1Voltage/Current Regulators
2
3Optional properties:
4- regulator-name: A string used as a descriptive name for regulator outputs
5- regulator-min-microvolt: smallest voltage consumers may set
6- regulator-max-microvolt: largest voltage consumers may set
7- regulator-microvolt-offset: Offset applied to voltages to compensate for voltage drops
8- regulator-min-microamp: smallest current consumers may set
9- regulator-max-microamp: largest current consumers may set
10- regulator-input-current-limit-microamp: maximum input current regulator allows
11- regulator-always-on: boolean, regulator should never be disabled
12- regulator-boot-on: bootloader/firmware enabled regulator
13- regulator-allow-bypass: allow the regulator to go into bypass mode
14- regulator-allow-set-load: allow the regulator performance level to be configured
15- <name>-supply: phandle to the parent supply/regulator node
16- regulator-ramp-delay: ramp delay for regulator(in uV/us)
17  For hardware which supports disabling ramp rate, it should be explicitly
18  initialised to zero (regulator-ramp-delay = <0>) for disabling ramp delay.
19- regulator-enable-ramp-delay: The time taken, in microseconds, for the supply
20  rail to reach the target voltage, plus/minus whatever tolerance the board
21  design requires. This property describes the total system ramp time
22  required due to the combination of internal ramping of the regulator itself,
23  and board design issues such as trace capacitance and load on the supply.
24- regulator-settling-time-us: Settling time, in microseconds, for voltage
25  change if regulator have the constant time for any level voltage change.
26  This is useful when regulator have exponential voltage change.
27- regulator-settling-time-up-us: Settling time, in microseconds, for voltage
28  increase if the regulator needs a constant time to settle after voltage
29  increases of any level. This is useful for regulators with exponential
30  voltage changes.
31- regulator-settling-time-down-us: Settling time, in microseconds, for voltage
32  decrease if the regulator needs a constant time to settle after voltage
33  decreases of any level. This is useful for regulators with exponential
34  voltage changes.
35- regulator-soft-start: Enable soft start so that voltage ramps slowly
36- regulator-state-mem sub-root node for Suspend-to-RAM mode
37  : suspend to memory, the device goes to sleep, but all data stored in memory,
38  only some external interrupt can wake the device.
39- regulator-state-disk sub-root node for Suspend-to-DISK mode
40  : suspend to disk, this state operates similarly to Suspend-to-RAM,
41  but includes a final step of writing memory contents to disk.
42- regulator-state-[mem/disk] node has following common properties:
43	- regulator-on-in-suspend: regulator should be on in suspend state.
44	- regulator-off-in-suspend: regulator should be off in suspend state.
45	- regulator-suspend-min-microvolt: minimum voltage may be set in
46	  suspend state.
47	- regulator-suspend-max-microvolt: maximum voltage may be set in
48	  suspend state.
49	- regulator-suspend-microvolt: the default voltage which regulator
50	  would be set in suspend. This property is now deprecated, instead
51	  setting voltage for suspend mode via the API which regulator
52	  driver provides is recommended.
53	- regulator-changeable-in-suspend: whether the default voltage and
54	  the regulator on/off in suspend can be changed in runtime.
55	- regulator-mode: operating mode in the given suspend state.
56	  The set of possible operating modes depends on the capabilities of
57	  every hardware so the valid modes are documented on each regulator
58	  device tree binding document.
59- regulator-initial-mode: initial operating mode. The set of possible operating
60  modes depends on the capabilities of every hardware so each device binding
61  documentation explains which values the regulator supports.
62- regulator-allowed-modes: list of operating modes that software is allowed to
63  configure for the regulator at run-time.  Elements may be specified in any
64  order.  The set of possible operating modes depends on the capabilities of
65  every hardware so each device binding document explains which values the
66  regulator supports.
67- regulator-system-load: Load in uA present on regulator that is not captured by
68  any consumer request.
69- regulator-pull-down: Enable pull down resistor when the regulator is disabled.
70- regulator-over-current-protection: Enable over current protection.
71- regulator-active-discharge: tristate, enable/disable active discharge of
72  regulators. The values are:
73	0: Disable active discharge.
74	1: Enable active discharge.
75	Absence of this property will leave configuration to default.
76- regulator-coupled-with: Regulators with which the regulator
77  is coupled. The linkage is 2-way - all coupled regulators should be linked
78  with each other. A regulator should not be coupled with its supplier.
79- regulator-coupled-max-spread: Max spread between voltages of coupled regulators
80  in microvolts.
81
82Deprecated properties:
83- regulator-compatible: If a regulator chip contains multiple
84  regulators, and if the chip's binding contains a child node that
85  describes each regulator, then this property indicates which regulator
86  this child node is intended to configure. If this property is missing,
87  the node's name will be used instead.
88
89Example:
90
91	xyzreg: regulator@0 {
92		regulator-min-microvolt = <1000000>;
93		regulator-max-microvolt = <2500000>;
94		regulator-always-on;
95		vin-supply = <&vin>;
96
97		regulator-state-mem {
98			regulator-on-in-suspend;
99		};
100	};
101
102Regulator Consumers:
103Consumer nodes can reference one or more of its supplies/
104regulators using the below bindings.
105
106- <name>-supply: phandle to the regulator node
107
108These are the same bindings that a regulator in the above
109example used to reference its own supply, in which case
110its just seen as a special case of a regulator being a
111consumer itself.
112
113Example of a consumer device node (mmc) referencing two
114regulators (twl_reg1 and twl_reg2),
115
116	twl_reg1: regulator@0 {
117		...
118		...
119		...
120	};
121
122	twl_reg2: regulator@1 {
123		...
124		...
125		...
126	};
127
128	mmc: mmc@0 {
129		...
130		...
131		vmmc-supply = <&twl_reg1>;
132		vmmcaux-supply = <&twl_reg2>;
133	};
134