1# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
2%YAML 1.2
3---
4$id: http://devicetree.org/schemas/regulator/rohm,bd71815-regulator.yaml#
5$schema: http://devicetree.org/meta-schemas/core.yaml#
6
7title: ROHM BD71815 Power Management Integrated Circuit regulators
8
9maintainers:
10  - Matti Vaittinen <mazziesaccount@gmail.com>
11
12description: |
13  This module is part of the ROHM BD718215 MFD device. For more details
14  see Documentation/devicetree/bindings/mfd/rohm,bd71815-pmic.yaml.
15
16  The regulator controller is represented as a sub-node of the PMIC node
17  on the device tree.
18
19  The valid names for BD71815 regulator nodes are
20  buck1, buck2, buck3, buck4, buck5,
21  ldo1, ldo2, ldo3, ldo4, ldo5,
22  ldodvref, ldolpsr, wled
23
24properties:
25  wled:
26    type: object
27    description:
28      properties for wled regulator
29    $ref: regulator.yaml#
30    unevaluatedProperties: false
31
32    properties:
33      regulator-name:
34        const: wled
35
36patternProperties:
37  "^((ldo|buck)[1-5]|ldolpsr|ldodvref)$":
38    type: object
39    description:
40      Properties for single LDO/BUCK regulator.
41    $ref: regulator.yaml#
42
43    properties:
44      regulator-name:
45        pattern: "^((ldo|buck)[1-5]|ldolpsr|ldodvref)$"
46        description:
47          should be "ldo1", ..., "ldo5", "buck1", ..., "buck5" and "ldolpsr"
48          for ldolpsr regulator, "ldodvref" for ldodvref reglator.
49
50      rohm,vsel-gpios:
51        description:
52          GPIO used to control ldo4 state (when ldo4 is controlled by GPIO).
53
54      rohm,dvs-run-voltage:
55        description:
56          PMIC "RUN" state voltage in uV when PMIC HW states are used. See
57          comments below for bucks/LDOs which support this. 0 means
58          regulator should be disabled at RUN state.
59        $ref: "/schemas/types.yaml#/definitions/uint32"
60        minimum: 0
61        maximum: 3300000
62
63      rohm,dvs-snvs-voltage:
64        description:
65          Whether to keep regulator enabled at "SNVS" state or not.
66          0 means regulator should be disabled at SNVS state, non zero voltage
67          keeps regulator enabled. BD71815 does not change voltage level
68          when PMIC transitions to SNVS.SNVS voltage depends on the previous
69          state (from which the PMIC transitioned to SNVS).
70        $ref: "/schemas/types.yaml#/definitions/uint32"
71        minimum: 0
72        maximum: 3300000
73
74      rohm,dvs-suspend-voltage:
75        description:
76          PMIC "SUSPEND" state voltage in uV when PMIC HW states are used. See
77          comments below for bucks/LDOs which support this. 0 means
78          regulator should be disabled at SUSPEND state.
79        $ref: "/schemas/types.yaml#/definitions/uint32"
80        minimum: 0
81        maximum: 3300000
82
83      rohm,dvs-lpsr-voltage:
84        description:
85          PMIC "LPSR" state voltage in uV when PMIC HW states are used. See
86          comments below for bucks/LDOs which support this. 0 means
87          regulator should be disabled at LPSR state.
88        $ref: "/schemas/types.yaml#/definitions/uint32"
89        minimum: 0
90        maximum: 3300000
91
92        # Bucks 1 and 2 support giving separate voltages for operational states
93        # (RUN /CLEAN according to data-sheet) and non operational states
94        # (LPSR/SUSPEND). The voltage is automatically changed when HW
95        # state changes. Omitting these properties from bucks 1 and 2 leave
96        # buck voltages to not be toggled by HW state. Enable status may still
97        # be toggled by state changes depending on HW default settings.
98        #
99        # Bucks 3-5 and ldos 1-5 support setting the RUN state voltage here.
100        # Given RUN voltage is used at all states if regulator is enabled at
101        # given state.
102        # Values given for other states are regarded as enable/disable at
103        # given state (see below).
104        #
105        # All regulators except WLED support specifying enable/disable status
106        # for each of the HW states (RUN/SNVS/SUSPEND/LPSR). HW defaults can
107        # be overridden by setting voltage to 0 (regulator disabled at given
108        # state) or non-zero (regulator enabled at given state). Please note
109        # that setting non zero voltages for bucks 1/2 will also enable voltage
110        # changes according to state change.
111
112    required:
113      - regulator-name
114
115    unevaluatedProperties: false
116
117additionalProperties: false
118