1# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
2# Copyright (C) STMicroelectronics 2019.
3%YAML 1.2
4---
5$id: http://devicetree.org/schemas/pinctrl/st,stm32-pinctrl.yaml#
6$schema: http://devicetree.org/meta-schemas/core.yaml#
7
8title: STM32 GPIO and Pin Mux/Config controller
9
10maintainers:
11  - Alexandre TORGUE <alexandre.torgue@st.com>
12
13description: |
14  STMicroelectronics's STM32 MCUs intregrate a GPIO and Pin mux/config hardware
15  controller. It controls the input/output settings on the available pins and
16  also provides ability to multiplex and configure the output of various
17  on-chip controllers onto these pads.
18
19properties:
20  compatible:
21    enum:
22      - st,stm32f429-pinctrl
23      - st,stm32f469-pinctrl
24      - st,stm32f746-pinctrl
25      - st,stm32f769-pinctrl
26      - st,stm32h743-pinctrl
27      - st,stm32mp157-pinctrl
28      - st,stm32mp157-z-pinctrl
29
30  '#address-cells':
31    const: 1
32  '#size-cells':
33    const: 1
34
35  ranges: true
36  pins-are-numbered: true
37  hwlocks: true
38
39  st,syscfg:
40    $ref: "/schemas/types.yaml#/definitions/phandle-array"
41    description: Should be phandle/offset/mask
42    items:
43      - description: Phandle to the syscon node which includes IRQ mux selection.
44      - description: The offset of the IRQ mux selection register.
45      - description: The field mask of IRQ mux, needed if different of 0xf.
46
47  st,package:
48    allOf:
49      - $ref: /schemas/types.yaml#/definitions/uint32
50      - enum: [1, 2, 4, 8]
51    description:
52     Indicates the SOC package used.
53     More details in include/dt-bindings/pinctrl/stm32-pinfunc.h
54
55
56patternProperties:
57  '^gpio@[0-9a-f]*$':
58    type: object
59    properties:
60      gpio-controller: true
61      '#gpio-cells':
62        const: 2
63
64      reg:
65        maxItems: 1
66      clocks:
67        maxItems: 1
68      reset:
69        minItems: 1
70        maxItems: 1
71      gpio-ranges:
72        minItems: 1
73        maxItems: 16
74      ngpios:
75        description:
76          Number of available gpios in a bank.
77        minimum: 1
78        maximum: 16
79
80      st,bank-name:
81        allOf:
82          - $ref: "/schemas/types.yaml#/definitions/string"
83          - enum:
84            - GPIOA
85            - GPIOB
86            - GPIOC
87            - GPIOD
88            - GPIOE
89            - GPIOF
90            - GPIOG
91            - GPIOH
92            - GPIOI
93            - GPIOJ
94            - GPIOK
95            - GPIOZ
96        description:
97          Should be a name string for this bank as specified in the datasheet.
98
99      st,bank-ioport:
100        allOf:
101          - $ref: "/schemas/types.yaml#/definitions/uint32"
102          - minimum: 0
103          - maximum: 11
104
105        description:
106          Should correspond to the EXTI IOport selection (EXTI line used
107          to select GPIOs as interrupts).
108
109    required:
110      - gpio-controller
111      - '#gpio-cells'
112      - reg
113      - clocks
114      - st,bank-name
115
116  '-[0-9]*$':
117    type: object
118    patternProperties:
119      '^pins':
120        type: object
121        description: |
122          A pinctrl node should contain at least one subnode representing the
123          pinctrl group available on the machine. Each subnode will list the
124          pins it needs, and how they should be configured, with regard to muxer
125          configuration, pullups, drive, output high/low and output speed.
126        properties:
127          pinmux:
128            allOf:
129              - $ref: "/schemas/types.yaml#/definitions/uint32-array"
130            description: |
131              Integer array, represents gpio pin number and mux setting.
132              Supported pin number and mux varies for different SoCs, and are
133              defined in dt-bindings/pinctrl/<soc>-pinfunc.h directly.
