", or "rtbi".
55
56Example:
57	ucc@2000 {
58		device_type = "network";
59		compatible = "ucc_geth";
60		cell-index = <1>;
61		reg = <2000 200>;
62		interrupts = <a0 0>;
63		interrupt-parent = <700>;
64		mac-address = [ 00 04 9f 00 23 23 ];
65		rx-clock = "none";
66		tx-clock = "clk9";
67		phy-handle = <212000>;
68		phy-connection-type = "gmii";
69		pio-handle = <140001>;
70	};
71