1TI PHY: DT DOCUMENTATION FOR PHYs in TI PLATFORMs
2
3OMAP CONTROL PHY
4
5Required properties:
6 - compatible: Should be one of
7 "ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4.
8 "ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register
9                        e.g. USB2_PHY on OMAP5.
10 "ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control
11                        e.g. USB3 PHY and SATA PHY on OMAP5.
12 "ti,control-phy-pcie" - for pcie to support external clock for pcie and to
13			set PCS delay value.
14			e.g. PCIE PHY in DRA7x
15 "ti,control-phy-usb2-dra7" - if it has power down register like USB2 PHY on
16                        DRA7 platform.
17 "ti,control-phy-usb2-am437" - if it has power down register like USB2 PHY on
18                        AM437 platform.
19 - reg : register ranges as listed in the reg-names property
20 - reg-names: "otghs_control" for control-phy-otghs
21	      "power", "pcie_pcs" and "control_sma" for control-phy-pcie
22	      "power" for all other types
23
24omap_control_usb: omap-control-usb@4a002300 {
25        compatible = "ti,control-phy-otghs";
26        reg = <0x4a00233c 0x4>;
27        reg-names = "otghs_control";
28};
29
30OMAP USB2 PHY
31
32Required properties:
33 - compatible: Should be "ti,omap-usb2"
34	       Should be "ti,dra7x-usb2" for the 1st instance of USB2 PHY on
35	       DRA7x
36	       Should be "ti,dra7x-usb2-phy2" for the 2nd instance of USB2 PHY
37	       in DRA7x
38 - reg : Address and length of the register set for the device.
39 - #phy-cells: determine the number of cells that should be given in the
40   phandle while referencing this phy.
41 - clocks: a list of phandles and clock-specifier pairs, one for each entry in
42   clock-names.
43 - clock-names: should include:
44   * "wkupclk" - wakeup clock.
45   * "refclk" - reference clock (optional).
46
47Deprecated properties:
48 - ctrl-module : phandle of the control module used by PHY driver to power on
49   the PHY.
50
51Recommended properies:
52- syscon-phy-power : phandle/offset pair. Phandle to the system control
53  module and the register offset to power on/off the PHY.
54
55This is usually a subnode of ocp2scp to which it is connected.
56
57usb2phy@4a0ad080 {
58	compatible = "ti,omap-usb2";
59	reg = <0x4a0ad080 0x58>;
60	ctrl-module = <&omap_control_usb>;
61	#phy-cells = <0>;
62	clocks = <&usb_phy_cm_clk32k>, <&usb_otg_ss_refclk960m>;
63	clock-names = "wkupclk", "refclk";
64};
65
66TI PIPE3 PHY
67
68Required properties:
69 - compatible: Should be "ti,phy-usb3", "ti,phy-pipe3-sata" or
70   "ti,phy-pipe3-pcie. "ti,omap-usb3" is deprecated.
71 - reg : Address and length of the register set for the device.
72 - reg-names: The names of the register addresses corresponding to the registers
73   filled in "reg".
74 - #phy-cells: determine the number of cells that should be given in the
75   phandle while referencing this phy.
76 - clocks: a list of phandles and clock-specifier pairs, one for each entry in
77   clock-names.
78 - clock-names: should include:
79   * "wkupclk" - wakeup clock.
80   * "sysclk" - system clock.
81   * "refclk" - reference clock.
82   * "dpll_ref" - external dpll ref clk
83   * "dpll_ref_m2" - external dpll ref clk
84   * "phy-div" - divider for apll
85   * "div-clk" - apll clock
86
87Optional properties:
88 - id: If there are multiple instance of the same type, in order to
89   differentiate between each instance "id" can be used (e.g., multi-lane PCIe
90   PHY). If "id" is not provided, it is set to default value of '1'.
91 - syscon-pllreset: Handle to system control region that contains the
92   CTRL_CORE_SMA_SW_0 register and register offset to the CTRL_CORE_SMA_SW_0
93   register that contains the SATA_PLL_SOFT_RESET bit. Only valid for sata_phy.
94 - syscon-pcs : phandle/offset pair. Phandle to the system control module and the
95   register offset to write the PCS delay value.
96
97Deprecated properties:
98 - ctrl-module : phandle of the control module used by PHY driver to power on
99   the PHY.
100
101Recommended properies:
102 - syscon-phy-power : phandle/offset pair. Phandle to the system control
103   module and the register offset to power on/off the PHY.
104
105This is usually a subnode of ocp2scp to which it is connected.
106
107usb3phy@4a084400 {
108	compatible = "ti,phy-usb3";
109	reg = <0x4a084400 0x80>,
110	      <0x4a084800 0x64>,
111	      <0x4a084c00 0x40>;
112	reg-names = "phy_rx", "phy_tx", "pll_ctrl";
113	ctrl-module = <&omap_control_usb>;
114	#phy-cells = <0>;
115	clocks = <&usb_phy_cm_clk32k>,
116		 <&sys_clkin>,
117		 <&usb_otg_ss_refclk960m>;
118	clock-names =	"wkupclk",
119			"sysclk",
120			"refclk";
121};
122
123sata_phy: phy@4A096000 {
124	compatible = "ti,phy-pipe3-sata";
125	reg = <0x4A096000 0x80>, /* phy_rx */
126	      <0x4A096400 0x64>, /* phy_tx */
127	      <0x4A096800 0x40>; /* pll_ctrl */
128	reg-names = "phy_rx", "phy_tx", "pll_ctrl";
129	ctrl-module = <&omap_control_sata>;
130	clocks = <&sys_clkin1>, <&sata_ref_clk>;
131	clock-names = "sysclk", "refclk";
132	syscon-pllreset = <&scm_conf 0x3fc>;
133	#phy-cells = <0>;
134};
135