134              These defines are calculated as: ((port * 16 + line) << 8) | function
135              With:
136              - port: The gpio port index (PA = 0, PB = 1, ..., PK = 11)
137              - line: The line offset within the port (PA0 = 0, PA1 = 1, ..., PA15 = 15)
138              - function: The function number, can be:
139              * 0 : GPIO
140              * 1 : Alternate Function 0
141              * 2 : Alternate Function 1
142              * 3 : Alternate Function 2
143              * ...
144              * 16 : Alternate Function 15
145              * 17 : Analog
146              To simplify the usage, macro is available to generate "pinmux" field.
147              This macro is available here:
148                - include/dt-bindings/pinctrl/stm32-pinfunc.h
149              Some examples of using macro:
150               /* GPIO A9 set as alernate function 2 */
151               ... {
152                          pinmux = <STM32_PINMUX('A', 9, AF2)>;
153               };
154               /* GPIO A9 set as GPIO  */
155               ... {
156                          pinmux = <STM32_PINMUX('A', 9, GPIO)>;
157               };
158               /* GPIO A9 set as analog */
159               ... {
160                          pinmux = <STM32_PINMUX('A', 9, ANALOG)>;
161               };
162
163          bias-disable:
164            type: boolean
165          bias-pull-down:
166            type: boolean
167          bias-pull-up:
168            type: boolean
169          drive-push-pull:
170            type: boolean
171          drive-open-drain:
172            type: boolean
173          output-low:
174            type: boolean
175          output-high:
176            type: boolean
177          slew-rate:
178            description: |
179              0: Low speed
180              1: Medium speed
181              2: Fast speed
182              3: High speed
183            allOf:
184              - $ref: /schemas/types.yaml#/definitions/uint32
185              - enum: [0, 1, 2, 3]
186
187        required:
188          - pinmux
189
190required:
191  - compatible
192  - '#address-cells'
193  - '#size-cells'
194  - ranges
195  - pins-are-numbered
196
197examples:
198  - |
199    #include <dt-bindings/pinctrl/stm32-pinfunc.h>
200    #include <dt-bindings/mfd/stm32f4-rcc.h>
201    //Example 1
202      pinctrl@40020000 {
203              #address-cells = <1>;
204              #size-cells = <1>;
205              compatible = "st,stm32f429-pinctrl";
206              ranges = <0 0x40020000 0x3000>;
207              pins-are-numbered;
208
209              gpioa: gpio@0 {
210                      gpio-controller;
211                      #gpio-cells = <2>;
212                      reg = <0x0 0x400>;
213                      resets = <&reset_ahb1 0>;
214                      clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOA)>;
215                      st,bank-name = "GPIOA";
216              };
217       };
218
219    //Example 2 (using gpio-ranges)
220      pinctrl@50020000 {
221              #address-cells = <1>;
222              #size-cells = <1>;
223              compatible = "st,stm32f429-pinctrl";
224              ranges = <0 0x50020000 0x3000>;
225              pins-are-numbered;
226
227              gpiob: gpio@1000 {
228                      gpio-controller;
229                      #gpio-cells = <2>;
230                      reg = <0x1000 0x400>;
231                      resets = <&reset_ahb1 0>;
232                      clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOB)>;
233                      st,bank-name = "GPIOB";
234                      gpio-ranges = <&pinctrl 0 0 16>;
235              };
236
237              gpioc: gpio@2000 {
238                      gpio-controller;
239                      #gpio-cells = <2>;
240                      reg = <0x2000 0x400>;
241                      resets = <&reset_ahb1 0>;
242                      clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOC)>;
243                      st,bank-name = "GPIOC";
244                      ngpios = <5>;
245                      gpio-ranges = <&pinctrl 0 16 3>,
246                                    <&pinctrl 14 30 2>;
247              };
248      };
249
250    //Example 3 pin groups
251      pinctrl@60020000 {
252        usart1_pins_a: usart1-0 {
253                pins1 {
254                        pinmux = <STM32_PINMUX('A', 9, AF7)>;
255                        bias-disable;
256                        drive-push-pull;
257                        slew-rate = <0>;
258                };
259                pins2 {
260                        pinmux = <STM32_PINMUX('A', 10, AF7)>;
261                        bias-disable;
262                };
263        };
264    };
265
266    usart1 {
267                pinctrl-0 = <&usart1_pins_a>;
268                pinctrl-names = "default";
269    };
270
271...
272