1Palmas Pincontrol bindings
2
3The pins of Palmas device can be set on different option and provides
4the configuration for Pull UP/DOWN, open drain etc.
5
6Required properties:
7- compatible: It must be one of following:
8  - "ti,palmas-pinctrl" for Palma series of the pincontrol.
9  - "ti,tps65913-pinctrl" for Palma series device TPS65913.
10  - "ti,tps80036-pinctrl" for Palma series device TPS80036.
11
12Please refer to pinctrl-bindings.txt in this directory for details of the
13common pinctrl bindings used by client devices, including the meaning of the
14phrase "pin configuration node".
15
16Palmas's pin configuration nodes act as a container for an arbitrary number of
17subnodes. Each of these subnodes represents some desired configuration for a
18list of pins. This configuration can include the mux function to select on
19those pin(s), and various pin configuration parameters, such as pull-up,
20open drain.
21
22The name of each subnode is not important; all subnodes should be enumerated
23and processed purely based on their content.
24
25Each subnode only affects those parameters that are explicitly listed. In
26other words, a subnode that lists a mux function but no pin configuration
27parameters implies no information about any pin configuration parameters.
28Similarly, a pin subnode that describes a pullup parameter implies no
29information about e.g. the mux function.
30
31Optional properties:
32- ti,palmas-enable-dvfs1: Enable DVFS1. Configure pins for DVFS1 mode.
33	Selection primary or secondary function associated to I2C2_SCL_SCE,
34	I2C2_SDA_SDO pin/pad for DVFS1 interface
35- ti,palmas-enable-dvfs2: Enable DVFS2. Configure pins for DVFS2 mode.
36	Selection primary or secondary function associated to GPADC_START
37	and SYSEN2 pin/pad for DVFS2 interface
38
39This binding uses the following generic properties as defined in
40pinctrl-bindings.txt:
41
42Required: pins
43Options: function, bias-disable, bias-pull-up, bias-pull-down,
44	 bias-pin-default, drive-open-drain.
45
46Note that many of these properties are only valid for certain specific pins.
47See the Palmas device datasheet for complete details regarding which pins
48support which functionality.
49
50Valid values for pin names are:
51	gpio0, gpio1, gpio2, gpio3, gpio4, gpio5, gpio6, gpio7, gpio8, gpio9,
52	gpio10, gpio11, gpio12, gpio13, gpio14, gpio15, vac, powergood,
53	nreswarm, pwrdown, gpadc_start, reset_in, nsleep, enable1, enable2,
54	int.
55
56Valid value of function names are:
57	gpio, led, pwm, regen, sysen, clk32kgaudio, id, vbus_det, chrg_det,
58	vac, vacok, powergood, usb_psel, msecure, pwrhold, int, nreswarm,
59	simrsto, simrsti, low_vbat, wireless_chrg1, rcm, pwrdown, gpadc_start,
60	reset_in, nsleep, enable.
61
62There are 4 special functions: opt0, opt1, opt2 and opt3. If any of these
63functions is selected then directly pins register will be written with 0, 1, 2
64or 3 respectively if it is valid for that pins or list of pins.
65
66Example:
67	palmas: tps65913 {
68		....
69		pinctrl {
70			compatible = "ti,tps65913-pinctrl";
71			ti,palmas-enable-dvfs1;
72			pinctrl-names = "default";
73			pinctrl-0 = <&palmas_pins_state>;
74
75			palmas_pins_state: pinmux {
76				gpio0 {
77					pins = "gpio0";
78					function = "id";
79					bias-pull-up;
80				};
81
82				vac {
83					pins = "vac";
84					function = "vacok";
85					bias-pull-down;
86				};
87
88				gpio5 {
89					pins = "gpio5";
90					function = "opt0";
91					drive-open-drain = <1>;
92				};
93			};
94		};
95		....
96	};
97